• International Journal of Safety
• /
• v.6 no.1
• /
• pp.22-25
• /
• 2007

Damping out high frequency low amplitude structural vibrations using PZT bimorph is presented. Static and Dynamic analyses of the piezoelectric bimorph bender were performed. Three layer piezoelectric actuators were modeled with SOLID5 coupled-field elements using ANSYS. Static deflection and modal analyses of the piezoelectric bimorph bender are presented. Proper tuning of the values of the resistor and inductor in the shunt circuit is required for maximum vibration suppression.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.4
• /
• pp.658-664
• /
• 2013

In this paper, we present a case study of vibration suppression based on the application of active damping to the small boring process of a boring bar with diameter below ${\Phi}12$. The proposed active damping system consists of an acceleration sensor for real-time monitoring of the vibration signal, a driver for phase control in a computer program, and piezoelectric actuators for damping. In this system, the vibration signals are detected by the acceleration sensor and sent to the computer as an input. The phase shift parameter of the natural frequency of the input signal is sent to the data acquisition board in the computer and calculated by the phase control program. This study confirmed the effectiveness of this damping system, and it opens up the possibility of the development of active damping systems for small boring processes.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.232-236
• /
• 2000

To provide model parameters for servo control system design, dynamic characteristics of a piezoelectric microactuator for hard disk drive(HDD) were investigated. At first frequency response characteristics was measured and a second order model was proposed. Here the amplitude dependent dynamic characteristics such as low frequency gain and damping ratio were studied. In addition, the load current and equivalent impedance of the piezoelectric actuator were measured by varying excitation voltage and frequency. At last, the super-harmonic resonance of the piezoelectric actuator was discussed.

• Journal of Power System Engineering
• /
• v.3 no.4
• /
• pp.36-44
• /
• 1999

회로내에 capacitor를 부가 연결시켜 이론과 실험적으로 고찰한 새로운 기법의 연구이다. 종래에 사용되어 온 전자회로는 낮은 주파수의 진동진폭을 억제할 때에 큰 inductance 값을 필요로 하는 결점이 있었다. 이런 문제점을 해결하기 위하여 본 연구에서는 강화된 압전 분권회로에 병렬로 capacitor를 연결하도록 설계하였다. 새로운 기법은 기계적인 analogy 이론에 의해 증명을 하였으며, 알루미늄 보에 대하여 필요한 동조 모드에서 실험적으로 입증하였다. 따라서 이러한 결과들은 electronic passive damping 에 있어서 예전부터 요구되어 온 절반정도의 inductance값만으로도 구조물의 진동응답을 아주 심도 있게 감소시킬 수 있다는 것을 보여주고 있다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.228-233
• /
• 2002

General modeling of a resonant shunting damper has been made from piezoelectric sensor/actuator equation. It is found that an additional damping, which is augmented to a system, is generated by the shunt damping effect. The transfer function of the tuned electrical absorber is derived for both series and parallel shunt circuit. The governing equations and associated boundary conditions are derived using Hamilton's Principle. The shunt voltage equation is also derived from the charge generated in PZT due to beam vibration. The frequency response function of the obtained mathematical model is compared with that of the tuned electrical absorber and experimental work. The vibration amplitude is reduced about 15 dB at targeted second mode frequency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.994-998
• /
• 2004

Hybrid method is used to suppress vibration of an automotive roof surface. The hybrid method proposed in this paper is implemented experimentally using both viscoelastic and piezoelectric material. The piezoelectric material is used to control the vibration of automotive structure for lower range of frequencies and the experiment of vibration control using viscoelastic material has been carried out suppress vibrations of high frequency range mark. At first the plate controlled by using hybrid method has been .implemented to verify the performance for suppressing vibration. Then the experiment has been applied to the automotive roof structure.

• Smart Structures and Systems
• /
• v.9 no.6
• /
• pp.549-563
• /
• 2012

Theoretical analysis is performed on a multi-mode energy harvester design with focus on the first two vibration modes. Based on the analysis, a modification is proposed for designing a novel adaptive multi-mode energy harvester. The device comprises a simply supported beam with distributed mass and piezoelectric elements, and an adaptive damper that provides a 180 degree phase shift for the motions of two supports only at the second vibration mode. Theoretical analysis and numerical simulations show that the new design can efficiently scavenge energy at the first two vibration modes. The energy harvesting capability of the multi-mode energy harvester is also compared with that of a cantilever-based energy harvester for single-mode vibration. The results show that the energy harvesting capacity is affected by the damping ratios of different designs. For fixed damping ratio and design dimensions, the multi-mode design has higher energy harvesting capacity than the cantilever-based design.

• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.2
• /
• pp.42-49
• /
• 2006

In this paper, an efficient piezoelectric passive damper is newly devised to suppress the multi-mode vibration of plates. To construct the passive damper, the piezoelectric materials are utilized as energy transformer, which can transform the mechanical energy to electrical energy. To dissipate the electrical energy transformed from mechanical energy, multiple resonant shunted piezoelectric circuits are applied. The dynamic governing equations of a coupled electro-mechanical piezoelectric with multiple piezoelectric patches and multiple resonant shunted circuits is derived and solved for the one edge clamped plate. The equations of motion of the piezoelectrics and shunted circuits as well as the plate are discretized by finite element method to estimate more exactly the effectiveness of the piezoelectric passive damper. The method to find the optimal location of a piezoelectric is presented to maximize effectiveness for desired modes. The electro-mechanical coupling term becomes important parameter to select the optimal location.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.262-267
• /
• 2000

The flexural vibration of aluminum beams with active and passive constrained-layer damping has been investigated experimentally to design structure with maximum possible damping capacity. Piezoelectric film is used as sensor and piezoceramic as actuator for negative velocity feedback control. This paper shows the effectiveness of active constrained-layer damping treatment through experiment, and we have carried out an experiment to study effect of beam thickness.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1992.10a
• /
• pp.92-97
• /
• 1992

Undesired vibratory motion of an electric connector is controlled in an active method with piezoelectric sensors and actuators. A special electric control box is developed which is suitable for the purpose. Experimental results show that the system can effectively reduce amplitude responses connector to external forces.