• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.11
• /
• pp.821-826
• /
• 2013

The purposes of this research are to study on optimal distance between positive and negative electrodes in dust removal chamber. The experiments were performed with electrode-plate gab arranging in order of 3 cm, 2 cm, 1 cm in series while varying influent flow-rate. From the experimental results of dust removal the optimal influent linear velocity was 6 cm/sec and the total mass of attached dust on the surface of electrode-plate was increased as electrode-plate gab is closer. But in case of electrode-plate gab being very close about 1 cm or so, the attached dust on the surface of electrode-plate was shown releasing from electrode-plate due to dust electric-charge changing (reverse ionization). Evantually. optimal distance between positive and negative electrode-plates was about 2 cm and also optimal dust loading rate was about $24mg/min{\cdot}m^2$.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.5 no.4
• /
• pp.40-46
• /
• 1994

Design and microwave absorbing properties of ferrite plate are investigated for the application to the radiowave absorbers used in anechoic chamber. The required frequency-dependence of complex permeability is determined on the basis of wave-impedance-matching relationship. The plate thickness and matchingfrequency are determined from the complex permeability and dielectric constant, and then compared with the directly measured reflection loss. A systematic variation of material constants and their influence on the microwave absorbing properties are demonstrated.

• Transactions of Materials Processing
• /
• v.27 no.6
• /
• pp.363-369
• /
• 2018

This study measured the mechanical properties of an ash wood under various temperature and humidity conditions and a finite element model was developed to predict the behavior of the wood. A humidity-controlled chamber was developed and used for measuring the dimensional changes of woods under various humidity conditions. The thermal expansion coefficient and the elastic stiffness constants were measured by using a thermal chamber and the three-point bending test along the three principal axes of the wood. A constitutive model was proposed to describe the moisture content and temperature dependent behavior of wood. The proposed model was validated for the warping test of a wood plate. The warping of the plate was calculated using the finite element method. The calculated amount of warping was in consistence with the measurements.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2642-2647
• /
• 2007

This study represents numerical study on the thermal and fluid flow characteristics of exhaust gas in a motorcycle muffler. The reference engine was used 124.cc small displacement. Numerical analysis with computational fluid dynamics(CFD) was carried out to investigate the exhaust gas that flow into a motorcycle muffler. The STAR-CD S/W used to three dimensional steady state CFD analysis in a muffler. And than We got the information of static pressure it is used to structural analysis ant the first baffle plate using the commercial CAE code ANSYS workbench. Exhaust gas flow third chamber from frist chamber and running second chamber. A simulation result shows that each chamber of muffler temperature is about 460 K, 445 and 463K and pressure is about 22,000 Pa, 16,000 Pa and 10,000 Pa.

• Journal of the Korean Society of Combustion
• /
• v.10 no.3
• /
• pp.17-24
• /
• 2005

A sub-millimeter scale catalytic combustor with a simple plate-shaped combustion chamber was fabricated. A porous ceramics support coated with platinum catalyst was placed in the chamber. The combustor has a gallium arsenide window on the top that is transparent to infrared ray. The temperature distribution in the combustion chamber was measured using infrared thermal imager while hydrogen-air premixture is steadily supplied to the combustor. The area where the catalytic reaction took place broaden for higher flow rate and lower equivalence ratio made activated area in the combustion chamber broaden. The amount of coated platinum catalyst did not affect the reaction. Stop of reaction, which is similar to flame quenching of conventional combustion, was investigated. Large content of heat generation and broad activated area are essential criteria to prevent stop of reaction that has a bad effect on the combustor performance.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.10a
• /
• pp.298-299
• /
• 2012

• Proceedings of the Korean Society of Developmental Biology Conference
• /
• 2003.10a
• /
• pp.119-119
• /
• 2003

분만후 젖소의 자궁내 미생물상을 조사하고 미생물로부터 분리한 Lipopolysaccharide를 적용하여 소의 번식효율 증진에 기여하고자 분만후 젖소의 도축장 유래 자궁을 채취하여 혐기적 상태에서 균분리 동정을 실시하였다. 균분리 동정을 위하여, 시료를 1cm$\times$1cm로 채취하여 혐기상태에서 거품이 생길 때까지 vortexing한 후 균액 300$\mu l$를 뽑아 혐기배지에 도말하였고 도말한 plate는 $37{\circ}C$ 혐기chamber에서 24시간 배양하였다. 혐기배지에서 자란 균의 colony를 따서 Mac, BHI+B, BHI 배지에 배양한 후 Gram stain을 실시하였다. BHI 배지에서 자란 균의 colony를 따서 BUA+B 배지에 계대배양하였고 BUA+B 배지에서 자란 균중에 가장 마지막으로 자란 균을 따서 An-IF에 넣고 탁도를 63%T로 맞춘 후 An micro plate에 100$\mu l$씩 분주하였다. 분주한 plate를 $37{\circ}C$ 혐기 chamber에서 20~24시간 동안 배양한 후 Biolog를 실시하였다. 시료의 UV측정을 위하여 Sonic Processor로 세포를 분쇄하였고 분쇄한 세포를 $4{\circ}C$에서 10,000rpm으로 10분간 원심분리한 후 상층액을 분리하여 0.45$\mu m$ 필터로 여과한 다음 여과액을 취하여 UV로 standard(E.coli O26 B6 LPS)와 sample(10배 및 20배 희석액)을 측정하였다. (중략)

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.499-502
• /
• 2004

The temperature distribution of a glass plate heated in the infrared heating chamber has been investigated. Temperature of the glass panel is measured using a set of thermocouples and the optical pyrometer. Temperatures measured by thermocouples have good agreement with those by the pyrometer. The temperature uniformity of the panel is improved with wall reflectivity, which is one of the important factors to uniformly heat the panel

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.2
• /
• pp.69-78
• /
• 1991

전자파장해 측정에 사용되는 대표적인 측정시설에는 접지면(ground plane)을 갖춘 야외시험장 (open area test site), 전자파반무향실(semianechoic chamber), TEM(transverse Electromagnetic) cell, 평행판선로(parallel plate line), 헬름홀츠코일(Helmholtz coil), 전자파잔향실(reverberating chamber) 등이 있으며, 이러한 시설은 시험대상기기의 크기, 주파수대역, 적용규격의 규제치, 측정하고자 하는 전자기장의 형태 및 편파면, 그리고 시험신호의 전기적 특성(주파수영역 또는 시간영역) 등을 고려하여 선택되고 구성되 어야 한다. 실제로 시험장소를 건설하는데 막대한 비용이 소요되고, 큰 측정오차를 유발시킬 수 있기 때문에 매우 신중 하게 설계, 구성하여야 한다.

• Nuclear Engineering and Technology
• /
• v.5 no.2
• /
• pp.132-136
• /
• 1973

Uniformly irradiated parallel-plate ionization chamber filled with a gas free of negative ion-forming contaminants was studied. Computer solutions for the electric field and the positive and negative charge densities at various degrees of saturation were obtained and discussed.