• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.4
• /
• pp.699-704
• /
• 2007

In this paper, optimized model was designed for the starting characteristic of the Single-Phase Line-Start Permanent Magnet Synchronous Motor by using the Design of Experiment. A field pole angle, thickness and distance from center axis of permanent magnet were selected as design factor. We executed the transient state characteristic analysis of 8 test models. The transient state characteristic analysis was executed by using the 2 dimensional Finite Element Method and the Time Difference Method. We checked the fact that the selected design factor affected starting characteristic of the Line-Start Permanent Magnet Synchronous Motor. Depend on this result we found the optimized design point by using the response optimization.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.19-20
• /
• 2003

Brownian-dynamics simulation on highly charged colloidal suspensions is performed by employing Tokuyama effective force recently proposed. The radial distribution function suggests that there exist three novel phases, a gas phase, a liquid droplet phase, and a face-centered cubic (FCC) crystal droplet phase, depending on the minimum values of that potential. The dynamics of droplet growth is also investigated both in liquid droplet phase and in crystal droplet phase. Thus, different types of characteristic growth stages are found.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.318-321
• /
• 1997

This paper is about improving characteristic of plant by using micro-step driver method in 5 phase step motor for satisfying the condition of low oscillation and high accuracy in soldering machine. We choose open loop control method for minimizing hardware system and use one chip microprocessor, power MOSFET nd some device to realize accurate micro-step driver system.

• Journal of electromagnetic engineering and science
• /
• v.3 no.2
• /
• pp.111-117
• /
• 2003

We propose a diode-based RF pre-distorter with various gain and phase characteristics, for non-linearity compensation of RF power amplifiers. This pre-distorter results in the removal of the diode- and configuration-dependent characteristics in the conventional diode-based RF pre-distorters. We have analyzed the operation principle of the proposed pre-distorter. The results show that gain and phase characteristics of the pre-distorter in all four quadrants are achieved. Several power amplifiers and test signals are used for verifying the performance of the proposed diode-based RF pre-distorter.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.340-343
• /
• 2004

The phase transition between amorphous and crystalline states in chalcogenide semiconductor films can controlled by electric pulses or pulsed laser hem: hence some chalcogenide semiconductor films can be applied to electrically write/erase nonvolatile memory devices, where the low conductive amorphous state and the high conductive crystalline state are assigned to binary states. This letters researched into the characteristic of phase change transition in differential Chalcogenide thin films materials. The electrode used Al and experimented on 100nm, 300nm, 500nm respectively.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.663-667
• /
• 1998

This paper describes for reducing harmonic distortion on CO2 welding machine with nonlinear load characteristic using single-switch three-phase AC/DC converter. The low-order harmonic component amplitude of the phase current of single-switch three-phase discontinuous mode is calculated. Experimental results show that CO2 welding machine with single-switch three-phase AC/DC converter is effectively controlled with power factor correction for phase current during welding time.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.3
• /
• pp.224-232
• /
• 2014

PURPOSE. The purpose of the present study was to evaluate the effect of thermocycling and mechanical loading on the biaxial flexural strength and the phase transformation of one Ce-TZP/$Al_2O_3$ and two Y-TZP core materials. MATERIALS AND METHODS. Thirty disc-shaped specimens were obtained from each material. The specimens were randomly divided into three groups (control, thermocycled, and mechanically loaded). Thermocycling was subjected in distilled water for 10000 cycles. Mechanical loading was subjected with 200 N loads at a frequency of 2 Hz for 100000 times. The mean biaxial flexural strength and phase transformation of the specimens were tested. The Weibull modulus, characteristic strength, 10%, 5% and 1% probabilities of failure were calculated using the biaxial flexural strength data. RESULTS. The characteristic strengths of Ce-TZP/$Al_2O_3$ specimens were significantly higher in all groups compared with the other tested materials (P<.001). Statistical results of X-ray diffraction showed that thermocycling and mechanical loading did not affect the monoclinic phase content of the materials. According to Raman spectroscopy results, at the same point and the same material, mechanical loading significantly affected the phase fraction of all materials (P<.05). CONCLUSION. It was concluded that thermocycling and mechanical loading did not show negative effect on the mean biaxial strength of the tested materials.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.2C
• /
• pp.191-200
• /
• 2002

A frequency synthesizer that can be used in IMT-2000 was designed and fabricated using dual loop PLL(Phase Locked Loop) in this paper. For improving phase noise characteristic two loops, reference loop and main loop, were divided. Phase noise was improved by transformed clamp type voltage controled oscillator and optimizing loop bandwidth in reference loop. And voltage controlled oscillator open loop gain in main loop. Fabricated the frequency synthesizer had 1.81GHz center frequency, 160MHz tuning range, 13.5dBm output power and -119.73dBc/Hz low phase noise characteristic.

• The Korean Journal of Nuclear Medicine
• /
• v.1 no.2
• /
• pp.75-84
• /
• 1967

$^{131}I$-labeled-O-iodohippurate renograms in 15 cases of epidemic hemorrhagic fever(E.H. fever)during oliguric, diuretic and convalescent phase were analysed quantitatively and qualitatively, namely by its configuration, Tmax T 1/2 and renal index of Hirakawa. The results were as following: 1) Changes on the renograms in E.H. fever showed simultaneous bilateral renal impairment. 2) The characteristic configurations of renogram in the oliguric phase were: (1) Moderately decreased absolute amplitude of initial spike. (2) Continous rising second slope. (3) No appearance of terminal descent. Those were mast likely to those of renograms in acute ureteral obstruction or acute dehydration state. 3) During the diuretic phase, the renogram showed the point of maximal amplitude, but the steepness of 2nd slope was markedly decreased. The appearance of terminal descents was observed with unusually high amplitude despite of the tremendously large amount of urinary output during this phase. 4) In convalescence, the renograms were essentially normal in configuration, but the renal index of Hirakawa was not recovered until this phase. 5) Renograms in E.H. fever showed the characteristic patterns in each phase of its clinical course. 6) $^{131}I$-OIH-Renogram might be an useful method for the evaluation of renal function in E.H. fever during its course.

• Journal of Ocean Engineering and Technology
• /
• v.2 no.2
• /
• pp.78-86
• /
• 1988

In order to investigate the corrosion pit occurrence and growth characteristic of M.E.F.(martensite encapsulated islands of ferrite) dual phase steel was made with a suitable heat treatment of raw material(SS41), a corrosion fatigue test was performed under rotary bending in the salt solution having a concentration from 0.01 wt percent to 3.5 wt percent. The fatigue strength of dual phase steel was remarkably decreased with an increase in concentration of salt solution; approximately from 63% to 80% in case of dual phase steel and from 40% to 71% in case of raw material. Corrosion pit occurred in the martensite phase and fatigue cracks from corrosion pits were selectively propagated in martensite phases. In the observation of corrosion pits at the origin of fatigue cracks, it had been found that corrosion pits were grown into hemispherical pits and a/c(the surface diameter, 2c and the depth, a of corrosion pit)was about 1.0-1.5regardless of the variation of salt solution concentration. The difference of corrosion pit depth growth rate was increased with an increase in concentration of salt solution according to an increase in stress level.