• 전기전자학회논문지
• /
• 제22권4호
• /
• pp.1152-1157
• /
• 2018

논문에서는 밭농사에 적합하도록 설계된 와이어 기반 농약살포장비의 이동을 위한 구조물 설치 위치의 어려움을 해결하고자 한다. 이를 위해 간접적으로 대지구조를 파악할 수 있는 대지저항률 측정방법과 분석기술을 적용한다. 선정된 밭농사 지역에 일정 간격의 전극을 현장에 설치하고 내장형 제어보드에 다수의 스위치를 구동시켜 대지저항률 데이터를 자동 취득한다. 그리고 2차원 영상복원 알고리즘을 사용하여 대지분석을 수행하고 그 결과를 통해 실제 구조물 타설에 적합한 최적지점을 선정하고자 한다.

• 디지털산업정보학회논문지
• /
• 제14권4호
• /
• pp.101-107
• /
• 2018

In the stripping scan square wave voltammetry (SV+SWV) polarography that is often used to analyze the concentration of heavy metals in water, we must measure the point where the faradic current that flows by the pure oxidation-reduction reaction at the electrode is greater than the capacitive current, the frequency cannot be too high. Therefore we wanted to find the frequency range that can be measured. In order to do this, we came up with a method to analyze the signal using FPGA Soc. With this method, the frequency of the square wave was increased from 10Hz to 400Hz by 10Hz, and the measuring time of the square wave was changed from 96.695% to 96.765% by 0.005% while 1600 experiments were conducted. As a result, the frequency of the square wave maintained a stable area of potential-current within 320Hz and it was possible to measure the potential-current signal when calculating the measuring time within the frequency range of 96.7155%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.100.1-100.1
• /
• 2011

Electrochemical impedance spectroscopy(EIS) are using widely as a useful technique mainly in the field of electrochemical for the analysis of electrode reactions or characteristics of the composites. The response analysis of the systems technique provides comprehensive informations about the characteristic and structure of complex and internal reaction. The EIS is the method to measure impedance of the measurement target classified by the frequency, it select the equivalent impedance model to give same response from the result and it calculate the parameter. Therefore, the chemical reaction inside the fuel cell is to modeling to electrical impedance. And as repeating the same experiment in each of the operating point, we can get each different parameter. As a result, we can establish the equivalent impedance model in each operating point. Therefore, if we use these models, we can evaluate the fuel cell without the internal design parameter of the fuel cell as required in existing modeling. The EIS is used typically technique for distinguish status of fuel cell called SOH(State Of Health). When the fuel cell is degradation, Efficiency and health of the fuel cell is reduced because internal impedance is increase. As usage of these principles, we can evaluate state of fuel cell through the impedance analysis of fuel cells. In this study, we are presents EIS distinction system and algorithm for residential fuel cell systems. At the time of the fuel cell installation in the fields, the EIS system and proposed algorithm will be able to apply as technique for efficiency and performance evaluation about fuel cell system.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.187-187
• /
• 2015

The past thirty years have seen increasingly rapid advances in the field of Indium Tin Oxide (ITO) transparent thin film.[1] However, a major problem with this ITO thin film application is high cost compared with other transparent thin film materials.[2] So far, in order to overcome this disadvantage, we show a transparent ITO/Ag/i-ZnO multilayer thin film electrode can be the solution. In comparison with using amount of ITO as a transparent conducting material, intrinsic-Zinc-Oxide (i-ZnO) based on ITO/Ag/i-ZnO multilayer thin film showed cost-effective and it has not only highly transparent but also conductive properties. The aim of this research has therefore been to try and establish how ITO/Ag/i-ZnO multilayer thin film would be more effective than ITO thin film. Herein, we report ITO/Ag/i-ZnO multilayer thin film properties by using optical spectroscopic method and measuring sheet resistance. At a certain total thickness of thin film, sheet resistance of ITO/Ag/i-ZnO multilayer was drastically decreased than ITO layer approximately $40{\Omega}/{\square}$ at same visible light transmittance.(minimal point $5.2{\Omega}/{\square}$). Tendency, which shows lowly sheet resistive in a certain transmittance, has been observed, hence, it should be suitable for transparent electrode device.

• 지구물리와물리탐사
• /
• 제18권3호
• /
• pp.115-124
• /
• 2015

수변 콘크리트 구조물의 누수 탐지를 위해 변형된 배열을 이용하여 전기비저항 탐사를 실시하였다. 전극을 수면에 설치하여 콘크리트 구조물에 대한 새로운 전기비저항 탐사 방식을 제안하였으며, 해석의 단순화를 위해 선형 전류 송신원을 전류전극으로 사용하였다. 마지막으로 전위차를 얻는 방법에 따라 변형된 3가지 전극 배열을 제안하였고, 동일열전위 배열(direct potential array), 평행열 전위 배열(parallel potential array), 횡단 전위 배열(cross potential array)로 명명하였다. 변형된 전기비저항 탐사법을 수치해석, 실내 모형실험, 현장탐사에 적용한 후 그 결과를 비교 분석하여 수변 콘크리트 구조물의 누수 탐지 기술로서의 적합성을 알아보았다. 비교 분석 결과 동일열 전위 배열, 평행열 전위 배열, 횡단전위 배열 모두 누수가 일어날 때, 누수지점에서 뚜렷한 전위차의 변화 양상을 보여 수변 콘크리트 구조물의 누수 탐지에 유용한 방법임을 확인하였다.

• 대한기계학회논문집B
• /
• 제27권6호
• /
• pp.714-725
• /
• 2003

The theory of the current-type electromagnetic flowmeter for a high temporal resolution was developed for two-phase flow measurements. To predict the output of the current-type flowmeter, the three-dimensional virtual potential distribution C and the newly introduced flow pattern coefficient f were derived and computed. The output of flowmeter depends on the liquid conductivity (sensitive to temperature) and flow configurations of the two-phase flow with the sinusoidal excitation over 100 Hz. The flow pattern coefficient was specially devised to separate the dependency on the flow configuration of the two-phase flow from that on the liquid conductivity which can be expressed with the calibration of single-phase flow. Using the finite difference method, the three-dimensional virtual potential distributions were computed for the electrode of finite size. By taking derivative of the virtual potential, the weight functions were evaluated and compared with existing analytic series solution for the point-electrode. There was a reasonable correspondence between the present and existing results. In addition, the flow pattern coefficients were evaluated for annular flows with various film thicknesses, and compared with the experimental results by the impedance spectroscopy. The numerical results agreed well with the experimental data.

• 자원환경지질
• /
• 제29권3호
• /
• pp.345-355
• /
• 1996

2차원 지하구조를 해석함에 있어 1차원 역산에 근거한 수직탐사자료 해석의 타당성과 수평탐사에 있어 여러가지 전극배열법의 효율성이 연구되었다. 수직암맥, 판상기둥, 매몰수직단층, 램프 (ramp), 복합구조와 같은 2차원 모델로부터 유한차분법을 이용하여 3 포인트, 쌍극자, 베너 (Wenner), 슐럼버저 (Schlumberger) 수평탐사의 겉보기비저항 곡선을 구하고 이를 비교 분석하였다. 수직탐사의 경우에는 슐럼버저와 베너 배열법에 대하여 1차원 역산자료를 내심하여 얻은 자료로부터 2차원 단면도를 구하여 비교하였다. 이러한 2차원 단면도는 각 모델에 대하여 비저항의 수칙, 수평적인 경계면을 잘 보여주고 있다. 또한 슐럼버저 수평탐사의 겉보기 비저항 곡선은 수직적인 비저항의 경계면을 잘 보여주고 있다. 전반적으로 수직, 수평 전기탐사의 경우에 있어 슐럼버저 배열법이 다른 전극배열법보다 우수한 결과를 보여주고 있다. 본 연구로부터, 1차원 역산에 근거한 2차원 지하구조의 해석이 가능함을 알 수 있다.

• Journal of Biosystems Engineering
• /
• 제41권2호
• /
• pp.108-115
• /
• 2016

Purpose: Radio frequency (RF) heating is a promising thawing method, but it frequently causes undesirable problems such as non-uniform heating. This can occur because of the food shape, component distribution, and initial temperature differences between food parts. In this study, RF heating was applied to the thawing of cylindrically shaped pork sirloin by changing the shape of electrodes and the surrounding temperature. Methods: Curved electrodes were utilized to increase the thawing uniformity of cylindrically shaped frozen meat. Pork sirloin in the shape of a half-circle column was frozen in a deep freezer at $-70^{\circ}C$ and then thawed by RF heating with flat and curved electrodes. In order to prevent fast defrosting of the food surface by heat transfer from air to the food, the temperature of the thawing chamber was varied by -5, -10, and $-20^{\circ}C$. The temperature values of the frozen pork sirloin during RF thawing were measured using fiber-optic thermo sensors. Results: After multiple applications of curved electrodes resembling the food shape, and a cooled chamber at $-20^{\circ}C$ the half-cylindrically shaped meat was thawed without surface burning, and the temperature values of each point were similarly increased. However, with the parallel electrode, the frozen meat was partially burned by RF heating and the temperature values of center were overheated. The uniform heating rate and heat transfer prevention from air to the food were crucial factors for RF thawing. In this study, these crucial factors were accomplished by using a curved electrode and lowering the chamber temperature. Conclusions: The curved shape of the electrode and the equipotential surface calculated from the modeling of the parallel capacitor showed the effect of uniform heating of cylindrically shaped frozen food. Moreover, the low chamber temperature was effective on the prevention of the surface burning during RF thawing.

• 한국정보통신학회논문지
• /
• 제3권2호
• /
• pp.291-304
• /
• 1999

주 연구에서는 압전체에서의 IDT 변환기, 음향 반사기에 대한 전기 음향 모드의 결합 모드 방정식을 유도, 정리함으로써 SAW 공진기 필터의 결합 모드를 수학적으로 분석할 수 있는 모델링 방법을 소프트웨어 설계 모듈화하고, SAW 공진기 필터를 구성하고 있는 각 구성 요소에 대한 회로적인 결합 방법의 제안을 통하여 SAW 결합 모드 공진기 필터의 설계 및 시뮬레이션 방법을 제안하였다. 또한, 제작된 소프트웨어 설계 모듈을 시뮬레이션 소프트웨어 패키지화함으로써 설계자가 손쉽게 이동통신기기용 결합 모드 공진기 필터를 설계할 수 있도록 그래픽 사용자 인터페이스를 갖는 SAW 결합 모드 공진기 필터의 설계 시뮬레이터를 구현하였으며 이를 통하여 이동통신기기에서 사용할 수 있는 결합 모드 공진기 필터를 모의 설계하고 주파수 특성을 해석함으로써 그 응용 타당성을 제시하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1229-1232
• /
• 2005

We report the method of preventing the grey color of Bi based glass frits caused by reduction of $Bi_2O_3$. To prevent reduction of $Bi_2O_3$, we controlled the melting temperature. Low melting temperature reduces the reduction of $Bi_2O_3$ and that makes clarity transparent glass cullets. After firing, glass frits that melted at lower temperature showed better transparency. To prevent the browning, we used some additives like CuO, $CeO_2$, CoO and $TiO_2$. The colors of glass cullets were varied according to additives. After firing, dielectric layer contained additives showed better transparency than the one without additives. In the point of reaction between dielectric layer and Ag electrode, CuO was the most effective additive in preventing the yellowing.