• 상하수도학회지
• /
• 제22권1호
• /
• pp.87-92
• /
• 2008

Purposes of this study were to evaluate operational performance of submerged membrane bioreactor (MBR) combined with periodic chemical backwash. Five lab-scale submerged MBRs were performed in accordance with NaOH dose, backwash solution volume. While filtration resistance of MBR system without backwash (Control) was increased persistently from startup, those of four MBR systems (RUN 1-4) with chemical backwash were maintained at $(1.4{\pm}0.16){\times}10^{12}$, $(8.6{\pm}0.90){\times}10^{11}$, $(1.9{\pm}0.10){\times}10^{12}$, $(1.4{\pm}0.10){\times}10^{12}l/m$, respectively. Under chemical backwash condition of 0.0230 M, 375 mL, permeability of membrane was highest at flux of $30L/m^2/hr$. According to results from experiment that changing condition of dose and volume, it was estimated that effect of chemical dose acts more greatly than backwash solution volume. Because COD removal rates of all MBR systems with chemical backwash were more than 96%, it was proved that NaOH added to backwash solution did not affect microorganism.

• Korea-Australia Rheology Journal
• /
• 제11권3호
• /
• pp.233-240
• /
• 1999

In order to understand the flow behavior of Electrorheological (ER) fluid, dynamic simulation has been intensively performed for the last decade. When the shear flow is applied, it is easy to carry out the simulation with relatively small number of particles because of the periodic boundary condition. For the squeezing flow, however, it is not easy to apply the periodic boundary condition, and the number of particles needs to be increased to simulate the ER system more realistically. For this reason, the simulation of ER fluid under squeezing flow has been mostly performed with some representative chains or with the approximation that severely restricts the flow geometry to reduce the computational load. In this study, Message Passing Interface (MPI), which is one of the most widely-used parallel processing techniques, has been employed in a dynamic simulation of ER fluid under squeezing flow. As the number of particles used in the simulation could be increased significantly, full domain between the electrodes has been covered. The numerical treatment or the approximation used to reduce the computational load has been evaluated for its validity, and was found to be quite effective. As the number of particles is increased, the fluctuation of the normal stress becomes diminished and the prediction in general was found to be qualitatively In good agreement with the experimental results.

• 산업경영시스템학회지
• /
• 제43권1호
• /
• pp.70-78
• /
• 2020

Under the situation which customer orders are cancelled unless all products in the order are delivered all at once, this paper concentrates on the purchase dependent demands and explores the systematic approach to implant the purchase dependence into the multi-product inventory model. First, by acknowledging that it is a challenging task to formulate a suitable inventory model for the purchase dependence, we derive the optimal solution condition using an EOQ model and extend the optimal solution condition to periodic review models. Then, through the comparison simulation of four inventory policies regarding several degrees of purchase dependence, we demonstrate that the inventory models which consider the purchase dependence generate less total cost than the inventory models which ignore the purchase dependence. In general, the inventory models which consider the purchase dependence reduce the loss of sales by maintaining more inventories, which results in reducing the total cost. Consequently, the simulation result supports the effectiveness of this paper's approach. In addition, this paper uses the individual order period and joint order period obtained from the EOQ model for the multi-product inventory model. Through the in-depth analysis of comparing the two models, we observe that the model of using the joint order period produces less total cost when the degree of purchase dependence is high, but the model of using the individual order period produces less total cost when the degree of purchase dependence is low.

• 한국항공우주학회지
• /
• 제37권6호
• /
• pp.527-536
• /
• 2009

캐스케이드 실험장치에 한 개의 익형을 설치하여 캐스케이드 실험이 가능한 장치벽면의 설계를 수행하였다. 장치의 폭은 피치의 160% 넓이이다. 이 경우에 실험장치 내에 다수개의 블레이드를 설치하는 경우에 비하여 소형의 장치라도 실험의 정확성이 향상되는 장점이 있지만, 피치방향으로 주기조건을 맞추기가 어렵다. 본 연구에서는 주기조건이 얻어지도록 벽면의 형상설계를 내부유동장의 결과를 바탕으로 기울기기반과 유전자알고리즘의 방식을 사용하여 벽면을 설계하였다. 이를 위하여 목적함수는 캐스케이드 익형의 표면에서 얻어진 마하수를 적용하였으며, 실험장치의 형상 조정이 가능한 14개의 설계변수를 적용하였다. 유전자알고리즘에 의한 최적화 설계방식이 향상된 결과를 보여주었다.

• Korean Membrane Journal
• /
• 제9권1호
• /
• pp.12-17
• /
• 2007

We performed periodic water-back-flushing using permeate water to minimize membrane fouling to enhance permeate flux in tubular ceramic microfiltration system for water treatment of high turbid source. The filtration time (FT) = 2 min with periodic 6 sec water-back-flushing showed the highest value of dimensionless permeate flux ($J/J_o$), and the lowest value of resistance of membrane fouling ($R_f$), and we acquired the highest total permeate volume $(V_T)\;=\;6.805L$. Also in the result of BT effect at fixed FT = 10 min and BT (back-flushing time) = 20 sec showed the lowest value of $R_f$ and the highest value of $J/J_o$, and we could obtain the highest $V_T\;=\;6.660\;L$. Consequently, FT = 2 min and BT = 6 sec could be the optimal condition in water treatment of high turbid source above 10 NTU. However, FT = 10 min and BT = 20 sec was superior to reduce operating costs because of lower back-flushing frequency. Then the average quality of water treated by our tubular ceramic MF system was turbidity of 0.07 NTU, $COD_{Mn}$ of 1.86 mg/L and $NH_3-N$ of 0.007 mg/L.

• 제어로봇시스템학회논문지
• /
• 제9권2호
• /
• pp.117-123
• /
• 2003

Rotational machines such as optical disk drives, hard disk drives, and so on are subject to periodic disturbances caused by their mechanical characteristics. In the meanwhile, it is well known that repetitive control rejects periodic disturbance effectively. This paper presents a practical application of repetitive control to the track-following servo of an optical disk drive. The repetitive control system is composed of two repetitive controllers which compensate for periodic disturbances generated by track geometry and eccentric rotation of disk and a feedback controller stabilizing the feedback loop. A robust stability for all plant uncertainties is proved using linear matrix inequalities (LMIs). In the controller design, a weighting function is introduced for the feedback controller to ensure a minimum loop gain and a sufficient phase margin. The repetitive controllers and the feedback controller are designed by solving an optimization problem which can consider the robust stability condition and the system performance. The developed repetitive control system is implemented in the digital control system with a 16-bit fixed-point digital signal processor (DSP). Through simulation and experiment. The feasibility of the proposed repetitive control system is verified.

• 한국소음진동공학회논문집
• /
• 제17권1호
• /
• pp.41-47
• /
• 2007

Scattering fields of two dimensional acoustic waves by a circular cylinder are investigated. The present numerical approach for the acoustic scattering problem has difficulties of numerical robustness, long-time stability and suitability of far-field boundary treatments. The time-dependent periodic acoustic source is used to analyze Interference patterns between incident waves and waves reflected by the cylinder. Characteristic boundary algorithms coupled with 4th order Modified-Flux-Approach ENO(essentially non-oscillatory) schemes are employed in generalized coordinates to examine the effect of the wane frequency on the interference patterns. Non-reflecting boundary conditions, which is crustal for accurate computations of aeroacoustic problems, are used not to contaminate scattering fields by reflected waves at the outer boundary. Computed scattering fields show the circumferential acoustic modes generated by interacting between acoustic sources and scattered waves. At a lower frequency, the wave passes almost straight through the cylinder without Interacting with circular cylinder. Simulation results are presented and compared with the analytic solution. Computed RMS-pressure distribution on the cylinder wall is good agreement with exact solution.

• Korean Membrane Journal
• /
• 제10권1호
• /
• pp.33-38
• /
• 2008

In this study periodic water-back-flushing using permeate water was performed to minimize membrane fouling and to enhance permeate flux in tubular ceramic micro filtration system for Gongji stream water treatment in Chuncheon city. The filtration time (FT) 2 min with periodic 6 sec water-back-flushing showed the highest value of dimensionless permeate flux ($J/J_0$), and the lowest value of resistance of membrane fouling ($R_f$), and we acquired the highest total permeate volume ($V_T$) of 7.44L. Also in the results of BT effect at fixed FT 10 min, BT (back-flushing time) 20 sec showed the lowest value of $R_f$ and the highest value of $J/J_0$, and we could be obtained the highest $V_T$ of 8.04 L. Consequently FT 10 min and BT 20 sec could be the optimal condition in Gongji stream water treatment. Then the average rejection rates of pollutants by our tubular ceramic MF system were 93.8% for Turbidity, 20.7% for $COD_{Mn}$, 39.2% for $NH_3$-N and 31.5% for T-P.

• 대한기관식도과학회:학술대회논문집
• /
• 대한기관식도과학회 1993년도 제27차 학술대회 초록집
• /
• pp.71-71
• /
• 1993

이중음성이란 성대진동이 정상이 아닌 유사주기성에 의해 양측 성대진동의 위상차이때문에 발생되는 소리로서 대표적으로 양측성대의 긴장불균형(tension imbalance)시와 양측성대 사이의 높이차이(level difference)시에 발성직전의 성문열림의 정도에 따라 성대진동의 주기가 서로 다르기 때문에 이중음성이 발생한다고 한다. 그러나 실제 이러한 현상은 일측성대 마비환자뿐 아니라 성대의 점막부위에 증가된 질량효과에 의해 이중음성이 나타날 수 있는데 대표적으로 성대내 낭종이라 하겠다. 본 연구에서는 청각적으로 이중음성을 나타낸 일측성대마비, 성대내낭종 및 성대육아종 등 수술을 받았던 19례를 대상으로 음향학적 분석중 음성파형을 이용한 분석을 한 결과 유사주기성 음성파형에 대한 특징들중에서 파형수, peak변이도, 잡음의 정도등이 각질환에 따라 다른 양상을 보여 이중음성의 발생기전이 질환에 따라 다름을 알 수 있었다.

• Journal of Communications and Networks
• /
• 제15권1호
• /
• pp.87-101
• /
• 2013

In industrial applications, sensor networks have to satisfy specified time requirements of exchanged messages. IEEE 802.15.4 defines the communication protocol of the physical and medium access control layers for wireless sensor networks, which support real-time transmission through guaranteed time slots (GTSs). In order to improve the performance of IEEE 802.15.4 in industrial applications, this paper proposes a new traffic scheduling algorithm for GTS. This algorithm concentrates on time-critical industrial periodic messages and determines the values of network and node parameters for GTS. It guarantees real-time requirements of periodic messages for industrial automation systems up to the order of tens to hundreds of milliseconds depending on the traffic condition of the network system. A series of simulation results are obtained to examine the validity of the scheduling algorithm proposed in this study. The simulation results show that this scheduling algorithm not only guarantees real-time requirements for periodic message but also improves the scalability, bandwidth utilization, and energy efficiency of the network with a slight modification of the existing IEEE 802.15.4 protocol.