• 한국지반공학회논문집
• /
• 제33권12호
• /
• pp.7-20
• /
• 2017

본 연구에서는 전단특성 및 유변학적 정수를 모두 산정할 수 있는 직접전단실험 장비를 이용하여 조립토와 세립토에 대하여 전단강도 및 유변학적 특성에 대한 입도분포의 영향을 조사하고자 하였다. 최대입경 0.075mm의 세립토와 최대입경이 0.425mm이고, 세립분 함량이 17%인 조립토를 건조상태와 액성한계상태로 조성하여, 산사태 분류기준에 따라 재활성 산사태(reactivated landslide) 혹은 붕괴직후 토석류 속도에 해당하는 전단속도에 대하여 전단강도를 산정하였다. 또한, 유변학적 특성 평가를 위해 액성한계상태로 조성된 조립토와 세립토에 대하여 서로 다른 세 가지의 전단변형률속도로 반복적으로 전단하며 잔류전단강도를 측정하였다. 측정된 잔류전단강도와 전단변형률속도와의 관계를 통해 빙햄모델의 소성 점도와 항복응력을 산정하였다. 건조 및 액성한계상태에서 조성된 시료에 대하여 첨두전단강도에서 산정한 점착력의 경우, 세립토에서 조립토보다 더 크게 산정되었으며, 내부마찰각은 조립토에서 더 크게 산정되었다. 유변학 정수의 경우, 소성 점도와 항복응력이 조립토보다 세립토에서 더 큰 것으로 나타났다. 본 연구는 재활성 산사태 혹은 붕괴직후 토석류의 거동예측에 효과적으로 활용될 것으로 기대된다.

• Journal of Microbiology and Biotechnology
• /
• 제1권1호
• /
• pp.70-74
• /
• 1991

The rheological properties of rifamycin B fermentation broth using Nocardia mediterranei were characterized in concomitance with the chemical changes of the fermentation broth. The data were interpreted with various rheological models. As results, it was found that the rheological behaviour at the early growth phases of the culture was the Newtonian fluid, but it was changed to the non-Newtonian fluid (Casson plastic behaviour) at the later phases of the culture. Rheological parameters viz., apparent viscosity ($\mu_a$), yield shear stress ($\tau_o$), and Casson constant ($K_c$) were changed through the fermentation where cell concentrations were changed and mycelia were greatly branched. Those results indicated that cell concentration and cell morphology played important roles to determine the rheological characters.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1298-1302
• /
• 2000

Electrorheological(HER) and magnetorheologica(MR) fluids have a unique ability to increase the dynamic yield stress of the fluid substantially when electric or magnetic field is applied. ER and MR fluid-based dampers are typically analyzed using Bingham-plastic shear flow analysis under Quasi-steady fully developed flow conditions. An alternative perspective, supported by measurements reported in the literature, is to allow for post-yield shear thinning and shear thickening. To model these, the constant post-yield plastic viscosity in Bingham model can be replaced with a power-law model dependent on shear strain rate that is known as the Herschel-Bulkley fluid model. The objective of this paper is to predict the damping forces analytically in a typical ER bypass damper for variable electric field, or yield stress using Herschel-Bulkley analysis.

• 한국안전학회지
• /
• 제13권1호
• /
• pp.85-91
• /
• 1998

Sol-gel derived silica films were prepared by dip-coating onto polymethylmethacylate with Tetraethoxysilane(TEOS) as starting materials. Film properties such as viscosity and thickness were investigated as a function of dip speed, waterprecursor ratio, sol aging time. IR spectra of the gel films prepared from TEOS at various R are given. At small values of R the absorption peaks assignable to C-H vibration in $-OC_2H_5$ groups are observed around 3000 and 1500-1300 $cm^{-1}$. These bands indicate that the -$-OC_2H_5$ groups are retained in the gel at small values of R because of incomplete hydrolysis of TEOS. Film behaviour was interpreted in terms of the dependence of hydrolysis and condensation rates on the interplay between sol pH and waterprecursor ratio. Film thickness was found to increase by approximately a factor of two as waterprecursor ratio increased from two to six. Film thickness also increased with sol prepolymerization time. Surface quality was correlated with processing conditions.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.39-42
• /
• 2005

For mass production, usually injection mold has multi-cavity which is filled through geometrical balanced runner system. Despite geometrical balanced runner system, filling imbalances between cavity to cavity have always been observed. These filling imbalances are one of the most significant factors to affect quality of plastic parts when molding plastic parts in multi-cavity injection mold. Filling imbalances are results from non-symmetrical shear rate distribution within melt as it flows through the runner system. It has been possible to decrease filling imbalance by optimizing processing conditions, but it has not completely eliminated this phenomenon during injection molding processing. This paper presents a solution of these filling imbalances through using 'runner core pin'. The runner core pin which is developed in this study creates a symmetrical shear distribution within runner. As a result of using runner core pin, a remarkable improvement in reducing filling imbalance was confirmed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 금형가공,미세가공,플라스틱가공 공동 심포지엄
• /
• pp.13-16
• /
• 2005

For mass production, usually injection mold has multi-cavity which is filled through geometrical balanced runner system. Despite geometrical balanced runner system, filling imbalances between cavity to cavity have always been observed. These filing imbalances are one of the most significant factors to affect quality of plastic parts when molding plastic parts in multi-cavity injection mold. Filling imbalances are results from non-symmetrical shear rate distribution within melt as it flows through the runner system. It has been possible to decrease filling imbalance by optimizing processing conditions, but it has not completely eliminated this phenomenon during injection molding processing. This paper presents a solution of these filling imbalances through using 'runner core pin'. The runner core pin which is developed in this study creates a symmetrical shear distribution within runner. As a result of using runner core pin, a remarkable improvement in reducing filling imbalance was confirmed.

• 콘크리트학회논문집
• /
• 제13권6호
• /
• pp.637-644
• /
• 2001

본 논문에서는 콘크리트 댐체의 균열 발생 및 진전해석을 포함하는 비선형 지진해석에서 유한요소망 의존성을 제거시키고 안정적인 해를 얻기 위하여 균열모형으로 사용되는 소성손상모형 및 손상역학모형을 duvaut-lions모형에 기초한 점소성모형으로 정규화하는 방법을 기술하였다. 제안된 방법으로 정규화된 소성손상모형과 그렇지 않은 소성손상모형를 이용하여 지진하중을 받는 콘크리트 댐체의 동적 손상해석을 수행하여 여러 형태의 유한요소망이 해석결과에 미치는 영향을 분석하였다. 해석결과로부터 정규화한 소성손상모형은 유한요소망의 크기 및 배열에 영향을 크게 받지 않고 객관적이며 안정적인 해를 계산하는 반면, 정규화되지 않은 균열모형은 요소망에 의존적인 불안정한 결과를 산출함을 관찰할 수 있었다.

• Design & Manufacturing
• /
• 제17권3호
• /
• pp.28-33
• /
• 2023

The conventional FRP (Fiber Reinforced Plastic) manufacturing process used thermoset resins for ease of molding but faced the issue of non-recyclability. To address these shortcomings, a new process utilizing thermal plastic resin was developed. However, due to the high viscosity of thermal plastic resin, problems such as fiber deformation and a reduced fiber volume fraction occurred during the high-temperature, high-pressure process. In this study, to overcome the limitations of the conventional process, fiber-reinforced composite materials were manufactured through in-situ polymerization using PLA (Poly L-Lactide) resin in the VA-RTM (Vacuum Assistance Resin Transfer Molding) process. The fiber volume of the produced specimens was calculated, and resin impregnation and porosity were confirmed through optical microscopy. Additionally, molecular weight analysis using GPC (Gel Permission Chromatography) demonstrated improvements over the conventional process and emphasized the essential requirement of temperature control.

• 한국건설순환자원학회논문집
• /
• 제6권2호
• /
• pp.103-111
• /
• 2011

본 연구에서는 현재 시멘트 콘크리트 혼합재로서 널리 사용되고 있는 고로수쇄 슬래그와 애쉬의 페이스트 유동특성을 파악하였다. 그 방법으로 혼합재 단독을 사용한 페이스트의 유동특성을 파악하여, 아래와 같은 결론을 얻을 수 있었다. 혼합재 단독의 페이스트 유동특성을 시험하기 위하여, 3종류의 분쇄기를 사용하여 3가지 입도로 분쇄된 분말을 제조하였다. 이 분말을 Rosin-Rammler 분포식을 사용하여 얻은 계수 n 값과 De 값을 유동특성과 비교 분석한 결과에서, 일반적으로 같은 입경 크기 일 때 Ash 분말이 Slag 분말보다 소성점도 및 항복응력이 높았으며, 또한 동일 n 값에서 Ash 분말이 Slag 분말 보다 비교적 높은 소성점도와 항복응력을 나타내었으나, 입도분포 폭의 변화에는 Slag 분말이 Ash 분말 보다 민감한 유동특성의 변화 경향을 나타내었다.

• 한국안전학회지
• /
• 제33권2호
• /
• pp.86-93
• /
• 2018

Recently, the use of composite steel plate concrete structural modules filled with concrete between steel plates of complex internal structure, in which a large amount of studs are installed, is increasing in order to reduce the weight and to increase workability of structures such as LNG storage tanks. However, in Korea, there is no systematic criterion for evaluating the construction performance of composite steel plate concrete structural modules. Therefore, in this study, we propose a filling guideline of concrete for composite steel plate structural module. For this purpose, high filling performance concrete with general strength range was formulated and tested for filling ability and permeability for each formulation. Rheology analysis was performed to quantitatively evaluate the flow characteristics of concrete. The reliability of $T_{500}$ and plastic viscosity was evaluated to reflect the results of each test, and a guideline for high filling concrete satisfying the reliability of 0.9 or more was derived by reflecting the results of the study on the relationship between the $T_{500}$ and plastic viscosity. Through final fill-box test, filling performance was verified and guidelines were suggested.