In MIPv6, unauthenticated binding updates expose the involved MN and CN to various security attacks. Thus, protecting the binding update process becomes of paramount importance in the MIPv6, and several secure binding update protocols have been proposed. In this paper, we pro-pose a novel protocol for the secure binding updates in MIPv6, which can resolve the drawbacks of the Deng-Zhou-Bao's protocol [2], by adopt-ing Aura's CGA scheme with two hashes [9]. Aura's scheme enables our protocol to achieve stronger security than other CGA-based protocols without a trusted CA, resulting in less cost of verifying the HA's public key than the Deng-Zhou-Bao's protocol. Through the comparison of our protocol with other protocols such as the Deng-Zhou-Bao's protocol, CAM-DH and SUCV, we show that our protocol can provide better performance and manageability in addition to stronger security than other approaches.
An authentication procedure on wired and wireless network will be done based on the registration and management process storing both the user's IP address and client device's MAC address information. However, existent MAC address registration/administration mechanisms were weak in MAC Spoofing attack as the attacker can change his/her own MAC address to client's MAC address. Therefore, an advanced mechanism should be proposed to protect the MAC address spoofing attack. But, existing techniques sequentially compare a sequence number on packet with previous one to distinguish the alteration and modification of MAC address. However, they are not sufficient to actively detect and protect the wireless MAC spoofing attack. In this paper, both AirSensor and AP are used in wireless network for collecting the MAC address on wireless packets. And then proposed module is used for detecting and protecting MAC spoofing attack in real time based on MAC Address Lookup table. The proposed mechanism provides enhanced detection/protection performance and it also provides a real time correspondence mechanism on wireless MAC spoofing attack with minimum delay.
With increased use of neurotoxic agents in manufacturing industries, hazardous effects of neurotoxic agents pose significant problems in protecting health of workers who work in these industries. A normal range of neurobehavioral performance is required to study hazardous effects of neurotoxic agents among workers. However, such reference for Korean population is not available yet. The objective of this study is to estimate a normal range of neurobehavioral test performance of female workers in Korea. Data for neurobehavioral test performance developed by the World Health Organization were obtained from 165 female workers. Study subjects, 140 production workers and 25 clerks, who voluntarily participated in this study were not occupationally exposed to neurotoxic agents. The mean age and the mean education years of them were 32 years and 10.9 years, respectively Santa Ana dexterity, pursuit aiming, digit symbol, simple reaction time, and Benton visual retention tests among the Neurobehavioral Core Test Battery(NCTB) were included in the evaluation. Subjects were interviewed by a trained interviewer for their detailed occupational history $Mean({\pm}SD)$ performance of the participants were: $45.7{\pm}7.1\;and\;41.9{\pm}6.4$ in the Santa Ana dexterity test of the preferred and non-preferred hands; $45.7{\pm}7.1\;and\;41.9{\pm}6.4$ in correct dot of the pursuit aiming test; $57.7{\pm}16.0$ in the digit symbol test; $274.8{\pm}44.6$ msec in the mean simple reaction time and $70.5{\pm}69.0$ msec in the mean standard deviation of it; and $7.8{\pm}1.7$ in the Benton visual retention test. Most neurobehavioral performance scores were correlated significantly with age and educational level. Educational level was found to be a significant independent variable which was associated with all test scores. Age was significantly associated with scores of pursuit aiming and digit symbol tests.
Park, Young-Jun;Lim, Dong-Hyuk;Kim, Hyun-Joong;Song, Hyun-Suk;Kwon, Hyuk-Jin
Journal of Adhesion and Interface
/
v.8
no.2
/
pp.15-21
/
2007
To prepare a natural rubber-based pressure-sensitive adhesive (PSA) for protection film of opto- functionalized sheet, natural rubber (NR) was blended with a DCPD type tackifier and three types of aliphatic hydrocarbon resins, respectively. Also, to supply low cohesion strength of NR, in the fixed ratio of tackifier, synthetic rubber, styrene-isoprene-styrene (SIS) block copolymer was blended with NR as a function of SIS contents. PSA performance of prepared PSAs was evaluated using probe tack and peel strength. Probe tack of NR/tackifier blends was increased with increasing tackifier contents, and showed maximum peak. In addition, probe tack of NR/tackifier blends slightly increased with increasing softening point of aliphatic hydrocarbon resins. Their peel strength increased up to 50 wt% of tackifier contents, but in the over contents of tackifier, they showed stick-slip failure mode. Finally, probe tack of NR/SIS/tackifier blends showed the maximum values at 20~40 wt% of tackifier contents, but at 20 wt% of tackifier contents, they showed fibrillation. For this reason, peel strength showed maximum values at 40 wt% of tackifier contents.
The introduction of dongbal[bara] is in line with Buddhism which was transmitted from India through China. Therefore, this paper tracked down the records of dongbal in Indian and Chinese Buddhism, and especially in scriptures and in ritual texts of Korean Buddhism, and studied the functionality and the use of dongbal, and the attributes of Baramu. Among the scriptures that record dongbal, 『Myobeopyeon hwagyeong(妙法蓮華經)』(A.D.406) is the earliest to be translated. The records of bara in the scriptures were written as dongbal(銅鈸) mostly, and that it was used as ritual tool(法具), instrumental offering, and religious ornament(莊嚴物). The oldest record which can verify that dongbal was used in Korea is 『Seodaesajajaeryugijang(西大寺資財流記帳)』(A.D.780). The oldest cymbals-like relic remaining today, the reliquary from the temple Gameunsa built in A.D.628, dates back to the early period of Unified Silla. This indicates that dongbal has been used at Korean temples by the 7th century at least. The records of dongbal(銅鈸) written in cheong-gyu(淸規, buddhist monastic rules) and ritual texts are classified as myeongbal(鳴鈸) and dongbal(動鈸). The letter 'myeong(鳴)' of myeongbal means to make a sound, and thus myeongbal refers to clash and make the sound of the bara. It is verified that myeongbal had certain established rules and methods. It appears that dongbal(動鈸) refers to Baramu(the cymbals dance) since the letter 'dong(動)' means movement or to move. Hence, the concept of movement was added to the signification of myeongbal, and became dongbal(動鈸), and then developed into baramu being transmitted until today. There are 8 types of Baramu transmitted in Korean Buddhist rituals, and they could be classified into purifying ritual, inviting ritual, protecting ritual, offering ritual, bathing ritual, dressing ritual, saluting ritual, and praising ritual according to their attributes.
Background: This study aims to develop a "Predictive Model for the Possibility of Collection Delinquent Health Insurance Contributions" for the National Health Insurance Service to enhance administrative efficiency in protecting and collecting contributions from livelihood-type defaulters. Additionally, it aims to establish customized collection management strategies based on individuals' ability to pay health insurance contributions. Methods: Firstly, to develop the "Predictive Model for the Possibility of Collection Delinquent Health Insurance Contributions," a series of processes including (1) analysis of defaulter characteristics, (2) model estimation and performance evaluation, and (3) model derivation will be conducted. Secondly, using the predictions from the model, individuals will be categorized into four types based on their payment ability and livelihood status, and collection strategies will be provided for each type. Results: Firstly, the regression equation of the prediction model is as follows: phat = exp (0.4729 + 0.0392 × gender + 0.00894 × age + 0.000563 × total income - 0.2849 × low-income type enrollee - 0.2271 × delinquency frequency + 0.9714 × delinquency action + 0.0851 × reduction) / [1 + exp (0.4729 + 0.0392 × gender + 0.00894 × age + 0.000563 × total income - 0.2849 × low-income type enrollee - 0.2271 × delinquency frequency + 0.9714 × delinquency action + 0.0851 × reduction)]. The prediction performance is an accuracy of 86.0%, sensitivity of 87.0%, and specificity of 84.8%. Secondly, individuals were categorized into four types based on livelihood status and payment ability. Particularly, the "support needed group," which comprises those with low payment ability and low-income type enrollee, suggests enhancing contribution relief and support policies. On the other hand, the "high-risk group," which comprises those without livelihood type and low payment ability, suggests implementing stricter default handling to improve collection rates. Conclusion: Upon examining the regression equation of the prediction model, it is evident that individuals with lower income levels and a history of past defaults have a lower probability of payment. This implies that defaults occur among those without the ability to bear the burden of health insurance contributions, leading to long-term defaults. Social insurance operates on the principles of mandatory participation and burden based on the ability to pay. Therefore, it is necessary to develop policies that consider individuals' ability to pay, such as transitioning livelihood-type defaulters to medical assistance or reducing insurance contribution burdens.
The difficulties of satellite vibration testing are due to the commonly expressed qualification requirements being incompatible with the limited performance of the entire controlled system (satellite + interface + shaker + controller). Two features cause the problem: firstly, the main satellite modes (i.e., the first structural mode and the high and low tank modes) are very weakly damped; secondly, the controller is just too basic to achieve the expected performance in such cases. The combination of these two issues results in oscillations around the notching levels and high amplitude beating immediately after the mode. The beating overshoots are a major risk source because they can result in the test being aborted if the qualification upper limit is exceeded. Although the abort is, in itself, a safety measure protecting the tested satellite, it increases the risk of structural fatigue, firstly because the abort threshold has been already reached, and secondly, because the test must restart at the same close-resonance frequency and remain there until the qualification level is reached and the sweep frequency can continue. The beat minimum relates only to small successive frequency ranges in which the qualification level is not reached. Although they are less problematic because they do not cause an inadvertent test shutdown, such situations inevitably result in waiver requests from the client. A controlled-system analysis indicates an operating principle that cannot provide sufficient stability: the drive calculation (which controls the process) simply multiplies the frequency reference (usually called cola) and a function of the following setpoint, the ratio between the amplitude already reached and the previous setpoint, and the compression factor. This function value changes at each cola interval, but it never takes into account the sensor signal phase. Because of these limitations, we firstly examined whether it was possible to empirically determine, using a series of tests with a very simple dummy, a controller setting process that significantly improves the results. As the attempt failed, we have performed simulations seeking an optimum adjustment by finding the Least Mean Square of the difference between the reference and response signal. The simulations showed a significant improvement during the notch beat and a small reduction in the beat amplitude. However, the small improvement in this process was not useful because it highlighted the need to change the reference at each cola interval, sometimes with instructions almost twice the qualification level. Another uncertainty regarding the consequences of such an approach involves the impact of differences between the estimated model (used in the simulation) and the actual system. As limitations in the current controller were identified in different approaches, we considered the feasibility of a new controller that takes into account an estimated single-input multi-output (SIMO) model. Its parameters were estimated from a very low-level throughput. Against this backdrop, we analyzed the feasibility of an LQG control in cancelling beating, and this article highlights the relevance of such an approach.
Journal of the Korean Recycled Construction Resources Institute
/
v.7
no.4
/
pp.71-78
/
2012
Recycled aggregates are made from construction wastes, and they have many national and social benefits by saving energy, developing substitute resources, and protecting environment. However, low-quality recycled aggregate with low density and high absorption rate cannot be used for structural concrete aggregate but is used mainly for low added value. Therefore, this study aims to identify the characteristics of the materials of recycled aggregates made after crashing and pulverizing waste concrete. For this, their major physical characteristics of cement content, absolute dry density, absorption rate, etc. were reviewed to make a mix design (draft) for the production of the secondary product and performance evaluation was done on the bending strength, absorption rate, bending strength after freezing and thawing, compressive strength, air-dried gravity, etc. of the test products produced by applying the mix design to compare the results with the quality standards of GR mark. The results of the tests showed that the substitution rate of recycled aggregate increased to 50~90 %, which is of superior quality than the performance standards of GR F 4007. Therefore, it is thought that they can be used for various construction works with certain physical characteristics applicable to the production of secondary concrete products using recycled aggregates.
Seo, Jihye;Lee, Byung-Wook;Park, Woo-Sun;Won, Deokhee
Journal of Korean Society of Coastal and Ocean Engineers
/
v.30
no.1
/
pp.10-18
/
2018
Recently, a port city has been gradually expanding near coastal area, and many facilities for tourism and waterfront have been constructed near the shore. When storm surge developed by typhoon have occurred, coastal facilities have a lot of damage and failure with loss of life caused directly by the waves. Various barriers have been suggested to protect property and human life from disasters, they have not been widely applied though. Because they do not satisfy the recent trends that emphasize the surrounding scenery. In this study, a moveable barrier on revetment is proposed against wave overtopping. This moveable barrier has two function, sightseeing and protecting. In case of usual day, it is installed on the revetment and used observatory deck for sightseeing. When wave overtopping has occurred by storm surge, it protect coastal area through changing of flat deck to triangular barrier. The hydraulic and the structural performance of the newly proposed movable barrier was investigated through numerical analysis using commercial program. As a results, this structure has numerically good performance, and follow-up research is required through experimental tests though.
It is a trend to increase safekeeping properties in financial company as the world economy situation has been globalized and advanced. The development of a securable vault door resisting to malicious trespass is needed. Therefore, this study focuses on developing high performance concrete placed at the inside of the vault door, and all materials used in this study is easy to obtain in domestic considering economic competitiveness. The compressive strength over 170 MPa was targeted, and structurally strengthening was also planned in order to resist to over $3,000^{\circ}C$ heating by torch and extreme impact loading by hammer drilling machine. Several types of fibers and reinforcing structures were used in order to resist those external heating and loading. This purpose was required to satisfy UL 608 standard of a vault door. Consequently, the result from this study is expected to be applied to construction field of major facilities, which should guarantee the safety from an external attack such as terror.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.