• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.180-186
• /
• 2002

The simulated die-casting process in which the traditional plaster casting process is combined with Rapid Prototyping technology is being used to produce Al, Mg, and Zn die-casting prototypes. Unlike in the die-casting process, molten metal in the conventional plaster casting process is fed via a gravity pour into a mold and the mold does not cool as quickly as a die-casting mold. The plaster castings have much larger and grosser grain structure as compared as the die-castings and the thin walls of the plaster mold cavity may not be completely fillet Because of lower mechanical properties induced by the large grain structure and incomplete Idling, the conventional plaster casting process is not suitable for the trial die-casting Process. In this work, an enhanced trial die-casting process has been developed in which molten metal in the plaster mold cavity is vibrated and pressurized simultaneously. Patterns for the casting are made by Rapid Prototyping technologies and then plaster molds, which have runner system, are made using these patterns. Imparted pressurized vibration to molten metal has made grain structure of castings much finer and improved fluidity of the molten metal enough to obtain complete filling at thin walls which can not be filled in the conventional plaster casting process.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.9
• /
• pp.101-109
• /
• 2001

The simulated die casting process in which the traditional plaster casting process is combined with rapid prototyping technology is being used to produce Al, Mg and Zn die casting prototypes. Because of lower mechanical properties induced by the large grain structure and incomplete filling, conventional plaster casting is not suitable for the simulated die casting process. A plaster casting process with pressurized vibration was developed for the simulated die casting process[5]. In this paper, numerical simulation for the filling stage of the process has been performed to show the effect of the pressurized vibration for complete filling. Treatment of boundary condition based on the finite element method has been proposed for imparted pressurized vibration in the plaster casting process.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.7
• /
• pp.167-173
• /
• 2001

The simulated die-casting process in which the traditional plaster casting process is combined with Rapid Prototyping technology is being used to produce AI, Mg, and Zn die-casting prototypes. Unlike in the die-casting process, molten metal in the conventional plaster casting process is fed via a gravity pour into a mold and the mold does not cool as quickly as a die-casting mold. The plaster castings have much larger and grosser grain structure as compared with the normal die-castings and the thin walls of the plaster mold cavity may not be completely filled. Because of lower mechanical properties induced by the large grain structure and incomplete filling, the conventional plaster casting process is not suitable for the trial die-casting process to obtain quality prototypes. In this work, an enhanced trial die-casting process has been developed in which molten metal in the plaster mold cavity is vibrated and pressurized simultaneously. Patterns for the casting are made by Rapid Prototyping technologies and then plaster molds, which have a runner system, are made using these patterns. Pressurized vibration to imparted molten metal has made grain structure of castings much finer and improved fluidity of the molten enough to obtain complete filling at thin walls which may not be filled in the conventional plaster casting process..

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.1
• /
• pp.56-61
• /
• 2001

This work is concerned with the development of a new plaster die casting process the combines pressurization and vibration for the prototyping of die-castings, and also with a plaster die-casting machine that has a structure quite similar to that of an ordinary die casting machine. The machine utilized an air cylinder for pressurization and a magnetic actuator for vibration. A rapid prototyped pattern is made by the LOM process to prepare a plaster mold. In the process, a plunger int he developed machine simultaneously pressurizes and vibrates the molten metal to fill the plaster mold completely and to facilitate the creation of nuclei in the molten metal, respectively. The developed machine produced a prototype of an end clutch cover with a remarkable improvement in mechanical properties.

• Journal of Korea Foundry Society
• /
• v.4 no.4
• /
• pp.5-13
• /
• 1984

This paper is presented for showing the effect of cooling rate on dendrite arm spacing, correlated with the chilling power of molding materials (conventional plaster, foamed plaster, silica sand) and section thickness, and also showing relationship between dendrite arm spacing and mechanical properties for an aluminum - 8.6 percent silicon - 3.6 percent copper alloy. Local solidification time $(t_f)$ and secondary dendrite arm spacing (d) could be varied widely in accordance with the molding materials and casting thickness, and the following relationship is obtained: $d=9.4t_f\;^{0.31}$ A good correlation between dendrite arm spacing and mechanical properties such as ultimate tensile strength, yield strength, hardness was found, that is, mechanical properties decreased in a linear manner with increase in log of secondary dendrite arm spacing. Ultimate tensile strength in conventional plaster mold casting decreased by 15 percent comparing with the sand casting, where as in foamed plaster mold casting, it decreased by 30 percent comparing with the sand casting. From those results, it has been verified that DAS might be the most representative parameter for predicting mechanical properties varing with the different cooling condition.

• Journal of Technologic Dentistry
• /
• v.35 no.1
• /
• pp.57-64
• /
• 2013

Purpose: Waste parts of zirconia blocks and powders were remained after CAD/CAM process. In order to make these residual zirconia fit for practical use, zirconia single cores were produced by drain casting process. Methods: Remained zirconia blocks were reduced to powders with zirconia mortar, and screened with 180 mesh sieve. Zirconia slip was prepared from waste parts of zirconia by ball milling. Plaster molds for forming cores by slip casting were also prepared. Formed cores were removed from mold after partial drying. Dried cores were biscuit fired at $1,100^{\circ}C$ for 1hour. Biscuit fired cores were treated with tools to control the fitness and thickness. Finished cores were $2^{nd}$ fired at $1,500^{\circ}C$ for 1hour. Microstructure of cross section of core was observed by SEM. Results: When mill pot was filled with 100g of zirconia and alumina mixed powder, 300g of zirconia ball, and 180g of distilled water, the optimum slip for drain casting was obtained. Gypsum plaster for ceramic forming was more suitable then yellow stone plaster for casting process. SEM photograph showed the microstructure of fully dense with uniform grain size of zirconia and well dispersed alumina grains into the zirconia matrix. Conclusion: Zirconia single cores were produced by drain casting process. Drain casting is useful process to make these residual zirconia fit for practical use. Further study will be focused on the preparation of the bridge type cores by casting.

• Journal of the Korean Ceramic Society
• /
• v.28 no.12
• /
• pp.1019-1025
• /
• 1991

The effect of dissolved Ca ion from plaster mold during slip casting on the microstructure and fracture toughness of high-purity sintered alumina were investigated. When the alumina slip containing 1000 ppm MgO was casted on a calcined alumina mold, the sintered compact had a homogeneous microstructure with equiaxed grains. However, when the same slip was casted on a plaster mold, the sintered compact consisted of the mixture of equiaxed and elongated grains. This inhomogeneous microstructure was also observed in the sintered alumina doped with 100o ppm MgO and 100 ppm CaO whose compact was prepared on the calcined alumina mold indicating that the inhomogeneity was caused by CaO. It was found that the specimen containing both MgO and CaO had higher fracture toughness than that containing MgO only. The enhanced fracture toughness by CaO is probably due to the crack deflection along the boundaries of the elongated grains.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.2
• /
• pp.81-88
• /
• 2014

Synthetic products such as casting tape and splints are rapidly replacing conventional plaster casts to treat orthopedic patients. Most synthetic products are produced through a polymerization process with related chemical agents. In this study, the effect of the process parameters on the residual NCO content within a prepolymer for casting tape and the hardening temperature for casting tape were experimentally evaluated. In order to verify the effects of the process parameters, an experimental method was adopted. From an S/N ratio analysis, optimal parameter combinations were determined to produce a pre-polymer with a suitable residual NCO content and alower hardening temperature. Prediction models for the NCO content and the hardening temperature were developed and confirmed.

• Journal of the Korea Convergence Society
• /
• v.12 no.3
• /
• pp.141-149
• /
• 2021

3D printers, which emerged in the late 20th century, have become a key part of the fourth industrial revolution in the 21st century. Although 3D printers, the key equipment of the maker movement and the starting point of the new cottage industry in the 21st century, still reveal the limitations of mass production with low output speed and limited filament materials, the use of 3D printers by ceramic craftsmen has recently increased exponentially. However, as part of a way to overcome the discord between craftsmanship and the new technology, which has been repeated over and over in the past in craft history, the study focused on the 'plaster mold casting' technique using 3D printers. Therefore, after analyzing casting techniques of Tony Hansen, Webe van Gansbeck, Jade Crompton, and Ryu Hee-do, the potters who actively developed gypsum techniques in the world's ceramic crafts field and applied them to their own designs, I tried to find the point of convergence between 3D printers and ceramic crafts by presenting examples of effective 3D modeling methods and optimal slip casting methods using 3D printers.

• Transactions of Materials Processing
• /
• v.10 no.6
• /
• pp.500-508
• /
• 2001

The integration of Rapid prototyping (RP) and Rapid Tooling (RT) has the potential for rapid net shaping of thee-dimensional parts, which have a geometrical complexity. In this study, a new R)P process, (VLM-SP), was proposed to manufacture net shapes of three-dimensional prototypes and it was shown that VLM-SP is an effective and economic process through the comparison of building time, building cost and dimensional accuracy for the test parts with the commercial RP processes ; LOM and FDM. In addition, the metal parts, which are a spanner shape and a clover punch, were produced by the plaster casting as one of RT using the prototypes of VLM-SP.