• 대한의용생체공학회:의공학회지
• /
• 제25권5호
• /
• pp.383-389
• /
• 2004

본 연구에서는 치과용 티타늄(CP-Ti)과 Ti-25wt%Pd를 인산염계 실리카$.$알루미나 주형재로 주조 후 SEM/EDS, XRD, XPS를 이용하여 주조시 생성되는 표면반응생성물을 조사하였다. Ti-25wt%Pd는 CP-Ti에 비하여 융점이 현저이 감소하여 주조체의 표면반응이 상대적으로 적게 발생하였다. 또한 인산염계 실리카$.$알루미나 주형재를 소성한 결과 주형재는 $SiO_2$, $Al_2$ $O_3$, P$_2$ $O_{5}$, $Mg_3$(P $O_4$)$_2$, AlP $O_4$, $Mg_2$ $SiO_4$, MgAl$_2$ $O_4$의 성분들로 구성되어 있었으며, 표면반응생성물은 CP-Ti 주조체의 경우 $Ti_{5}$Si$_3$ 와 Ti $O_2$로, Ti-25wt%Pd 주조체의 경우 Ti $O_2$ 와 $SiO_{x}$ 로 구성되어 있었다.

• 한국가스학회지
• /
• 제20권2호
• /
• pp.1-9
• /
• 2016

본 연구는 플라즈마/촉매 공정을 이용하여 n-헵테인과 일산화탄소의 동시제거에 대해 조사하였다. n-헵테인과 일산화탄소의 분해특성을 파악하기 위해 플라즈마/촉매 공정과 촉매공정의 분해효율을 비교하였고, 촉매의 종류, 온도, 전력 등을 변화시켜 실험을 진행하였다. n-헵테인의 분해효율은 반응기 내부의 온도보다는 에너지밀도에 더 영향을 많이 받는 것으로 확인되었으며, 일산화탄소는 에너지밀도와 반응기 내부 온도 모두의 영향을 받는 것으로 나타났다. 촉매의 종류를 달리하며 n-헵테인의 분해효율을 조사한 결과 $Pd/{\gamma}-Al_2O_3$ > $Ru/{\gamma}-Al_2O_3{\approx}Ag/{\gamma}-Al_2O_3$순으로 나타났다. 특히, $Pd/{\gamma}-Al_2O_3$를 사용한 경우 n-헵테인 분해 과정에서 일산화탄소가 거의 발생하지 않았으며, $CO_2$ 선택도가 100%에 가까웠다. 일산화탄소 분해효율은 $Pd/{\gamma}-Al_2O_3$ > $Ru/{\gamma}-Al_2O_3$ > $Ag/{\gamma}-Al_2O_3$ 순으로 나타났으며, $180^{\circ}C$이하의 온도에서는 플라즈마/촉매 공정의 효율이 높고, $180^{\circ}C$이상에서는 촉매 공정의 분해효율이 높았다.

• 한국자기학회지
• /
• 제11권3호
• /
• pp.109-113
• /
• 2001

Presently, an inductor adapted at MMIC (Monolithic Microwave Integrated Circuit) which is used for cellular phone or PHS operates at quasi-microwave range over 800 MHz. However, a W-CDMA (Wideband Code Division Multiple Access) will use about 2 GHz range. Therefore magnetic film device should be compatible up to 2 GHz. We have deposited Co-Pd-Al-O system film using rf sputtering method which is expected up to 2 GHz, and investigated the effect of Pd content and magnetic field annealing. When Pd composition is 19%, Hk was 118 Oe, and ${\mu}$′showed flat frequency characteristics up to 1.5 GHz. The Q factor (=${\mu}$′/${\mu}$") was 23.3 at 1 GHz, 6.7 at 1.5 GHz and 1.5 at 2 GHz, respectively. Resonance frequency was 2 GHz. Therefore Co-Pd-Al-O thin film could be used at over 1 GHz, and also expected as an inductor material for wide band CDMA type cellular phone.

• Environmental Engineering Research
• /
• 제10권3호
• /
• pp.131-137
• /
• 2005

The catalytic activity of precious metals(Rh, Pd, Pt) and nickel catalysts supported on ${\gamma}-Al_2O_3\;and\;CeO_2$ in the partial combustion of methane(PCM) to syngas was investigated based on the product distribution in a fixed bed now reactor under atmospheric condition and also on analysis results by SEM, XPS, TPD, BET, and XRD. The activity of the catalysts based on the syngas yield increased in the sequence $Rh(5)/CeO_2{\geq}Ni(5)/CeO_2>>Rh(5)/Al_2O_3>Pd(5)/Al_2O_3>Ni(5)/Al_2O_3$. Compared to the precious catalysts, the syngas yield and stability of the $Ni(5)/CeO_2$ catalyst were almost similar to $(5)/CeO_2$ catalyst, and superior to these of any other catalysts. The syngas yield of $Ni(5)/CeO_2$ catalyst was 90.66% at 1023 K. It could be suggested to be the redox cycle of the successive reaction and formation of active site, $Ni^{2-}$ and the lattice oxygen, $O^{2-}$ produced due to reduction of $Ce^{4-}$ to $Ce^{3-}$.

• Bulletin of the Korean Chemical Society
• /
• 제31권1호
• /
• pp.120-124
• /
• 2010

Monometallic, bimetallic and trimetallic particles consisting of different weight compositions of Pt-Pd-Rh over pure alumina wash coats have been synthesized and their catalytic performance on methane conversion was studied from 150 to $600^{\circ}C$. Different catalyst formulations with variable Pt, Pd and Rh contents for bimetallic and trimetallic systems were tried and $Pt_{(1.5)}Rh_{(0.3)}/Al_2O_3$ and $Pt_{(1.0)}Pd_{(1.0)}Rh_{(0.3)}/Al_2O_3$ shows low $T_{50}$ and $T_{90}$ temperatures. Bimetallic and trimetallic particle synergism acts as three way catalysts and therefore, all the catalysts show 100% methane conversion. The effect of supports such as $ZrO_2$ and $TiO_2$ on methane combustion was investigated; from $T_{50}$ and $T_{90}$ results both $Al_2O_3$ and $ZrO_2$ are suitable supports for low temperature methane combustion.

• 한국세라믹학회지
• /
• 제22권4호
• /
• pp.54-60
• /
• 1985

Gas sensing materials for detecting flammable gases such as $CH_4$, $C_3H_8$ and n-$C_4H_{10}$ were developed by util-izing $In_2O_3$ as the principal sensing material. The sensing materials were formulated by mixing $In_2O_3$ powder with one or two other chemicals such as $SnO_2$, $Y_2O_3$ and $Al_2O_3$ with a small addition of $PdCl_2$ as a catalyst. Sample of sensor were fabricated by coating each of the mixtures on a ceramic tube impregnating ethylsili-cate and firing at 75$0^{\circ}C$ Each material mixture was evaluated by measuring and comparing gas sensitivity(resistance in air/resistance with gas) to flammable gases such as $CH_4$, $C_3H-8$ and n-$C_4H_{10}$. It was found that among fifteen compositions tested three compositions as follows show the highest gas sensitivity and thus are very feasible for commercialization as the gas sensors ; o49.5 $In_2O_3$+50 Al2O3_0.5 PdCl2(wt%) o $20In_2O_3+29$ $SnO_2+50$ $Al_2O_3+1$ $PdCl_2$(wt%) o40 $In_2O_3$+9 $Y_2O_3+50$ $Al_2O_3+1$ $PdCl_2$(wt%)

• Bulletin of the Korean Chemical Society
• /
• 제24권12호
• /
• pp.1771-1774
• /
• 2003

CNTs have been synthesized by catalytic $C_2H_2$ decomposition through $Pd/Al_2O_3$ at low temperature. The CNTs were grown to a length of about 10 ${\mu}$m and diameter 150-200 nm with multiwalled structure. Pd catalysts have two major roles; one is the active catalyst for $C_2H_2$ decomposition, the other is a nucleation site of CNT's growth.

• Bulletin of the Korean Chemical Society
• /
• 제22권1호
• /
• pp.30-36
• /
• 2001

The crystal structures of fully dehydrated $Pd^{2+}$ - and $TI^{+}$ -exchanged zeolite X, $Pd_{18}TI_{56}Si_{100}Al_{92}O_{384}(Pd_{18}TI_{50-}X$, a = $24.935(4)\AA$ and $Pd_{21}TI_{50}Si_{100}Al_{92}O_{384}(Pd_{21}TI_{50-}X$ a = $24.914(4)\AA)$, have been determined by single-crystal X-ray diffraction methods in the cubic space group Fd3 at $21(1)^{\circ}C.$ The crystals were prepared using an exchange solution that had a $Pd(NH_3)_4Cl_2\;:TINO_3$ mole ratio of 50 : 1 and 200 : 1, respectively, with a total concentration of 0.05M for 4 days. After dehydration at $360^{\circ}C$ and 2 ${\times}$$10^{-6}$ Torr in flowing oxygen for 2 days, the crystals were evacuated at $21(1)^{\circ}C$ for 2 hours. They were refined to the final error indices $R_1$ = 0.045 and $R_2$ = 0.038 with 344 reflections for $Pd_{18}Tl_{56-}X$, and $R_1$ = 0.043 and $R_2$ = 0.045 with 280 reflections for $Pd_{21}Tl_{50-}X$; I > $3\sigma(I).$ In the structure of dehydrated $Pd_{18}Tl_{56-}X$, eighteen $Pd^{2+}$ ions and fourteen $TI^{+}$ ions are located at site I'. About twenty-seven $TI^{+}$ ions occupy site II recessed $1.74\AA$ into a supercage from the plane of three oxygens. The remaining fifteen $TI^{+}$ ions are distributed over two non-equivalent III' sites, with occupancies of 11 and 4, respectively. In the structure of $Pd_{21}Tl_{50-}X$, twenty $Pd^{2+}$ and ten $TI^{+}$ ions occupy site I', and one $Pd^{2+}$ ion is at site I. About twenty-three $TI^{+}$ ions occupy site II, and the remaining seventeen $TI^{+}$ ions are distributed over two different III' sites. $Pd^{2+}$ ions show a limit of exchange (ca. 39% and 46%), though their concentration of exchange was much higher than that of $TI^{+}$ ions. $Pd^{2+}$ ions tend to occupy site I', where they fit the double six-ring plane as nearly ideal trigonal planar. $TI^{+}$ ions fill the remaining I' sites, then occupy site II and two different III' sites. The two crystal structures show that approximately two and one-half I' sites per sodalite cage may be occupied by $Pd^{2+}$ ions. The remaining I' sites are occupied by $TI^{+}$ ions with Tl-O bond distance that is shorter than the sum of their ionic radii. The electrostatic repulsion between two large $TI^{+}$ ions and between $TI^{+}$ and $Pd^{2+}$ ions in the same $\beta-cage$ pushes each other to the charged six-ring planes. It causes the Tl-O bond to have some covalent character. However, $TI^{+}$ ions at site II form ionic bonds with three oxygens because the super-cage has the available space to obtain the reliable ionic bonds.

• 센서학회지
• /
• 제1권2호
• /
• pp.107-116
• /
• 1992

$CH_{3}CN$ 감지를 위한 최적 모물질은 $CH_{3}CN$의 억분해 온도와 생성량을 적외선 흡수 스펙트럼으로부터 비교함으로써 선정되었다. $SnO_{2}$ 표면에서 $CH_{3}CN$은 $130^{\circ}C$에서부터 열분해되기 시작하여 $300^{\circ}C$에서는 많은 양의 생성물을 생성하였다. 산화반응에 의한 $CH_{3}CN$은 $CO_{2}$, $NH_{3}$ 및 $H_{2}O$로 열분해되었으며, $320^{\circ}C$에서부터 $N_{2}O$가 생성되기 시작하였다. $SnO_{2}$ 감지소자의 $CH_{3}CN$에 대한 감지특성은 $CH_{3}CN$과 금속산화물과의 산화반응으로 인해 생성된 흡착종에 의해 영향을 받았다. 감지물질표면과의 반응에서 생성된 흡착종은 CO, $NH_{3}$, $H_{2}O$ 및 $NO_{x}$ 등이었다. $NO_{x}$의 생성량은 감지특성에 큰 영향을 나타냄을 알 수 있다. 170 ppm의 $CH_{3}CN$에 대한 $SnO_{2}$의 감도와 동작온도는 각각 70% 정도와 $300^{\circ}C$이었다. 0.2wt% Pd 첨가된 $SnO_{2}/Al_{2}O_{3}/Pd$ 감지소자는 $CH_{3}CN$에 대해 높은 감도를 나타내었으며, 응답시간은 약 10초이었다.

• Bulletin of the Korean Chemical Society
• /
• 제26권12호
• /
• pp.2017-2020
• /
• 2005

The supported bimetallic Co-containing catalysts promoted by the different amount of noble metal (Pd) have been studied in the dry reforming of methane. The activity, selectivity, stability and resistance to the carbon deposition of Co-Pd/$Al_2O_3$ catalysts depend on both the catalyst composition and process conditions. It has been observed that the Co-Pd/$Al_2O_3$ catalysts produce the various oxygenates from $CO_2$ + $CH_4$ at moderate pressures.