• Food Science and Biotechnology
• /
• v.15 no.4
• /
• pp.631-634
• /
• 2006

Soy protein isolate (SPI) films were supplemented with cinnamaldehyde (CA) at concentrations of 0.1-0.5 mL/5 g SPI. The effects of CA on film color, tensile strength (TS), percent elongation at break (E, %) and water vapor permeability (WVP) of SPI films were investigated. Generally, total color difference (${\Delta}E$), WVP, and TS of SPI films increased gradually, while E and TSM decreased significantly (p<0.05) as the amount of cinnamaldehyde in the SPI films increased. Cinnamaldehyde can be used as a potential cross-linking agent for preparing SPI films by improving mechanical strength and water resistant properties.

• Korean Journal of Food Science and Technology
• /
• v.29 no.2
• /
• pp.255-260
• /
• 1997

Glucomannan was isolated from konjac (Amorphophallus konjac) flour by precipitating in aqueous alcohol solution. Konjac glucomannan films were prepared at various concentrations up to 1.0% (w/v) in aqueous glycerol solutions. Tensile strength (TS), percent elongation (E), water vapor permeability (WVP) as the barrier property and the solubility of the films were varied with glucomannan concentrations, glycerol contents and storage humidities. TS was decreased as the glucomannan concentration in the film and relative humidity for storage increased, and E was vice versa. WVP showed better barrier properties compared with other polysaccharides films. Glycerol contents in the film significantly affccted TS and E, but did not affect WVP. The glucomannan films were completely dissolved in the water by 150 min stirring at room temperature.

• Korean Journal of Materials Research
• /
• v.4 no.5
• /
• pp.556-565
• /
• 1994

Effects of Ag addition to 2090 and CP 276 Al-Li alloy systems on the microstructure and mechanical properties have been investigated. The addition of silver up to 0.16wt.% reduced the grain size of the alloys, and was responsible for the formation of finer and more uniform $\delta$'($AI_{3}Li$) and $T_{1}(AI_{2}CuLi$) precipitates in 2090 alloys, even though no variation of precipitates was found in CP 276 alloys. The addition of 0.16wt.% Ag improved the tensile strength of 2090 alloys about 40MPa with the expense of small reduction of percent elongation. However, the small addition of Ag to CP 276 containing Mg did not show any variation of tensile strength and elongation. The aging treatment of these alloys at $150^{\circ}C$ for 70 or 90 hours, depending on alloy systems, showed peak hardness value of about 92 $H_rB$.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.31 no.1
• /
• pp.56-61
• /
• 1986

Germination and seedling elongation of maize (Dekalb XL 72B), and soybeans (Williams) were measured at two temperatures (15 and 35$^{\circ}C$), three soil water potentials (-1.50, -0.5, and -0.05 MPa), and four polyethy-lene glycol 8000 (PEG) levels (0, 20, 30, and 50 percent). Twenty conditioned seeds of each cultivar were treated with 0.2% thiram and planted 2 cm deep in sterilized Mexico silt loam soil which was subsequently compacted to a bulk density of 1.20 g/㎤. Seedling moisture content, dry weight, and length were measured for each treatment combination. Osmoconditioning with PEG showed little effect at high temperature or low soil water potential conditions. Soybeans had higher seedling moisture content than corn and both crops in-creased moisture uptake as soil water potential and temperature increased. Seedling length of corn was longer than soybeans at 35$^{\circ}C$ but shorter at 15$^{\circ}C$. Seedling dry weight of corn decreased at 35$^{\circ}C$ and that of soybeans decreased as soil water potential increased.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.38 no.2
• /
• pp.174-182
• /
• 1993

Performance of 3 indica ${\times}$ japonica(Chilseungbyeo, Samgangbyeo, and Gayabyeo), 7 japonica(Yeongsanbyeo, Yeongdeugbyeo, Hwajinbyeo, Palgongbyeo, Seumjinbyeo, Tamjinbyeo, and Milyang 95), and 2 indica(Tebonnet and Lemont) rice varieties was tested at 1, 3, 5, and 7cm seeding depths in a growth chamber and field. In the growth chamber the number of days from seeding to seedling emergence increased as seeding depth increased, while percent germination and emergence and emergence / germination ratio decreased. However, in the field seedling emergence at 1em seeding depth delayed slightly compared to 3cm probably due to lack of soil moisture. The number of seedlings and maximum tillers at 1, 3, and 5cm seeding depths was similar, but it was higher compared to 7cm seeding depth. Yield and yield components were similar among the seeding depths when all the varieties averaged although 1,000-grain weight was slightly higher at 7cm deeding depth compared to others. At 1cm seeding depth the length of mesocotyl of all varieties was similar and ranged 0.1-0.2cm and that of coleptile ranged 0.8-1.1cm. As seeding depth increased up to 7cm Tebonnet which showed the highest percent emergence emerged by elongation of both mesocotyl and coleoptile, while the other varieties emerged largely by elongation of coleoptile.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.5
• /
• pp.819-824
• /
• 2016

The accelerated thermal aging of CSPE (chlorosulfonated polyethylene) was carried out for 33.64 and 67.27 days at 110[$^{\circ}C$], equivalent to 40 and 80 years of aging at 50[$^{\circ}C$], respectively. These samples were referred to as CSPE-0y, CSPE-40y and CSPE-80y, respectively. As the accelerated thermally aged years of the CSPE increase, the insulation resistance[$\Omega$] at 20[Hz], 500[Hz], and 2[KHz], and the percent elongation [%EL] of the CSPE decrease. However, the dissipation factor($tan{\delta}$) at 20[Hz], 500[Hz], and 2[KHz], the apparent density[$g/cm^3$], the glass transition temperature and the melting temperature of the CSPE were increased. The period of time that the voltage has to be applied until electric breakdown of the CSPE-0y is longer than that of the CSPE-40y, and the CSPE-80y, but the dielectric strength of the CSPE-80y is lower than that of the CSPE-0y and the CSPE-40y. The differential temperatures after the AC and DC voltages are applied to CSPE-0y, CSPE-40y and CSPE-80y are 0.026~0.028[$^{\circ}C$], 0.030~0.042[$^{\circ}C$], 0.018~0.045[$^{\circ}C$], respectively. The variations of temperature for the AC voltage are higher than those for the DC voltage when an AC voltage is applied to CSPE-0y, CSPE-40y and CSPE-80y. It is found that the dielectric loss owing to the dissipation factor[$tan{\delta}$] is related to the electric dipole conduction current. It is ascertained that the ionic (electron or hole) leakage current is increased by the separation of the branch chain of CSPE polymer from the main chain of the polyethylene as a result of thermal stress due to accelerated thermal aging as well as by conducting ions such as $Na^+$, $Cl^-$, $Mg^{2+}$, $SO_4^{2-}$, $Ca^{2+}$ and $K^+$ after seawater soaking.

• Resources Recycling
• /
• v.24 no.2
• /
• pp.36-45
• /
• 2015

In this study, various sizes of waste ground rubber tire (WGRT) were devulcanized by a single screw extruder equipped with a sonicator in front of the die, and waste PP and devulcanized waste ground rubber tire (DWGRT) composites were prepared by an intermeshing co-rotating twin screw extruder. The crosslink density and percent devulcanization of WGRT and DWGRT for 40, 80 and 140 meshes were calculated. The mechanical properties of the composites were compared with each other. The effect of SEBS-g-MA as a compatibilizer was investigated on mechanical properties of both waste PP/WGRT and waste PP/DWGRT composites. The crosslink density was decreased with decreasing the WGRT size. On the other hand, the percent devulcanization was increased by adding the smaller size of WGRT. Also, tensile strength, impact strength and elongation at break of the composite with DWGRT were higher than those with WGRT. Especially, mechanical properties of the composites were significantly increased by adding the smaller size of WGRT and DWGRT. Addition of SEBS-g-MA into both waste PP/(D)WGRT composites exhibited better impact strength and elongation at break than the composites themselves.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.35 no.1
• /
• pp.121-125
• /
• 2006

To study the effects of plasticizer concentration and its ratio on the physical properties of silk fibroin films, polyethylene glycol (PEG) was used at 4 different concentrations; 1, 2, 3, $4.5\%$ (w/v). Tensile strength (TS) and water vapor permeability (WVP) increased with the increase of PEG concentration, while opposite trend was observed for percent elongation of silk fibroin films. WVP of silk fibroin films increased from $2.54\;ng{\cdot}m/m^2spa$ for $1\%$ of PEG to $5.41\;ng{\cdot}m/m^2sPa$ for $4.5\%$. In addition, a mixture of PEG and glycerol (Gly) as a plasticizer was used at the ratio of 100:0, 75:25, 50:50, 25:75, and 0:100 (w/w). Percent elongation of the films was improved to $130.95\%$ when the ratio of 75:25 was used. On the contrary, WVP of silk fibroin films increased with the decrease of the ratio of PEG:Gly. Effect of the plasticizer concentration and its ratio on the color of silk fibroin films was negligible. These results suggest that mixture of PEG and Gly as a plasticizer provide more flexible than PEG alone in silk fibroin films, and the best ratio of PEG to Gly was 75:25.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.32 no.1
• /
• pp.61-66
• /
• 1987

Germination and seedling length of soybean seeds (cultivar: Williams) with and without polyethylene glycol-8000 (PEG) treatments were measured following preconditioning at two temperatures (15 and 30$^{\circ}C$) and two moisture levels 〔low (30 percent) and high (50 percent seed water content)〕 for 0, 2, 4, or 8 days. A split-split plot in time was used with four replications. Observations were made after two days of germination at 30$^{\circ}C$ Seedling growth accelerated with two days of preconditioning at 30$^{\circ}C$, but was reduced as preconditioning duration increased up to eight days at the same temperature. PEG treated preconditioned seeds exhibited reduced moisture uptake and seedling growth. Preconditioning at a high moisture level increased seedling moisture content and also increased seedling length until four days of preconditioning duration. Seedling dry weight decreased when preconditioning temperature was 30$^{\circ}C$ and when the high moisture level of preconditioning was continued for eight days.

• Korean Journal of Weed Science
• /
• v.14 no.4
• /
• pp.252-257
• /
• 1994

The sprouting characteristics of Scirpus planiculmis and storage methods of corm for the herbicide screening were investigated under both laboratory and greenhouse conditions. Sprouting and elongation of S. planiculmis corms were continued during storage at low temperature ($5^{\circ}C$) and wet condition. However, sprouting of corm was failed when the surface water was removed from the corm, and elongation was reduced by the treatment of 0.5-1.0% sodium chloride(NaCl) solution. Alternate temperature was more effective on the sprouting of S. planiculmis corm than constant temperature. Optimum temperature for the sprouting of S. planiculmis corm was alternation between $25^{\circ}C$ to $35^{\circ}C$. Storage at $-20^{\circ}C$ for 10 min. or 14.7% dehydration made the corm of S. planiculmis to fail for sprouting. S. planiculmis corm was more tolerant to sodium chloride than Echinochloa crus-galli or Oryza sativa(Donginbyeo) seeds. Sprouting rate was decreased by cutting of the corm. Sprouting percent by vertical cuttings, horizontal cuttings, and vertical plus horizontal cuttings were 72, 56, and 28%, respectively.