• 한국해양공학회지
• /
• 제2권2호
• /
• pp.51-60
• /
• 1988

A data transform is performed by using a point-electrode focusing method in order to obtain accurate and objective interpretation of the borehole normal resistivity data. Two new synthetic curves can be generated through the data transform. The one is an approximate apparent resistivity curve, which would be used to predict the true resistivity of the formation. The other one is a bed boundary coefficient curve, which would be used to distinguish bed boundaries. The accuracy of the normal data interpretation can be improved and this method takes much less computational time than a linear inversion technique. Moreover, this method does not require an initial guess model and limitation of number of unknown parameters. Since this algorithm can be run on a personal computer, an immediate interpretation would be possible at the field work site. If an additional set of electrodes(a=125cm)is attached to a normal resistivity tool which is being used (a=25cm, 50cm, 100cm), the apparent resistivity for the point-electrode focusing device can be calculated, and it would maximize the use of short and long normal resistivity data and promote the accuracy of the interpretation.

• 한국물환경학회지
• /
• 제26권6호
• /
• pp.963-968
• /
• 2010

This study has carried out to evaluate the performance of direct and indirect oxidation electrode for the purpose of decolorization of Rhodamine B (RhB) in water. Four kinds of electrodes were used for comparison: Pt and JP202 (indirect oxidation electrode), Pb and boron doping diamond (BDD, direct oxidation electrode). The effect of applied current (0.5 ~ 2.5 A), electrolyte type (NaCl, KCl, HCl, $Na_2SO_4$ and $H_2SO_4$) and electrolyte concentration (0.5 ~ 2.5 g/L), solution pH (3 ~ 11) and initial RhB concentration (25 ~ 125 mg/L) were evaluated. Experimental results showed that RhB removal efficiency were increased with increase of current, NaCl dosage and decrease of the pH. However, the effect of operating parameter on the RhB removal were different with the electrode type. JP202 electrode was the best electrode from the point of view of performance and energy consumption. The order of removed RhB concentration per energy lie in: JP202>Pt>Pb>BDD.

• Journal of Information Display
• /
• 제9권4호
• /
• pp.1-5
• /
• 2008

This paper investigates the effect of the electrode edge of a patterned vertical alignment (PVA) liquid crystal (LC) device on the viewing angle characteristics. In general, a transmissive LCD applies an LC layer with half-wave retardation for a bright state and with zero retardation for a dark state. The retardation of the LC layer would be distorted in each point, however, when a voltage is applied because of the non-uniform voltage distribution in the electrode edge effect. In this paper, the feasibility of the full effect of the electrode edge on the viewing angle property is considered, and the optical viewing angles of the VA LCD with a uniform half-wave LC layer and the PVA LCD with a practical non-uniform LC layer are compared.

• 전기화학회지
• /
• 제9권4호
• /
• pp.158-169
• /
• 2006

The present article is concerned with the overview of the chemically/surface modified cubic spinel $LiMn_2O_4$ as a cathode electrode far lithium ion secondary batteries. Firstly, this article presented a comprehensive survey of the cubic spinel structure and its correlated electrochemical behaviour of $LiMn_2O_4$. Subsequently, the various kinds of the chemically/surface modified $LiMn_2O_4$ and their electrochemical characteristics were discussed in detail. Finally, this article reviewed our recent research works published on the mechanism of lithium transport through the chemically/surface modified $Li_{1-\delta}Mn_2O_4$ electrode from the kinetic view point by the analyses of the experimental potentiostatic current transients and ac-impedance spectra.

• Bulletin of the Korean Chemical Society
• /
• 제11권6호
• /
• pp.487-493
• /
• 1990

A complete potential profile of an electrical double layer is calculated from a distribution function of charged particles based upon a model where the effect of a charged electrode and the finite size of ion are explicitly included. Electrons which are distributed on the electrode surface are assumed not to penetrate the electrode/electrolyte boundary. Formation of the constant density regions and their effects on potential and the electrical double layer capacitances are studied in great detail. The distribution of surface electrons as well as the constant density regions are found to be essential in characterizing the electrical double layer. The introduction of the ion size into the prior electrical double layer model of an ideally polarizable electrode/point charged electrolyte system, shows a great improvement in its characteristics mostly at negative potential region.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.357-358
• /
• 2013

The non-linear characteristics of ON states are important for the application to the high density cross-point memory industry because the sneak current in neighbor cells occurred during reading, erasing, and writing process. Kw of above 20 in ON states, which is the writing current @ Vwrite/the current @ 1/2Vwrite, was required in cross-point ReRAM memory industry. The high current density non-linear IV curve of ZnSe selector was shown and the ALD HfO2 switching device has the linear properties of ON states and the compliance current of 100 uA. To evaluate the performance of the selection device, we connected itto HfO2 switching device in series. The bottom electrode of the selection device was connected to the top electrode of the RRAM. All of the bias was applied with respect to the top electrode of the selection device, whereas the bottom electrode of the RRAM was grounded. In the cross-point application, 1/2Vwrite and -1/2Vwrite were applied to the word-line and bit-line, respectively, which were connected to the selected cell, and a zero bias was applied to the unselected word-lines and bit-lines. The current @ 1/2Vwrite of the unselected cells was blocked by the selection device, thus eliminating the sneak path and obtaining a writing voltage margin. Using this method, the writing voltage margin was analyzed on the basis of the memory size.

• 한국환경과학회지
• /
• 제17권3호
• /
• pp.335-342
• /
• 2008

This study based on electro-coagulation & oxidation reaction is applied to wastewater treatment. Electro-oxidation reaction is used to remove cyanide(CN) which is contained in plating wastewater. Cyanide is transferred by gases such as $NH_3,\;NO_x,\;CO_2$. Analysis result and removal efficiency of Cyanide which is contained in heavy metal wastewater of plating plant, are shown as following paragraph. In electrode arrangement experiment, removal efficiency of carbon electrode(-)/STS316L electrode(+) arrangement method is superior to carbon electrode(-)/carbon electrode(+) arrangement method. Removal efficiencies of cyanide in different HRT such as 30 min, 45 min, 60 min, 75 min and 90 min are 85.5%, 93.1%, 98.0%, 98.7% and 99.4% respectively in carbon electrode(-)/STS316L electrode(+) arrangement method. Finally we can estimate the critical point at HRT of 60 min which the variation of removal efficiency is decreased and HRT to obtain removal efficiency of less than 1 mg/LCN is minimum 90 min.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.180-187
• /
• 2005

This paper is focused on the development of the flexible electrode for disc-type polymer actuators using Segmented Polyurethane(SPU). This paper consists of two parts. The one is about the mechanical property such as elastic modulus. these parameters mainly affect behaviors of polymer actuators and the other is about the electro-chemical property such as the surface resistance of the composite electrode affects the strength of electrostatic force, results in the deformation of polymer actuators. The Young's modulus was measured by UTM. As result, by increasing the modulus of a body of polymer actuators, the maximum displacement of polymer actuators are decreased. The surface resistance of the electrode was measured by 4 point probe system. Compared with the conductive silver grease, the displacement of polymer actuators using carbon black(CB) composite electrodes is comparably small but CB composite electrode should be the practical approach for the improvement of the performance of all-solid actuators, compared with another types of electrode materials.

• 지구물리와물리탐사
• /
• 제19권1호
• /
• pp.45-50
• /
• 2016

일반적으로 전기비저항 탐사에서는 편의상 점 전원을 사용한다. 만약 철제 케이싱과 같이 긴 전극을 사용한다면 전기비저항 탐사의 탐사 깊이가 증가할 것으로 기대된다. 그러나 긴 전극을 사용하여 회득된 전기비저항 탐사 자료는 통상적인 자료 해석 프로그램으로 처리할 수 없다. 이는 긴 전극에 의해 생성된 1차 전위가 점 전원에 의한 1차 전위와는 서로 다르기 때문이다. 이 연구에서는 긴 전극을 여러 개의 연속된 점 전원으로 대치하는 새로운 전기비저항 탐사 자료 처리 방법을 제안하였다. 이 방법에 의한 전위 분포를 해석적/수치적 해와 비교한 결과, 유한 차분법이나 유한 요소법에 의한 긴 전극을 사용하는 전기비저항 탐사 모델링이 가능함을 확인하였다.

• 폴리머
• /
• 제27권4호
• /
• pp.275-284
• /
• 2003

접착성이 없는 고밀도 폴리에틸렌 (HDPE)과 나노입자 카본블랙 복합체를 대상으로 전극과의 계면 접착 향상과 고분자 가교 특성에 따른 양온도 계수 (PTC) 특성을 연구하였다. 은페이스트를 전극으로 사용하였을 때에는, 전극과 HDPE의 접착 계면 저항으로 인하여 카본함량이 45 wt% 이상에서 1 $\Omega$ 이었으나, 덴드라이트 (dendrite)된 구리 전극의 경우 HDPE와 전극간의 넓은 면적 접촉에 의한 계면 저항이 0.2 $\Omega$ 이하였다. HDPE와 은페이스트의 계면 저항의 증가로 인하여 구리 박막을 사용하였을 때보다 전체적으로 저항이 높게 나타났다. HDPE와 나노입자 카본블랙 복합체는 온도가 증가하여 HDPE의 비캣연화온도까지는 저항이 일정하게 유지하다가, HDPE의 연화점에서 증가하기 시작하여 용융점에서 극대 값을 나타내는 전형적인 PTC특성을 보여주었다. 일반적으로 HDPE의 용융점을 넘어서면 음온도 계수 (NTC) 현상이 나타나는데, 가교결합을 시킨 HDPE의 경우는, 용융점 이상에서 NTC 현상이 나타나지 않고 저항이 일정하게 유지되거나 증가하는 경향이 나타났다. 구리 (copper) 전극과 고분자와의 계면 접촉 면적을 증가시키기 위하여 크롬 (chromium)을 덴드라이트시킨 전극을 사용하여 계면 접촉 저항을 감소시켰다.