• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.3
• /
• pp.301-307
• /
• 2015

A bond-based peridynamic model has been shown to be capable of analyzing many of dynamic brittle fracture phenomena. However, there have been issued limitations on handling constitutive models of various materials. Especially, it assumes bonds act independently of each other, so that Poisson's ratio for 3D model is fixed as 1/4 as well as taking only account the bond stretching results in a volume change not a shear change. In this paper a state-based peridynamic model of dynamic brittle fracture is presented. The state-based peridynamic model is a generalized peridynamic model that is able to directly use a constitutive model from the standard theory. It permits the response of a material at a point to depend collectively on the deformation of all bonds connected to the point. Thus, the volume and shear changes of the material can be reproduced by the state-based peridynamic theory. For a linearly elastic solid, a plane stress model is introduced and the damage model suitable for the state-based peridynamic model is discussed. Through a convergence study under decreasing the peridynamic nonlocal region($\delta$-convergence), the dynamic fracture model is verified. It is also shown that the state-based peridynamic model is reliable for modeling dynamic crack propagatoin.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.1
• /
• pp.3-8
• /
• 2008

Polymer-cement composites are known repair materials. The aim of this work is to investigate the influence of various amount of dispersion of carboxylated styrene-butadience copolymer on the selected mechanical properties of polymer-cement concrete (PCC) and on its adhesion to ordinary concrete. The compressive, flexural and tensile strengths as well as frost resistance and fracture resistance of the composites are tested. Adhesion strength of PCC to ordinary concrete, as one of most important performance of good repair material is evaluated and analyzed using three test methods. The results obtained in standard pull-off test are compared with the two other tests. The first one, which is an adaptation of WST (wedge splitting test) characterizes crack propagation in the plane of bond created during repair. In the second test the resistance to shear is a measure of adhesion strength.

• The Journal of Engineering Geology
• /
• v.19 no.2
• /
• pp.145-152
• /
• 2009

Joints are planar tensile opening-mode fractures whose relative motion, as the fracture propagates, is perpendicular to bedding plane and occur in a systematic manner to form a joint set. This paper discusses the mechanical control of joint propagation, the relationship between join spacing and layer thickness, the join saturation, the frequency distribution of join spacing, the joint density, the cross joint, and the development mechanism of joint from a lot of recent joint studies in sedimentary rocks.

• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.53-59
• /
• 1999

Recently, Tailor Welded Blank (TWB) is widely used in automotive industry since the transformation characteristic of its material can be changed. However, clearance between welding surfaces becomes the important factor which affect the quality of the laser weld, causing difficulties in preparing the sheet. The objective of this paper is to systematically evaluate the effects of previously presented fracture criterion and shearing condition on precise mechanical shearing simulation result. For this purpose, a parametric study was peformed to investigate the effect of finite element size and fracture criterion on simulation result. Also, in order to predict the optimum shearing condition, effect of shearing conditions such as clearance and punch radius on the shear plane shape was evaluated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.1
• /
• pp.25-32
• /
• 1989

A finite element program for material nonlinear fracture analysis of reinforced concrete shell was developed. This method can be used to trace the load-displacement response and crack propagation through the elastic and inelastic ranges. A layered isoparametric flat finite element considering the coupling effect between the in-plane and the bending action was developed. Mindlin plate theory taking account of transverse shear deformation was used. The validity of the present program was proved by comparing the numerical results with Hedgren's experimental data.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.755-759
• /
• 1988

Laminated Composites, SS41-Cu-SS41 plates are made by brazing bonding and hot bonding process. Fatigue repeated plane bending tests are carried out and the fracture behavior of Laminated composites, SS41-Cu-SS41 plates are compared with that of homogeneous steel, SS41plates. The following results are obtained; (1) The fatigue life of the brazing bonding plates is higher than those of SS41 plates and hot bonding plates under high stress. (2) The relations between the fatigue crack growth rate, da/dN and stress intensity factor are, da/dN=4.7*10$^{-10}$ $K^{3.20}$, for SS41 da/dN=7.8*10$^{-9}$ $K^{2.43}$, for CAH da/dN=3.6*10$^{-9}$ $K^{2.54}$, for CAB da/dN=1.58*10$^{-9}$ $K^{2.94}$ , for PAH da/dN=1.23*10$^{-9}$ $K^{2.69}$, for PAB

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.676-684
• /
• 2000

In this study, behavior of $C_t$ which is a well-known fracture parameter characterizing creep crack growth rate, is investigated for weld interface cracks. Finite element analyses were per formed for a C(T) specimen under constant loading condition for elastic-plastic-creeping materials. In modeling C(T) geometry, an interface was employed along the crack plane which simulated the interface between weld and base metals. The $C_t$ versus time relations were obtained under various creep constant combinations and plastic constant combinations for weld and base metals, respectively. A unified $C_t$ versus time curve is obtained by normalizing $C_t$ with $C^*$ and t with $t_T$ for all the cases of material constant variations.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.4
• /
• pp.51-56
• /
• 1999

Finite element method was utilized to analyze crack tip stress and displacement field under drying stress case as stepwise loading. Opening mode of single-edge-notched model was employed and analyzed by linear elastic fracture mechanics of plane stress case. The drying stresses were applied as stepwise loads at the boundary elements of the model with 10 steps of time serial. The stress intensity factor($K_I$) for opening mode reached to its maximum just prior to the stress reversal. The $K_I$ from the displacement fields revealed 1.7 times higher than those from stress fields. By comparing the two sets of $K_I$ from displacement and stress fields, single parameter $K_I$ showed its validity to characterize displacement fields around the crack tip front while stress field could not be characterized due to large variations between two sets of data.

• Journal of the Korean Society of Safety
• /
• v.15 no.4
• /
• pp.15-19
• /
• 2000

The exact estimation of the ductile crack growth in a thin sheet would be needed in part of the commercial transport aircraft industry fields. A 2-dimensional elastic plastic finite element analysis was carried out to simulate a stable crack extension in a thin sheet 2024 aluminium alloy. Two kinds of crack modeling were used to evaluate curves of the stable crack extension. And then CTOA(crack tip opening angle) and CTED(crack tip energy density) were calculated in order to determine whether they can be used as useful crack extension criterions in a thin sheet. Results indicate that stable crack extension behaviors were simulated well and CTED is more admirable even though CTOA also is reasonable as a criterion for a stable crack extension in a thin 2024 aluminium alloy sheet.

• Journal of Auto-vehicle Safety Association
• /
• v.6 no.2
• /
• pp.36-42
• /
• 2014

In order to prevent the sharp edge during the side impact, a cause analysis and CAE based risk prediction were carried out in this study. It was found that sharp edge occurs mainly because of stiffness difference between the major parts and structural stress concentration. It could be improved by directly reinforcing the crack initiation region or by weakening the joints connecting the parts. The fracture criterion based on major in-plain strain was suggested and the risk prediction process for sharp edge prevention was established.