• Journal of the Korean Electrochemical Society
• /
• v.10 no.4
• /
• pp.301-305
• /
• 2007

The performance of polymer electrolyte membrane fuel cell could be decreased due to coolant leaked from connection part. Micro pump was used to put small amount of coolant and investigate the effect on fuel cell. The stoichiometric ratio of hydrogen/air was 1.5/2.0, both side of gas was fully humidified, and current density of $400mA/cm^2$ was used as standard condition in this experiment. Constant current method was used to check performance recovery from coolant effect in 3 cell stack. The performance was recovered when coolant was injected in cathode side. On the other hand, the performance was not recovered when coolant was injected in anode side. Ethylene glycol could be converted to CO in oxidation process and cause poisoning effect on platinum catalyst or be adhered on GDL and cause gas diffusion block effect resulting performance decrease. Water with nitrogen gas was supplied in anode side to check performance recovery. Polarization curve, cyclic voltammetry, electrochemical impedance spectroscopy was used to check performance, and gas chromatography was used to check coolant concentration. Constant current method was not enough in full recovery of performance. However, water injection method was proved good method in full recovery of performance.

• Journal of the Korea Concrete Institute
• /
• v.13 no.1
• /
• pp.9-15
• /
• 2001

The low-durability performance of concrete structure occurs by interactive deterioration factors. In particular, carbonation increased with its time elapse is known as the general manner of deterioration characteristics. Recently, the fundamental researches of the carbonation mechanism, besides method and technique for durability improvement of deteriorated structure are advanced actively. So in this paper, alkali-recovery and maintenance performance when the impregnating alkalization agents are used, are compared and examined quantitively with the basis of past proposed study. As a result, alkali-recovery performance be ensured by impregnating alkalization agent on the carbonated concrete which has low pH by accelerated carbonation test. And alkali maintenance performance was effected by the finishing materials on the alkali recovered concrete.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.584-597
• /
• 2016

This paper focuses on an improvement in the transient performance of Boost converters when the load changes abruptly. This is achieved on the basis of the nature trajectory in Boost converters. Three key aspects of the transient performance are analyzed including the storage energy change law in the inductors and capacitors of converters during the transient process, the ideal minimum voltage deviation in the transient process, and the minimum voltage deviation control trajectory. The changing relationship curve between the voltage deviation and the recovery time is depicted through analysis and simulations when the load suddenly increases. In addition, the relationship curve between the current fluctuation and the recovery time is obtained when the load suddenly decreases. Considering the aspects of an increasing and decreasing load, this paper proposes the transient performance synthetic optimized trajectory and control laws. Through simulation and experimental results, the transient performances are compared with the other typical three control methods, and the ability of proposed synthetic trajectory and control law to achieve optimal transient performance is verified.

• Journal of Biosystems Engineering
• /
• v.5 no.2
• /
• pp.1-14
• /
• 1980

This study was carried out to investigate the effects of the counter-pressure setting and the roller speed of a rice whitening machine on the head rice recovery. milling capacity and milling efficiency, and also to find out the optimum operational conditions of the machine. The radial pressure inside the whitening chamber and the outlet axial pressure were measured to study their relationships with the head rice recovery, milling capacity and milling efficiency. The results of the study are summarized as follows. (1) The most important factor in rice whitening was the counter-pressure setting. It significantly affected the head rice recovery. (2) The roller speed significant affected the milling capacity and milling efficiency , but it did not affected the head rice recovery. (3) Both the radial pressure and the outlet axial pressure were affected by the counter-pressure setting but not by the roller speed. Both of them increased almost linearly with the counter-pressure setting. There was a significant correlation between the radial pressure and the outlet axial pressure. (4) The flow rate through the whitening chamber when the feed gate was fully opened increased with the roller speed, but it was not affected by the counter-pressure setting. (5) The head rice recovery decreased as the counter-pressure setting increased , but it was not affected by the roller speed. The reason could be explained by the fact that the radical pressure increased only with the counter-pressure setting. (6) The milling capacity increased with the counter-pressure setting and linearly with the roller speed. The milling efficiency generally increased with both the counter-pressure setting and the roller speed. However, the effect of roller speed was negligible at the higher counter-pressure setting. The temperature rise inside the whitening chamber was moderate with the mean of 11.3℃ (range 5.6-18.3℃) even though it increased slightly with the roller speed. Considering the head rice recovery and milling efficiency, the optimum operational conditions of the machine appeared to be the counter-pressure setting of 67g/㎠ and the roller speed of 1,050rpm. Neglecting the small difference in the head rice recovery , the greater milling capacity could be obtained at the counter-pressure setting of 85g/㎠ with the roller speed of 850-1050rpm.

• The KIPS Transactions:PartC
• /
• v.9C no.4
• /
• pp.589-596
• /
• 2002

Tn the data transmission service of the mobile host, it is needed to reduce the bandwidth and to make a reliable error recovery. there are two appropriate methods in that. One is FEC which retransmits the parity of error recovery, in case of happening of the loss after forming the parity of error recovery by grouping original data. The other is local recovery based on server which can block the implosion of transmission. The use of FEC and local recovery based on server at the same time enables the reliable multicast. This paper suggests algorithm that recovers the loss by FEC and local recovery based on server through the solution of the problems about triangle routing, tunnel convergence by dividing mobile host into two parts-the sender and the receiver. This model about the loss of algorithm tested the efficiency of performance by the homogeneous independent loss, the heterogeneous independent loss, the shared source link loss model. The suggested algorithm confirms effectiveness in the environment where there are much data and many receivers in mobile host.

• Korean Journal of Clinical Laboratory Science
• /
• v.38 no.3
• /
• pp.184-188
• /
• 2006

The purpose of the recovery experiment in clinical chemistry is performed to estimate proportional systematic error. We must know all measurements have some error margin in measuring analytical performance. Proportional systematic error is the type of error whose magnitude increases as the concentration of analyte increases. This error is often caused by a substance in the sample matrix that reacts with the sought for analyte and therefore competes with the analytical reagent. Recovery experiments, therefore, are used rather selectively and do not have a high priority when another analytical method is available for comparison purposes. They may still be useful to help understand the nature of any bias revealed in the comparison of kit experiments. Recovery should be expressed as a percentage because the experimental objective is to estimate proportional systematic error, which is a percentage type of error. Good recovery is 100.0%. The difference between 100 and the observed recovery(in percent) is the proportional systematic error. We calculated the amount of analyte added by multiplying the concentration of the analyte added solution by the dilution factor(mL standard)/(mL standard + mL specimen) and took the difference between the sample with addition and the sample with dilution. When making judgments on method performance, the observed that the errors should be compared to the defined allowable error. The average recovery needs to be converted to proportional error(100%/Recovery) and then compared to an analytical quality requirement expressed in percent. The results of recovery experiments were total protein(101.4%), albumin(97.4%), total bilirubin(104%), alkaline phosphatase(89.1%), aspartate aminotransferase(102.8), alanine aminotransferase(103.2), gamma glutamyl transpeptidase(97.6%), creatine kinase(105.4%), lactate dehydrogenase(95.9%), creatinine(103.1%), blood urea nitrogen(102.9%), uric acid(106.4%), total cholesterol(108.5), triglycerides(89.6%), glucose(93%), amylase(109.8), calcium(102.8), inorganic phosphorus(106.3%). We then compared the observed error to the amount of error allowable for the test. There were no items beyond the CLIA criterion for acceptable performance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.12
• /
• pp.756-763
• /
• 2014

In this paper, we introduce a new sparse signal recovery algorithm referred to as the matching pursuit with greedy tree search (GTMP). The tree search in our proposed method is implemented to minimize the cost function to improve the recovery performance of sparse signals. In addition, a pruning strategy is employed to each node of the tree for efficient implementation. In our performance guarantee analysis, we provide the condition that ensures the exact identification of the nonzero locations. Through empirical simulations, we show that GTMP is effective for sparse signal reconstruction and outperforms conventional sparse recovery algorithms.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.10
• /
• pp.4835-4855
• /
• 2018

In this paper, we study the sparse signal recovery that uses information of both support and amplitude of the sparse signal. A convergent iterative algorithm for sparse signal recovery is developed using Majorization-Minimization-based Non-convex Optimization (MM-NcO). Furthermore, it is shown that, typically, the sparse signals that are recovered using the proposed iterative algorithm are not globally optimal and the performance of the iterative algorithm depends on the initial point. Therefore, a modified MM-NcO-based iterative algorithm is developed that uses prior information of both support and amplitude of the sparse signal to enhance recovery performance. Finally, the modified MM-NcO-based iterative algorithm is used to estimate the time-varying sparse wireless channels with temporal correlation. The numerical results show that the new algorithm performs better than related algorithms.

• Journal of KIISE
• /
• v.42 no.11
• /
• pp.1452-1458
• /
• 2015

Korean Morphological Analysis is a difficult process. Because Korean is an agglutinative language, one of the most important processes in Morphological Analysis is Morpheme Recovery. There are some methods using Heuristic rules and Pre-Analyzed Partial Words that were examined for this process. These methods have performance limits as a result of not using contextual information. In this study, we built a Korean morpheme recovery system using deep learning, and this system used word embedding for the utilization of contextual information. In '들/VV' and '듣/VV' morpheme recovery, the system showed 97.97% accuracy, a better performance than with SVM(Support Vector Machine) which showed 96.22% accuracy.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.45 no.2
• /
• pp.335-345
• /
• 2021

The purpose of this study was to examine the effect of fabric movement on wrinkle recovery in a clothing care system and to propose an algorithm to improve wrinkle removal performance by adjusting fabric movements. With an increase in the reciprocating speed of the movement system, the number and amplitude of curves on the fabric also increased. This allowed the fabric to be applied to a larger tension, resulting in better wrinkle removal performance at higher speeds. However, even at high reciprocating speeds, wrinkles could not be removed effectively because of nodes at a few specific locations. Based on the results of fabric movement and wrinkle recovery, a complex movement algorithm was proposed with a mixture of various reciprocation speeds. It showed a 41%p (24%→65%) improvement of wrinkle recovery when compared with the conventional algorithm that showed simple fabric movement at 180 rpm. This was because the positions of nodes and antinodes changed continuously and the force by the reciprocating motion could be applied evenly to the fabric.