• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.3
• /
• pp.102-105
• /
• 2001

A parametric cmpariosn of etch rate and etch selectivity has been performed for GaN, InN and AIN etched in chlorine- and boron halides-based Inductively Coupled Plasma (ICP) discharges. Chlorine-based chemistries produced controllable etch rates (50~150 nm/min) and maximum etch selectivities ~6 for InN over GaN and ~10 for InN over AlN. Maximum etch selectivities of ~100 for InN over GaN and InN over AlN were obtained in boron halides-based discharges and smooth etched surface morphologies were also achieved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.866-869
• /
• 2001

In this study, (Ba,Sr)TiO$_3$(BST) thin films were etched with a magnetically enhanced inductively coupled plasma(MEICP). Etching characteristics of BST thin films including etch rate and selectivity were evaluated as a function of the etching parameters such as gas mixing ratio, rf power, dc bias voltage and chamber pressure. The maximum etch rate of the BST films was 1700 $\AA$/min at Ar(90)/CF$_4$(10), 600 W/350 V and 5 mTorr. The selectivity of BST to PR was 0.6, 0.7, respectively. To analyze the composition of surface residue remaining after the etching, samples etched with different CF$_4$/Ar gas mixing ratio were investigated with X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometry (SIMS). From the results of XPS and SIMS, there are chemical reaction between Ba, Sr, Ti and C, F radicals during the etching and remained on the surface.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1509-1511
• /
• 2001

In this study, etching characteristics of polyimide(Pl) film with $O_2/CF_4$ gas mixing ratio was studied using inductively coupled plasma (ICP). The etch rate and selectivity were evaluated to chamber pressure and gas mixing ratio. High etch rate (over 8000$\AA$/min) and vertical profile were acquired in $CF_4$/($CF_4+O_2$) of 0.2. The selectivities of polyimide to PR and polyimide to $SiO_2$ were 1.15, 5.85, respectively. The profiles of polyimide film etched in $CF_4/O_2$ were measured by a scanning electron microscope (SEM) with using an aluminum hard mask pattern. The chemical states on the polyimide film surface were measured by x-ray photoelectron spectroscopy (XPS).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.726-729
• /
• 2004

Etching characteristics of (Pb,Sr)$TiO_3$(PST) thin films were investigated using inductively coupled chlorine based plasma system as functions of gas mixing ratio, RF power and DC bias voltage. It was found that increasing of hi content in gas mixture lead to sufficient increasing of etch rate and selectivity of PST to Pt. The maximum etch rate of PST film is $562{\AA}/min$ and the selectivity of PST film to Pt is 0.8 at $Cl_2/(Cl_2+Ar)$ of 20 %. It was Proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.3
• /
• pp.27-31
• /
• 2021

VI probe, which is one of various in-situ plasma monitoring sensor, is frequently used for in-situ process monitoring in mass production environment. In this paper, we correlated the plasma etch results with VI probe data with the small amount of gas flow rate changes to propose usefulness of the VI probe in real-time process monitoring. Several different sized contact holes were employed for the etch experiment, and the etched profiles were measured by scanning electron microscope (SEM). Although the shape of etched hole did not show satisfactory relationship with VI probe data, the chamber status changed along the incremental/decremental modification of the amount of gas flow was successfully observed in terms of impedance monitoring.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.327-330
• /
• 2006

We investigated the usefulness of $NbO_{x}$ nanopillars as an etching mask of dry etching for the formation of Si nanodot arrays. The $NbO_{x}$ nanopillar arrays were prepared by the anodic aluminum oxidation process of Al and Nb thin films. The etch rate and etch profile of $NbO_{x}$ nanopillar arrays were examined by varying the experimental conditions such as the concentration of etch gas, coil rf power, and dc bias voltage in the reactive ion etch system using the inductively coupled plasma. As the concentration of $Cl_{2}$ gas increased, the etch rate of $NbO_{x}$nanopillars decreased. With increasing coil rf power and dc bias voltage, the etch rates were found to increase. The etch characteristics and etch mechanism of $NbO_{x}$ nanopillars were investigated by varying the etch time under the selected etch conditions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.1038-1041
• /
• 2003

In the paper, we investigated silicon surface microstructures formed by reactive ion etching in hollow cathode system. Wet anisotropic chemical etching technique use to form random pyramidal structure on <100> silicon wafers usually is not effective in texturing of low-cost multicrystalline silicon wafers because of random orientation nature, but High density hollow cathode plasma system illustrates high deposition rate, better film crystal structure, improved etching characteristics. The etched silicon surface is covered by columnar microstructures with diameters form 50 to 100nm and depth of about 500nm. We used $SF_{6}$ and $O_{2}$ gases in HCP dry etch process. This paper demonstrates very high plasma density of $2{\times}10^{12}$ $cm^{-3}$ at a discharge current of 20 mA. Silicon etch rate of 1.3 ${\mu}s/min$. was achieved with $SF_{6}/O_{2}$ plasma conditions of total gas pressure=50 mTorr, gas flow rate=40 sccm, and rf power=200 W. Our experimental results can be used in various display systems such as thin film growth and etching for TFT-LCDs, emitter tip formations for FEDs, and bright plasma discharge for PDP applications. In this paper we directed our study to the silicon etching properties such as high etching rate, large area uniformity, low power with the high density plasma.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.04a
• /
• pp.71-72
• /
• 2007

In this study, we investigated the fabrication of MLR (multi-layer resist) with a very thin diamond-like carbon (DLC) layer. ArF PR/$SiO_2$/DLC MLR structure was investigated and etching characteristics of the DLC layer was patterned using $SiO_2$ hard-mask by varying the process parameters such as different high-frequency/low-frequency combination ($f_{LF}/f_{HF}$), HF/LF power ratio ($P_{HF}/P_{LF}$), $O_2$ flow and $N_2$ flow rate in $O_2/N_2$/Ar plasmas. The results indicated an increased etch rate of DLC for the higher $f_{LF}/f_{HF}$ combination and for the increased low-frequency power ($P_{LF}$). And the etch rate of DLC was decreased with increasing the $N_2$ flow rate in $O_2/N_2$/Ar plasmas. In order to confirm the application of DLC MLR for the etching process of silicon oxide, the stack of ArF PR/BARC/$SiO_2$/DLC/TEOS/Si was investigated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.12
• /
• pp.1005-1008
• /
• 2009

In this study, adaptively coupled plasma (ACP) source was used for dry etching of $Al_2O_3$ thin film. During the etching process, the wafer surface temperature is an important parameter to influent the etching characteristics. Therefore, the experiments were carried out in ACP to measuring the etch rate, the selectivities of $Al_2O_3$ thin film to mask materials and the etch profile as functions of $Cl_2$/Ar gas ratio and substrate temperature. The highest etch rate of $Al_2O_3$ was 65.4 nm/min at 75% of $Cl_2/(Cl_2+Ar)$ gas mixing ratio. The etched profile was characterized using field effect scanning electron microscopy (FE-SEM). The chemical states of $Al_2O_3$ thin film surfaces were investigated with x-ray photoelectron spectroscopy (XPS).

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.40-44
• /
• 2000

In this paper, since the research on the etching of SrBi$_2$Ta$_2$O$_{9}$ (SBT) thin film was few (specially Cl$_2$-base ), we had studied the surface reaction of SBT thin films using the OES in high density plasma etching as a function of rf power, dc bias voltage, and Cl$_2$/(C1$_2$+Ar) gas mixing ratio. It had been found that the etch rate of SBT thin films appeared to be more affected by the physical sputtering between Ar ions and surface of the SBT compared to the chemical reaction in our previous papers$^{1.2}$ . The change of Cl radical density that is measured by the OES as a function of gas combination showed the change of the etch rate of SBT thin films. Therefore, the chemical reactions between Cl radical in plasma and components of the SBT enhance to increase the etch rates of SBT thin films and these results were confirmed by XPS analysis.