• 한국HCI학회:학술대회논문집
• /
• 한국HCI학회 2008년도 학술대회 1부
• /
• pp.224-229
• /
• 2008

본 논문에서는 테이블 탑 디스플레이의 사용에서 증강현실을 구현하기 위해 현실 세계에서의 객체를 통한 가상세계의 객체에 영향을 줄 수 있는 객체 컨트롤 입력장치를 제안한다. 이를 위해 본 논문에서는 테이블 탑 인터페이스의 LED 기반 객체 컨트롤 입력장치를 사용하여 네트워크상에서 상호 화면의 제어를 가능하게 하고 입력이 능동적이고 자연스럽도록 하였다. 객체 컨트롤 장치는 적외선 LED를 이용하여 테이블 탑 디스플레이에서 인식이 되도록 하였다. 테이블 탑에서 이와 같은 기능들의 구현을 본 논문에서는 에어하키 게임의 구현을 통해 보인다. 에어하키는 테이블 위에 퍽을 놓고 라켓으로 퍽을 쳐서 상대방의 골문에 넣어 점수를 얻는 게임이다. 본 논문에서 제안한 객체 컨트롤 장치를 이용함으로써 사용자는 증강현실에서 실제 객체의 이용으로 가상세계 객체에 영향을 줄 수 있는 보다 실감나는 인터페이스를 느낄 수 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권5호
• /
• pp.12-23
• /
• 1994

The two-phase flow is observed in power plants, chemical process plants, and refrigeration systems etc., and it is very important to solve the heat transfer mechanism of a boiler, an automic reactor, a condenser and various types of evaporators. Recently, the problem of two phase heat transfer is braught up in many regions with development of energy saving technique. In flow boiling system it is necessary to store data in each condition because the heat transfer characteristics of flow boiling region vary by the change of flow pattern and the magnetude of heat flux to tube length, and be subtly affected by the flow and heating condition. So basic study for knowing flow pattern in heat transfer region and the relation between heat transfer characteristic and flow condition is desired to accumulate data in wide variety of liquid and flow system in the study of heat transfer of two phase flow. In this study R-113 was selected as working fluid whose properties were programmed by least square method, and experiment was conducted in the region of mass flow $1.628{\times}10^6$~$4.884{\times}10^6$/kg/$m^2$hr with inlet subcooling 10~3$0^{\circ}C$, sustaining test section inlet pressure to 1.5kg$_f$/$cm^2$abs.

• 대한기계학회논문집B
• /
• 제20권7호
• /
• pp.2267-2276
• /
• 1996

공정산업분야 및 분무연소분야에서 많이 사용되고 있는 2유체 분무기에서 출구 초음속유동의 가시화와 하류의 가스압력 측정 결과로부터 다음과 같은 결론을 얻었다. 1) 과소팽창 또는 과대팽창 초음속노즐 유동에서 출구 Mach수가 일정한 경우, 유동이 박리하지 않는다면 가스의 정체압력(유량)이 증가함에 따라 노즐출구에서 충돌정체점까지의 길이와 초음속 유동영역의 길이는 증가한다. 2) 스피팅 현상은 액체공급관 출구의 흡인압력은 분사가스압력이 증가함에 따라 단조증가하지만 분사가스압력이 0.5MPa이상이 되면 증감현상이 커지며 돌출형 노즐에서 유동박리시 급격히 증가한 다음 거의 일정하게 유지된다. 4) 액체공급관 하류축상의 압력변화는 출구의 음압에서 충돌정체점까지 상승한 다음 급강하하고 충격파 세포상의 구조에 따라 진동하면서 대기압에 도달한다.

• 한국수산과학회지
• /
• 제28권1호
• /
• pp.35-48
• /
• 1995

To develop the optimal design method for the longline type scallop culturing facilities in the open sea numerical calculations and hydraulic model experiments are carried out for the stability and function optimization. Using the results for the motion and tension of the facilities, stable design concepts and effects of motion control system by vertical anchor and resistance discs art discussed. The results of this study that can be applied to the design are as follows: 1) Total external forces by design wave $(H_{1/3}\;=\;6,7\;m,\;T_{1/3}\;=\;12sec)$ at the coastal waters of Jumunjin for unit facility (one main line) are estimated to 5-20 tons, and required anchor weights are 10-40 tons in the case of 2-point mooring system. Though the present facilities are stable to steady currents, but is unstable to the extreme wave condition of return period of 10 years. 2) The dimensions and depth of array systems must be designed considering the ecological environments as well as the physical characteristics including the mooring and holding forces that are proportional to the length and relative depth of main line to wave length, and the number of buoys and nets. 3) Oscillation of the facility is influenced by water particle motion and the weight of hanging net, and is excited at both edge, especially at the lee side. To reduce the motion of the nets, the vertical anchoring system and the resistence disc method are recommended by the experimental results, 4) The damage of rope near the anchor by abrasion should be prevented using the ring-type connection parts or anchor chains.

• 한국통신학회논문지
• /
• 제30권3C호
• /
• pp.92-101
• /
• 2005

카메라를 통한 객체의 움직임검출은 불필요한 잡음이나 조명의 변화에 따라 정확한 움직임검출 하는 것은 어렵다. 또한 객체의 유입 후 일정시간 동안 움직임이 없을 경우에는 배경으로 인식될 수도 있다. 본 논문에서는 초기의 배경영상을 기준으로 입력영상과의 차를 구하고 시간에 따라 변화하는 배경영상을 N×M 픽셀 마스크만큼 교체하여 갱신한다. 이미지 픽셀 검사는 모든 픽셀을 연산에 참여시키지 알고 일정한 간격의 그물형으로 이미지의 픽셀을 검색하여 보다 효과적으로 움직임을 검출한다. 또한 픽셀검사를 통하여 검출된 객체의 윤곽점을 이용하여 객체의 최소영역을 설정하여 객체의 움직임을 검출하므로, 매 프레임마다 이미지 검사를 하지 않고도 빠르고 정확하게 움직임 검출이 가능하다. 설계하고 구현한 시스템은 실험을 통한 성능평가에서 90% 이상의 높은 정확도를 보였다.

• Journal of Crop Science and Biotechnology
• /
• 제11권1호
• /
• pp.75-82
• /
• 2008

Functional stay-green is a beneficial trait that may increase grain yield through the sustained photosynthetic competence during monocarpic senescence in cereal crops. The temporal changes of photosynthesis and related characteristics throughout the grain filling period of a stay-green japonica rice "SNU-SG1" was compared in growth chamber conditions with three high-yielding cultivars(HYVs) and their $F_1$ hybrids with SNU-SG1. SNU-SG1 exhibited a typical characteristic of functional stay-green in terms of chlorophyll degradation and photosynthetic competence during grain filling. According to the photosynthesis-light response curve measured at 10 and 35 d after heading for the flag leaf, SNU-SG1 exhibited higher initial light conversion efficiency and thus higher gross photosynthetic rate at light saturation compared to HYVs. Light saturation point was not different among genotypes, ranging from 1000 to 1500 ${\mu}mol$ photon $m^{-2}s^{-1}$. Net photosynthetic rate at light saturation($P_{max}$) of the upper four leaves in SNU-SG1 was much higher and sustained longer throughout grain-filling than HYVs and $F_1$ hybrids. The sustained high photosynthetic competence of SNU-SG1 during grain filling was ascribed to the longer maintenance of high mesophyll conductance that resulted from not only high chlorophyll content and its delayed degradation but also the slow degeneration of photosystem II(PS II) as judged by chlorophyll fluorescence($F_v/F_m$) of flag leaves. $F_1$ hybrids showed slow degeneration of photosystem II similar to the male parent SNU-SG1 while chlorophyll degradation pattern close to female parents, thus exhibiting a little higher $P_{max}$ than female parents. These results suggest that SNU-SG1 has a typical functional stay-green trait that can be utilized for increasing rice yield potential through the improved dry matter production during grain filling.

• 한국주조공학회지
• /
• 제35권4호
• /
• pp.80-87
• /
• 2015

The Al die casting process has been widely used in the manufacturing of automotive parts when the process requires near-net shape casting and a high productive rate. However, porosity arises in the casting process, and this hampers the wider use of this method for the creation of high-durability automotive components. The porosity can be controlled by the shot condition, but, it is critical to set the shot condition in the sleeve, and it remains difficult to optimize the shot condition to avoid air entrapment efficiently. In this study, the 4.5 mm, 2.0 mm plate die castings were fabricated under various shot conditions, such as plunger velocities of 0.7 m/s ~ 3.0 m/s and fast shot set points of the cavity of -25%, 0%, 25%, and 50%. The mold filling behavior of Al melts in the cavity was analyzed by a numerical method. Also, according to the shot conditions, the results of numerical analyses were compared to those of die-casting experiments. The porosity levels of the plate castings were analyzed by X-ray CT images and by density and microstructural analyses. The effects of the porosity on the mechanical properties were analyzed by tensile tests and hardness tests. The simulation results are in good general agreements with the die-casting experimental results. When plunger velocity and fast shot set point are 1.0 m/s and cavity 25% position, castings had optimum condition for good mechanical properties and a low level of porosity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.104-107
• /
• 2001

In order to investigate the effect of Ge addition to the Cu matrix on the microstructure and the critical current density, four kinds of internal tin processed Nb$_3$Sn strands with pure Cu and Cu 0.2, 0.4, 0.6 wt % Ge alloys were drawn to 0.8 mm diameter. The microstructure and critical current of internal tin processed Nb$_3$Sn wires that were heat treated at temperatures ranging from 68$0^{\circ}C$ to 74$0^{\circ}C$ for 240h were investigated. The Ge addition to the matrix did not make workability worse. A Ge rich layer in the Cu-Ge matrix suppressed the growth of the Nb$_3$Sn layer and promoted grain coarsening. The greater the Ge content in the matrix, the lower the net Jc result after Nb$_3$sn reaction heat treatment. There was no significant variation in Jc observed with heat treatment temperature ranging from 68$0^{\circ}C$ to 74$0^{\circ}C$. The values of AC loss of Ge added wires were decreased to 40 % compare with no addition wire. Low AC loss was due to segregation of Ge rich layer in the Cu-Ge matrix. If Ge added wire with thin Nb filaments were fabricated, slow diffusion rate of Sn would be overcome and decreased AC loss that is weak Point of internal tin method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전력기술부문
• /
• pp.145-147
• /
• 2005

This paper presents a methodology for satisfying the thermal comfort of Indoor environment and reducing the summer peak demand power by minimizing the power consumption for an Air-conditioner within a space. KEPCO(Korea Electric Power Corporation) use the fixed duty cycle control method regardless of the indoor thermal environment. This method has disadvantages that energy saying depends on the set-point value of the Air-Conditioner and DLC has no net effects on Air-conditioners if the appliance has a lower operating cycle than the fixed duty cycle. A variable duty cycle estimates the PMV(Predict Mean Vote) at the next step with a predicted temperature and humidity coming from the back propagation neural network model. It is possible to reduce the energy consumption by maintaining the Air-conditioner's OFF state when the PMV lies in the thermal comfort range. The proposed methodology uses the historical real data of Sep. 7th, 2001 from a classroom in seoul to verify the effectiveness of the variable duty cycle method comparing with fixed duty cycle. The result shows that the variable duty cycle reduces the peak demand to 2.6times more than fixed duty cycle and increases the load control ratio by 8% more. Based on the variable duty cycle control algorithm, the effectiveness of DLC is much more improved as compared with the fixed duty cycle.

• Nuclear Engineering and Technology
• /
• 제46권3호
• /
• pp.363-372
• /
• 2014

In this study, we proposed a newly designed sulfuric acid transfer system for the sulfur-iodine (SI) thermochemical cycle. The proposed sulfuric acid transfer system was evaluated using a computational fluid dynamics (CFD) analysis for investigating thermodynamic/hydrodynamic characteristics and material properties. This analysis was conducted to obtain reliable continuous operation parameters; in particular, a thermal analysis was performed on the bellows box and bellows at amplitudes and various frequencies (0.1, 0.5, and 1.0 Hz). However, the high temperatures and strongly corrosive operating conditions of the current sulfuric acid system present challenges with respect to the structural materials of the transfer system. To resolve this issue, we designed a novel transfer system using polytetrafluoroethylene (PTFE, $Teflon^{(R)}$) as a bellows material for the transfer of sulfuric acid. We also carried out a CFD analysis of the design. The CFD results indicated that the maximum applicable temperature of PTFE is about 533 K ($260^{\circ}C$), even though its melting point is around 600 K. This result implies that the PTFE is a potential material for the sulfuric acid transfer system. The CFD simulations also confirmed that the sulfuric acid transfer system was designed properly for this particular investigation.