• Korean Journal of Materials Research
• /
• v.31 no.3
• /
• pp.162-171
• /
• 2021

Dry etching of copper thin films is performed using high density plasma of ethylenediamine (EDA)/hexafluoroisopropanol (HFIP)/Ar gas mixture. The etch rates, etch selectivities and etch profiles of the copper thin films are improved by adding HFIP to EDA/Ar gas. As the EDA/HFIP concentration in EDA/HFIP/Ar increases, the etch rate of copper thin films decreases, whereas the etch profile is improved. In the EDA/HFIP/Ar gas mixture, the optimal ratio of EDA to HFIP is investigated. In addition, the etch parameters including ICP source power, dc-bias voltage, process pressure are varied to examine the etch characteristics. Optical emission spectroscopy results show that among all species, [CH], [CN] and [H] are the main species in the EDA/HFIP/Ar plasma. The X-ray photoelectron spectroscopy results indicate the formation of CuCN compound and C-N-H-containing polymers during the etching process, leading to a good etch profile. Finally, anisotropic etch profiles of the copper thin films patterned with 150 nm scale are obtained in EDA/HFIP/Ar gas mixture.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.182-185
• /
• 2003

Etching characteristics of (PB,Sr)$TiO_3$(PST) thin films Were investigated using inductively coupled chlorine based plasma system as functions of gas mixing ratio, RF power and DC bias voltage. It was found that increasing of Ar content in gas mixture' lead to sufficient increasing of etch rate and selectivity of PST to Pt. The maximum etch rate of PST film is 562 ${\AA}$/min and the selectivity of PST film to Pt is 0.8 at $Cl_2/(Cl_2+Ar)$ of 20 %. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.7-11
• /
• 2002

In this study, Au thin films were etched with a $Cl_2/Ar$ gas combination in an in an inductively coupled plasma. The etch properties were measured for different gas mixing ratios of $Cl_2/(Cl_2+Ar)$ while the other process conditions were fixed at rf power (700 W), dc bias voltage (150 V), and chamber pressure (15 mTorr). The highest etch rate of the Au thin film was 3500 $\AA/min$ and the selectivity of Au to $SiO_2$ was 4.38 at a $Cl_2/(Cl_2+Ar)$ gas mixing ratio of 0.2. The surface reaction of the etched Au thin films was investigated using x-ray photoelectron spectroscopy (XPS) analysis. There is Au-Cl bonding by chemical reaction between Cl and Au. During the etching of Au thin films in $Cl_2/Ar$ plasma, Au-Cl bond is formed, and these products can be removed by the physical bombardment of Ar ions. In addition, Optical emission spectroscopy (OES) were investigated to analyze radical density of Cl and Ar in plasma. The profile of etched Au investigated with scanning electron microscopy (SEM).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.915-918
• /
• 2010

In this work, the etching characteristics of ZnO thin films were investigated using an inductively coupled plasma(ICP) of HBr/Ar/$CHF_3$ gas mixtures. The plasma characteristics were analyzed by a quadrupole mass spectrometer (QMS) and double langmuir probe (DLP). The surface reaction of the ZnO thin films was investigated using X-ray photoelectron spectroscopy (XPS). The etch rate of ZnO was measured as a function of the $CHF_3$ mixing ratio in the range of 0-15% in an HBr:Ar=5:2 plasma at a fixed gas pressure (6mTorr), input power (700 W), bias power (200 W) and total gas flow rate(50sccm). The etch rate of the ZnO films decreased with increasing $CHF_3$ fraction due to the etch-blocking polymer layer formation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.718-722
• /
• 2011

In this work, we investigated to the etching characteristics of the TiN thin film in He/$BCl_3/Cl_2$ plasma. The etch rate was measured by the gas mixing ratio, the RF power, the DC bias voltage and the process pressure. The maximum etch rate in He/$BCl_3/Cl_2$ plasma was 59 nm/min. The etch rate increased as the RF power and the DC-bias voltage was increased. The chemical reaction on the surface of the etched the TiN thin films was investigated with X-ray photoelectron spectroscopy (XPS). The intensity of Ti 2p and N 1s peaks are varied during etching process. A new peak was appeared in He/$BCl_3/Cl_2$ plasma. The new peak was revealed Ti-$Cl_x$ by Cl 2p peak of XPS wild scan spectra analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.58-62
• /
• 2003

Silicon carbide (SiC) was etched in a $NF_3/CH_4$ inductively coupled plasma. The etch process was modeled by using a neural network called generalized regression neural network (GRNN). For modeling, the process was characterized by a $2^4$ full factorial experiment with one center point. To test model appropriateness, additional test data of 16 experiments were conducted. Particularly, the GRNN predictive capability was drastically improved by a genetic algorithm (GA). This was demonstrated by an improvement of more than 80% compared to a conventionally obtained model. Predicted model behaviors were highly consistent with actual measurements. From the optimized model, several plots were generated to examine etch rate variation under various plasma conditions. Unlike the typical behavior, the etch rate variation was quite different depending on the bias power Under lower bias powers, the source power effect was strongly dependent on induced dc bias. The etch rate was strongly correated to the do bias induced by the gas ratio. Particularly, the etch rate variation with the bias power at different gas ratio seemed to be limited by the etchant supply.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.824-827
• /
• 2000

Fabrication of InP-based photonic devices by dry etch Process is important for clear formation of waveguide mesa structure. We have developed more efficient etch process of the inductively coupled plasma (ICP) with low damages and less polymeric deposits for the InP-based photonic devices than the reactive ion etching (RIE) technique. We report the tendency of etch rate variation by the process parameters of the RF power, pressure, gas flow rate, and the gas mixing ratio. The surface roughness of InP-based waveguide structure was more improved by the light wet etching in the mixed solution of H$_2$SO$_4$:H$_2$O (1:1)

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.798-800
• /
• 1998

(Ba,Sr)$TiO_3$ thin films were etched with $Cl_2$/Ar gas mixing ratio in an inductively coupled plasma (ICP) by varying the etching parameter such as f power, do bias voltage, and chamber pressure. The etch rate was $560{\AA}/min$ under Cl_2/(Cl_2+Ar)$ gas mixing ratio of 0.2, rf power of 600 W, do bias voltage of 250 V, and chamber pressure of 5 mTorr, At this time, the selectivity of BST to Pt, $SiO_2$ was respectively 0.52, 0.43. The surface reaction of the etched (Ba,Sr)$TiO_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS).

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1509-1511
• /
• 2001

In this study, etching characteristics of polyimide(Pl) film with $O_2/CF_4$ gas mixing ratio was studied using inductively coupled plasma (ICP). The etch rate and selectivity were evaluated to chamber pressure and gas mixing ratio. High etch rate (over 8000$\AA$/min) and vertical profile were acquired in $CF_4$/($CF_4+O_2$) of 0.2. The selectivities of polyimide to PR and polyimide to $SiO_2$ were 1.15, 5.85, respectively. The profiles of polyimide film etched in $CF_4/O_2$ were measured by a scanning electron microscope (SEM) with using an aluminum hard mask pattern. The chemical states on the polyimide film surface were measured by x-ray photoelectron spectroscopy (XPS).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.4
• /
• pp.319-324
• /
• 2002

In this study, the reduce of plasma etching damage in PZT thin film with addictive gas and re-annealing after etching have been investigated. The PZT thin films were etched as a function of $Cl_2/CF_4$ with addition of Ar and $O_2$ with inductively coupled plasma. The etch rates of PZT thin films were 1450 ${\AA}/min$ at 30% additive Ar and 1100 ${\AA}/min$ at 10% auditive $O_2$ into $Cl_2/CF_4$ gas mixing ratio of 8/2. In order to reduce plasma damage of PZT thin films after etching, the etched PZT thin films were re-annealed at various temperatures at $O_2$ atmosphere. From the hysteresis curries, the ferroelectric properties are improved by $O_2$ re-annealing process. The improvement of ferroelectric behavior at annealed PZT films is consistent wish the increase of the (100) and (200) PZT peaks revealed by x-ray diffraction (XRD). From x ray photoelectron spectroscopy (XPS) analysis, the intensity of Pb-O, Zr-O and Ti-O peak are increased and the chemical residue peak is reduced by $O_2$ re-annealing. The ferroelectric behavior consistent with the dielectric nature of $Ti_xO_y$ is recovered by $O_2$ recombination during rapid thermal annealing process.