• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.498-504
• /
• 2012

Oxide layers were prepared by an environmentally friendly plasma electrolytic oxidation (PEO) process on an Al-1050 substrate. The electrolyte for PEO was an alkali-based solution with $Na_2SiO_3$ (8 g/L) and NaOH (3 g/L). The influence of the electrical parameters on the phase composition, microstructure and properties of the oxide layers formed by PEO were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The voltage-time responses were recorded during various PEO processes. The oxides are composed of two layers and are mainly made of ${\alpha}$-alumina, ${\gamma}$-alumina and mullite phases. The proportion of each phase depends on various electrical parameters. It was found that the surface of the oxides produced at a higher current density and Ia/Ic ratio shows a more homogeneous morphology than those produced with the electrical parameters of a lower current density and lower Ia/Ic ratio. Also, the oxide layers formed at a higher current density and higher Ia/Ic ratio show high micro-hardness levels.

• 한국표면공학회지
• /
• 제56권4호
• /
• pp.250-258
• /
• 2023

Ceramic oxide layer was formed on the surface of high silicon aluminum alloy by using PEO (plasma electrolytic oxidation) process. The microstructure of the oxide layer was analyzed using scanning electron microscopy (SEM) and x-ray diffraction patterns (XRD). The high silicon aluminum alloy prior to PEO process consists of Al, Si and Al₂Cu phases in XRD analysis, whereas Al₂Cu phase selectively disappeared after PEO treatment. Considerable decrease of relative intensity in most of peaks in XRD results of the high silicon aluminum alloy treated by PEO process was observed. It may be attributed to the formation of amorphous phases after PEO treatment. The corrosion behavior of the high silicon aluminum alloy treated by PEO process was investigated using electrochemical impedance spectroscopy (EIS) and other electrochemical techniques (i.e., open circuit potential and polarization curve). Electroanalytical studies indicated that the high silicon aluminum alloy treated by PEO process shows greater corrosion resistance than that untreated by PEO process.

• 한국표면공학회지
• /
• 제50권1호
• /
• pp.17-23
• /
• 2017

This work demonstrates arc generation and anodic film formation behaviors on Al1050 alloy during PEO (plasma electrolytic oxidation) treatment under a constant direct current in an alkaline electrolyte containing silicate, carbonate and borate ions. Only one big arc more than 2 mm diameter was generated first at the edges and it was moving on the fresh surface or staying occasionally at the edges, resulting in the local burning due to generation of an extremely big orange colored arc at the edges. Central region of the flat surface was not fully covered with PEO films even after sufficiently long treatment time because of the local burning problem. The anodic oxides formed on the flat surface by arcing once were found to consist of a number of small oxide nodules with spherical shape of $3{\sim}6{\mu}m$ size and irregular shapes of about $5{\sim}10{\mu}m$ width and $10{\sim}20{\mu}m$ length. The anodic oxide nodules showed uniform thickness of about $3{\mu}m$ and rounded edges. These experimental results suggest that one big arc observed on the specimen surface under the application of a constant direct current is composed of a number of small micro-arcs less than $20{\mu}m$ size.

• 한국재료학회지
• /
• 제17권12호
• /
• pp.648-653
• /
• 2007

Plasma electrolytic oxidation (PEO) treatment was performed on cast Mg-6 wt%Al alloy solution-treated at 693K for 16h and aged at 498K. The surface roughness, thickness, micro-hardness, wear and corrosion properties of coatings on solution-treated and aged Mg-6 wt%Al alloy were investigated. The coatings on aged Mg-6 wt%Al alloy had thinner layer and lower micro-hardness and wear resistance than the solution-treated Mg-6 wt%Al alloy. As the aging time increased, the thickness of coatings decreased while the surface roughness was almost no changed. In addition, the micro-hardness and wear property of coatings decreased with increasing the aging time unlike the uncoated Mg-6 wt%Al alloy showing the peak micro-hardness and the best wear property after aging for 16 h. However, the coatings on Mg-6 wt%Al alloy peak-aged for 16h revealed the best corrosion resistance in 3.5% NaCl solution, which was explained based on the microstructural characteristics.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.270-274
• /
• 2011

Plasma electrolytic oxidation (PEO) treatment was performed on squeeze cast AZ31 alloy and $Al_{18}B_4O_{33}w/AZ31$ composite. Scanning electron microscope (SEM) was employed to characterize the surface morphology and cross-section microstructure of the coating. The phase structures of the PEO coating were analyzed by X-ray diffraction (XRD). The corrosion resistance of the PEO coating was evaluated by electrochemical method. The results showed that the $Al_{18}B_4O_{33}$ whisker on the surface of the composite was decomposed and $MgAl_2O_4$ was formed in the PEO coating layer of $Al_{18}B_4O_{33}w/AZ31$ composite during PEO treatment. As a result, the electrochemical corrosion potential of the PEO coated $Al_{18}B_4O_{33}w/AZ31$ composite was increased compared with that of AZ31 alloy.

• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.601-607
• /
• 2011

The study investigated the influence of current density on the corrosion-protection properties of an AZ91 Mg alloy subjected to plasma electrolytic oxidation coating. The present coatings were carried out under an AC condition at three different current densities, i.e., 100, 150, and $200mA/cm^2$. From microstructural observations, the micro cracks connecting each micro pore were pronounced on the oxide surface of the samples coated at current densities higher than $150mA/cm^2$ since increasing the current density in this study led to an increment in the relative volume fraction of the MgO compound. Based on potentio dynamic polarization and immersion tests, the sample coated at a current density of $100mA/cm^2$ showed superior corrosion resistance.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 추계학술대회 논문집
• /
• pp.322-322
• /
• 2015

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.217-217
• /
• 2012

플라즈마 전해산화(Plasma Electrolytic Oxidation)는 수용액 중에서 Al, Mg, Ti 등의 금속표면에 산화막을 형성시키는 기술로서, 기존의 양극산화법과 유사한 장치에서 고전압을 가해 미세플라즈마 방전을 유도하여 치밀한 산화막을 형성하는 표면처리 기술이다. 본 연구에서는 6061 알루미늄 합금의 대면적 시편을 이용하여 PEO공정으로 산화막을 형성시켰다. 산화막의 조성 및 미세구조는 XRD와 SEM, EDS를 이용하여 분석하였다. 형성된 산화막은 회색에서 밝은 회색으로 시편 전면에 고르게 나타났다. 피막 성장인자를 정교하게 조절함으로써 강한 피막 접착력과 낮은 표면조도를 가지는 매끈한 표면을 얻을 수 있었고, 그에 따른 물성 변화를 분석하였다. 또한 시편의 크기에 관계없이 동일한 조건에서 동일한 물성이 나오는 것으로 분석되었다. 이를 통해 균질한 대면적 피막의 높은 신뢰성을 요구하는 다양한 산업분야에 적합한 표면처리 방법으로서 PEO공정이 활용될 수 있음을 확인하였다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.124-124
• /
• 2014

Plasma Electrolytic Oxidation(PEO)를 적용하여 두께 $120{\mu}m$의 알루미늄 판에 $Al_2O_3$ 산화피막을 형성하였다. 전해액의 주성분 KOH 와 $Na_2SiO_3$에 $Na_3P_2O_7$, $H_3PO_4$의 첨가제를 넣어 산화피막을 분석하였다. 첨가제 $Na_3P_2O_7$ 을 넣었을 때 치밀한 구조를 갖는 산화피막이 형성됨을 알 수 있었다. 특히 KOH, $Na_2SiO_3$, $Na_3P_2O_7$의 비율이 5:5:2 일때 가장 치밀하고 균질한 구조를 갖는 산화피막이 형성되었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.281-282
• /
• 2014

본 연구는 공정시간에 따른 전해 플라즈마 공정(Electrolytic Plasma Processing, EPP) 공정에 의해 형성된 산화 코팅층의 특성 변화를 알아보고자 한다. 실험에 사용되는 전해용액은 $Na_2SiO_3$(12g/l) + $Na_2SiF_6$(0.3g/l)+NaOH(3g/l) 기본용액에 다양한 농도의 NaOH(0-5g/l) 첨가한 전해용액을 사용하였다. AZ61 마그네슘 합금을 모재($22{\Phi}{\times}10mm$)로 사용하였으며 실험은 5분-60분 동안 진행되었다. 공정시간에 변화에 따른 EPP 코팅층 특성을 측정한 결과 공정시간이 증가함에 따라 코팅층 표면의 기공 크기가 커지고 코팅층 내에 기공수가 즐어드는 것을 확인하였다. 또한 XRD 분석을 통하여 형성된 코팅층에서 MgO, Mg2SiO4 상이 나타난 것을 확인할 수 있었다.(No. 2011-0030058),(2012H1B8A2026212)