• 한국전자파학회지:전자파기술
• /
• 제12권3호
• /
• pp.12-24
• /
• 2001

최근에 이동통신 시스템의 다기능/고기능화에 따 라 여러 선진업체에서 RF부품의 모듈화 개발이 추 진되고 있으며, 이에 대응하여 LTCC를 이용한 MCM (Multi-Chip Module)적층기술의 개발이 확대되고 있 다. 이 기술은 세라믹기판 내부에 L, C, R등의 수 동소자를 3차원적으로 구성, 일체화할 수 있기 때문 에 이들 수동소자 뿐 아니라 세라믹 개별 부품으로 이용되고 있는 대역통과 여파기 및 바이어스라인, 임피던스 매칭 회로, 스트립라인등을 하나의 구조물 에 집적화 시킴으로써 제품의 소형화 및 대량생산 이 가능해진다. 본 논문에서는 LTCC를 활용한 고 집적 복합모듈 기술과 동향에 대한 개요 및 개발사례로서 적층 VCO 모듈의 제작에 대해 소개하기로 한다.

• 한국전자통신학회논문지
• /
• 제9권10호
• /
• pp.1175-1180
• /
• 2014

본 논문에서는 발진기의 위상잡음을 개선하고 MMIC(Monolithic Microwave Integrated Circuit)에 적용 가능하도록 설계된 분리된 링형 DGS(Defected Ground Structure)공진기를 제안한다. 이것은 평면형 공진기로서 소형화 설계가 용이하고 상대적으로 높은 Q 값을 갖는다. 공진기를 이용하여 초고주파 발진기를 설계할 때 공진기의 등가 파라미터를 모델링하는 것이 필요하다. 본 논문에서는 발진기의 설계에 필요한 공진기의 등가회로 파라미터를 공진기의 측정된 특성 값으로부터 수식적으로 계산하는 방법을 나타내었다. 방법을 검증하기 위해 공진주파수가 5.8 GHz인 링형 DGS 공진기를 제작하여 특성을 측정하고 등가 파라미터를 계산하였고, 이 결과를 ADS 도구를 이용하여 시뮬레이션한 결과와 비교하여 일치함을 보였다.

• 대한기계학회논문집B
• /
• 제26권8호
• /
• pp.1145-1152
• /
• 2002

A non-intrusive Planar Laser-Induced Fluorescence(PLIF) technique was applied to study the turbulent mixing process in a Rushton turbine reactor. Instantaneous and ensemble averaged concentration fields was obtained by measuring the fluorescence intensity of Rhodamine B tracer excited by a thin Nd:Yag laser sheet illuminating the whole center plane of the stirred tank. The gray level images captured by a 14-bit cooled CCD camera could be transformed to the local concentration values using a calibration matrix. The dye injection point was selected at the tank wall with three quarter. height (3/4H) from the tank bottom to observe the mixing characteristics in upper bulk flow region. There exist distinct two time scales: the rapid decay of mean concentration after the dye infusion reflects the large scale turbulent mixing while the fellowed slow decay reveals the small scale molecular mixing. The temporal change of concentration variance field conjectures the two sequential processes for the batch type mixing. An inactive column of water is existed above the impeller disk, in which the fluid rotates with the shaft but is isolated from the mean bulk flow.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.57-60
• /
• 2008

KEPRI has studied planar type SOFC stacks using anode-supported single cells and kW class co-generation systems for residential power generation. A 1kW class SOFC system consisted of a hot box part, a cold BOP part and a water reservoir. A hot box part contains a SOFC stack made up of 48 single cells and ferritic stainless steel interconnectors, a fuel reformer, a catalytic combustor and heat exchangers. Thermal management and insulation system were especially designed for self-sustainable operation. A cold BOP part was composed of blowers, pumps, a water trap and system control units. When a 1kW class SOFC system was operated at $750^{\circ}C$ with hydrogen after pre-treatment process, the stack power was 1.2kW at 30 A and 1.6kW at 50A. Turning off an electric furnace, the SOFC system was operated using hydrogen and city gas without any external heat source. Under self-sustainable operation conditions, the stack power was about 1.3kW with hydrogen and 1.2kW with city gas respectively. The system also recuperated heat of about 1.1kW by making hot water.

• 한국정밀공학회지
• /
• 제16권1호통권94호
• /
• pp.95-107
• /
• 1999

The design models of a new product in general are created using clay models or wooden mock-ups. The reverse engineering(RE) technology enables us to quickly create the CAD model of the new product by capturing the surface of the model using laser digitizers or coordinate measuring machines. Rapid prototyping (RP) is another technology that can reduce the product development time by fabricating the physical prototype of a part using a layered manufacturing technique. In reverse engineering process, however, the digitizer generates an enormous amount of point data, and it is time consuming and also inefficient to create surfaces out of these data. In addition, the surfacing operation takes a great deal of time and skill and becomes a bottleneck. In rapid prototyping, a faceted model called STL file has been the industry standard for providing the CAD input to RP machines. It approximates the CAD model of a part using many planar triangular patches and has drawbacks. A novel procedure that overcomes these problems and integrates RE with RP is proposed. Algorithms that drastically reduce the point clouds data have been developed. These methods will facilitate the use of reverse engineered geometric data for rapid prototyping, and thereby will contribute in reducing the product development time.

• 한국전기전자재료학회논문지
• /
• 제31권2호
• /
• pp.117-121
• /
• 2018

Perovskite solar cells have received increasing attention in recent years because of their outstanding power conversion efficiency (exceeding 22%). However, they typically contain toxic Pb, which is a limiting factor for industrialization. We focused on preparing Pb-free perovskite films of Ag-Bi-I trivalent compounds. Perovskite thin films with improved optical properties were obtained by applying an anti-solvent (toluene) washing technique during the spin coating of perovskites. In addition, the surface condition of the perovskite film was optimized using a multi-step thermal annealing treatment. Using the optimized process parameters, $AgBi_2I_7$ perovskite films with good absorption and improved planar surface topography (root mean square roughness decreased from 80 to 26 nm) were obtained. This study is expected to open up new possibilities for the development of high performance $AgBi_2I_7$ perovskite solar cells for applications in Pb-free energy conversion devices.

• 한국분말재료학회지
• /
• 제15권4호
• /
• pp.292-296
• /
• 2008

The electromagnetic (EM) wave absorption properties of the $Fe_{73}Si_{16}B_7Nb_3Cu_1$ nanocrystalline powder mixed with 5 to 20 vol% of Ni-Zn ferrites has been investigated in a frequency range from 100MHz to 10GHz. Amorphous ribbons prepared by a planar flow casting process were pulverized and milled after annealing at 425 for 1 hour. The powder was mixed with a ferrite powder at various volume ratios to tape-cast into a 1.0mm thick sheet. Results showed that the EM wave absorption sheet with Ni-Zn ferrite powder reduced complex permittivity due to low dielectric constant of ferrite compared with nanocrystalline powder, while that with 5 vol% of ferrite showed relatively higher imaginary part of permeability. The sheet mixed with 5 vol% ferrite powder showed the best electromagnetic wave absorption properties at high frequency ranges, which resulted from the increased imaginary part of permeability due to reduced eddy current.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 반도체재료
• /
• pp.22-25
• /
• 2001

A thyristor switch circuit for capacitor discharge application, of which the equivalent circuit includes a resistor between cathode and gate of a reverse-conducting thyristor and an avalanche diode anti-parallel between its anode and gate to set thyristor tum-on voltage, is monolithically integrated by planar process with AVE double-implantation method. To ensure a lower breakdown voltage of the avalanche diode for thyristor tum-on than the break-over voltage of the thyristor, $p^+$ wells on thyristor p base layer are made by boron implantation/drive-in for a steeper doping profile with higher concentrations while rest p layers of thyristor and free-wheeling diode parts are formed with Al implantation/drive-in for a doping profile of lower steepness. The free-wheeling diode part is isolated from the thyristor part by formation of separated p-well emitter for suppressing commutation between them, which is achieved during the formation of thyristor p-base layer.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2175-2178
• /
• 2005

Selective Laser Sintering(SLS) method is one of Rapid Prototyping(RP) technologies. It has been used to fabricate desirable part to sinter powder and stack the fabricated layer. Since the sintering process occurs using infrared laser having high thermal energy, shrinkage and curling of the fabricated part occurs according to thermal distribution. Therefore, the fast scanning path generation is necessary to eliminate the factors of quality deterioration. In case of fabricating larger size parts, the unique scanning device and scanning path generation should be considered. In this paper, the development of SLS machines being capable of large size fabrication(800${\times}$1000${\times}$800 mm, W${\times}$D${\times}$H) will be addressed. The dual laser system and the unique scanning device have been designed and built, which employ CO2 lasers and dynamic 3-axis scanners. The developed system allows scanning a larger planar surface with the desired laser spot size. Also, to generate the fast scanning paths, adaptive path generation is needed with respect to the shape of each layer, and not simply x, y scanning, but the scanning of arbitrary direction should be enabled. To evaluate the suggested method, the complex part will be used for the experiment fabrication.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.150-155
• /
• 2006

Carbon nanotubes backlight unit (CNT-BLU) that lightened by field emission was developed into practicability. According to our novel structure, AC mode circuit design and simple printing process, CNT-BLU could achieve 85% of uniformity, 8000 nits of brightness and low material and fabrication cost. Based on these performances, this new planar backlight technology has chances to proceed to mass production and has the potential to replace traditional backlight technology because of its good properties, like the simple processes, easy to large scale, low surface temperature, low power consumption, optical film-free and Hg-free, etc.