• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.3
• /
• pp.244-250
• /
• 2008

An inductively coupled plasma etching process to replace an existing slower rate reactive ion etching process for $60{\mu}m$ diameter via-holes using Cl2/BCl3 gases has been investigated. Process pressure and platen power were varied at a constant ICP coil power to reproduce the RIE etched $200{\mu}m$ deep via profile, at high etch rate. Desired etch profile was obtained at 40 m Torr pressure, 950 W coil power, 90W platen power with an etch rate ${\sim}4{\mu}m$/min and via etch yield >90% over a 3-inch wafer, using $24{\mu}m$ thick photoresist mask. The etch uniformity and reproducibility obtained for the process were better than 4%. The metallized via-hole dc resistance measured was ${\sim}0.5{\Omega}$ and via inductance value measured was $\sim$83 pH.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.299-304
• /
• 2004

In recent years, silicon carbide has emerged as an important material for MEMS application. In order to fabricate an SiC film based MEMS structure by using chemical etching method, high operating temperature is required due to high chemical stability Therefore, dry etching using plasma is the best solution. SiC film was deposited by thermal CVD at the temperature of 100$0^{\circ}C$ and pressure of 10 torr. SiC was dry etched with a reactive ion etching (RIE) system, using SF$_{6}$/O$_2$ and CF$_4$/O$_2$ gas mixture. Etch rate has been investigated as a function of oxygen concentration in the gas mixture, rf power, working pressure and gas flow rate. Etch rate was measured by surface profiler and FE-SEM. SF$_{6}$/O$_2$ gas mixture showed higher etch rate than CF$_4$/O$_2$ gas mixture. Maximum etch rate appeared at RF Power of 450W. $O_2$ dilute mixtures resulted in an increasing of etch rate up to 40％, and the superior anisotropic cross section was observe

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.770-772
• /
• 1998

The highest etch rate of Pt film was obtained at 10% $Cl_2$/90% Ar gas mixing ratio in our previous investigation. However, the problems such as the etch residues(fence) remained on the pattern sidewall, low selectivity to oxide as mask and low etch slope were presented. In this paper, the etching by additive $O_2$ gas to 10% $Cl_2$/90% Ar gas base was examined. As a result, the fence-free pattern and high etch slope was observed and the selectivity to oxide increased without decreasing of the etch rate. And the reasons for this phenomenon was investigated by XPS(x-ray photoelectron spectroscopy) surface analysis and plasma characteristic.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.2
• /
• pp.62-66
• /
• 2004

This paper investigated the characteristics of a newly developed high density hollow cathode plasma (HCP) system and its application for the etching of silicon wafers. We used SF$_{6}$ and $O_2$ gases in the HCP dry etch process. Silicon etch rate of $0.5\mu\textrm{m}$/min was achieved with $SF_6$$O_2$plasma conditions having a total gas pressure of 50mTorr, and RF power of 100 W. This paper presents surface etching characteristics on a crystalline silicon wafer and large area cast type multicrystlline silicon wafer. The results of this experiment can be used for various display systems such as thin film growth and etching for TFT-LCDs, emitter tip formations for FEDs, and bright plasma discharge for PDP applications.s.

• Journal of the Korean Vacuum Society
• /
• v.15 no.6
• /
• pp.630-636
• /
• 2006

Scale down of semiconductor gate pattern will make progress centrally line width into transistor according to the high integration and high density of flash memory semiconductor. Recently, the many researchers are in the process of developing research for using the ONO(oxide-nitride-oxide) technology for the gate pattern give body to line breadth of less 100 nm. Therefore, etch rate and etch profile of the line width detail of less 100 nm affect important factor in a semiconductor process. In case of increasing of the platen power up to 50 W at the ICP etcher, etch rate and PR selectivity showed good result when the platen power of ICP etcher has 100 W. Also, in case of changing of HBr gas flux at the platen power of 100 W, etch rate was decreasing and PR selectivity is increasing. We founded terms that have etch rate 320 nm/min, PR selectivity 3.5:1 and etch slope have vertical in the case of giving the platen power 100 W and HBr gas 35 sccm at the ICP etcher. Also notch was not formed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.868-871
• /
• 2003

In recent years, silicon carbide has emerged as an important material for MEMS application. In order to fabricate an SiC film based MEMS structure by using chemical etching method, high operating temperature is required due to high chemical stability. Therefore, dry etching using plasma is the best solution. SiC film was deposited by thermal CVD at the temperature of $1000^{\circ}C$ and pressure of 10 torr. SiC was dry etched with a reactive ion etching (RIE) system, using $SF_6/O_2$ and $CF_4/O_2$ gas mixture. Etch rate have been investigated as a function of oxygen concentration in the gas mixture, RF power, and working pressure. Etch rate was measured by surface profiler and FE-SEM. $SF_6/O_2$ gas mixture has been shown high etch rate than $CF_4/O_2$ gas mixture. Maximum etch rate appeared at 450W of RF power. $O_2$ dilute mixtures resulted in an increasing of etch rate up to 40%, and the superior anisotropic cross section was observed.

• Journal of the Korean Ceramic Society
• /
• v.31 no.2
• /
• pp.206-212
• /
• 1994

Effects of the film deposition process parameters on the properties such as deposition rate, etch rate, refractive index, stress and step coverage of plasma enhanced chemical vapor deposited (PECVD) tetraethylorthosilicate glass (TEOS) SiO2 film were investigated and analysed using SEM, FTIR and SIMS techniques. Increasing TEOS flow or decreasing O2 flow increased the deposition rate and the compressive stress of the oxide film but produced a less denser film. The deposition rate decreased owing to the decrease in the sticking coefficient of the TEOS and the O2 molecules onto the substrate Si with increasing the substrate temperature. Increasing the substrate temperature produced a denser film with a lower etch rate and the higher refractive index by lowering SiOH and moisture contents. Increasing the rf power increases the ion bombardment energy. This increase in energy, in turn, increases the deposition rate and tends to make the film denser. No appreciable changes were found in the deposition rate but the refractive index and the stress of the film decreased with increasing the deposition pressure. The carbon content in the plasma TEOS CVD oxide film prepared under our standard deposition conditions were very low according to the SIMS analysis results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.12
• /
• pp.1051-1056
• /
• 2008

In this study, the investigations of the TiN etching characteristics were carried out with addition of $Cl_2$ gas in an inductively coupled $BCl_3$-base plasma system. Dry etching of the TiN was studied by varying the etching parameters including $Cl_2$ gas addition ratio, RF power, DC-bias voltage and pressure. The etch rate of TiN thin film was maximum when the $Cl_2$ gas addition flow was 2 sccm with fixed other conditions. As the RF power DC-bias voltage were increased, the etch rate of TiN thin film showed increasing tendency. $BCl_3/Cl_2$/Ar plasmas were characterized by optical emission spectroscopy (OES) analysis. The chemical reaction on the surface of the etched TiN films was investigated with X-ray photoelectron spectroscopy (XPS).

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.3
• /
• pp.1-4
• /
• 2003

The etching of Au thin films has been performed in an inductively coupled $CF_4 / Cl_2 / Ar$ plasma. The etch properties including etch rate and selectivity were examined as $CF_4$ content adds from o to $30\%$ to $Cl_2/Ar$ plasma. The $Cl_2/(Cl_2 + Ar)$ gas mixing ratio was fixed at $20\%$. Other parameters were fixed at an rf power of 700 W, a dc bias voltage of -150 V, a chamber pressure of 15 mTorr, and a substrate temperature of $30^{\circ}C$. The highest etch rate of the Au thin film was 370 nm/min at a $10\%$ additive $CF_4$ into $Cl_2/Ar$ gas mixture. The surface reaction of the etched Au thin films was investigated using x-ray photoelectron spectroscopy (XPS) analysis. The XPS analysis shows that the intensities of Ail peaks are changed, indicating that there is a chemical reaction between Cl and Au. Au-Cl is hard to remove on the surface because of its high melting point. However, etching products can be sputtered by Ar ion bombardment.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.1
• /
• pp.49-54
• /
• 2014

In this study, we carried out an investigation of the etch characteristics of silicon (Si) film, and the selectivity of Si to $SiO_2$ in $SF_6/O_2$ plasma. The etch rate of the Si film was decreased on adding $O_2$ gas, and the selectivity of Si to $SiO_2$ was increased, on adding $O_2$ gas to the $SF_6$ plasma. The optical condition of the Si film with this work was 1,350 nm/min, at a gas mixing ratio of $SF_6/O_2$ (=130:30 sccm). At the same time, the etch rate was measured as functions of the various etching parameters. The X-ray photoelectron spectroscopy analysis showed the efficient destruction of oxide bonds by ion bombardment, as well as the accumulation of high volatile reaction products on the etched surface. Field emission auger electron spectroscopy analysis was used to examine the efficiency of the ion-stimulated desorption of the reaction products.