• Journal of the Korean Ceramic Society
• /
• v.31 no.12
• /
• pp.1588-1598
• /
• 1994

The SiC/MoSi2 composite materials were fabricated by infiltrating the mixture of molybdenum disilicide and metal silicon(MoSi2+Si=100) to a porous compact of silicon carbide and graphite under the vacuum atmosphere of 10-1 torr. The specimen were oxidized in dry air under 1 atm at 130$0^{\circ}C$~150$0^{\circ}C$ for 240 hours. The oxidation behavior was evaluated by the weight gain and loss per unit area of the oxidized samples. Also, SEM and XRD analysis of the oxidized surface of the samples were carried out. With increasing the MoSi2 content and oxidation temperature, the passive oxidation was found. The trend of weight gain of all samples was followed the parabolic rate law with the formation of a protective layer of cristobalite on the surface.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.127-134
• /
• 2000

Soil nailing is in-situ ground improvement technique of reinforcing soils using passive inclusions for the purpose of slope stability. Also soil nailing, in general, was used and studied as a reinforcement technique at cut slope, but this paper presents the results of study for soil nailing application as a reinforcement technique at the banking over slided slope. In-situ pull-out tests of nails, instrumented with strain gauges, were performed to investigate the maximum pull-out load and to calculate the unit side resistance in each different layer. And the apparent average unit side resistance of this study was compared with that of other sites installed at cut slope.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.3
• /
• pp.389-395
• /
• 2006

The fluid force reduction of a square prism having fences on the corner was studied by the measuring the drag and lift acting on the prism and by the visualization experiment of the flow around the prism. The height of the fence was 10% of the square width and the range of Reynolds number considered was from $Re=0.9{\times}104$ to $Re=2.1{\times}104$. The drag of the prism was reduced about 6.8% and the amplitude of the lift was reduced by attaching two normal fences on the rear corners of the prism. In this case, the separated flow at the front corners was reattached on the upper and lower sides of the prism and the vortex streets at the wake region were appeared more slowly than that of the prototype prism.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.61-62
• /
• 2006

The suppression of fluid force acting on a square prism near plane wall was studied by attaching fences on the comers of the prism. The height of the fence was 10% of the square width and the range of Reynolds number considered was $Re=2.0{\times}10^4$. The experimental parameters were the attaching position and numbers of fences, the space ratios $G/B(G/B=0.1{\sim}1.2)$ between prism and plane wall. The average drag coefficients were increased and the average hit coefficients were decreased and increased with the space ratios foulard plane wall. The drag of the prism was reduced average 7.6% with the space ratios by attaching the normal fence at the rear and upper comer and the horizontal normal fence at the rear and lower corner on the prism.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.596-599
• /
• 1997

In this study, the flow control system with shape memory alloy in jet engine inlet was suggested to adjust the shock boundary layer interact~on for supersonic flight system. It consisted of the flap with shape memory alloy, spar with steel, and fixing device with aluminum alloy. The advantages of itself are a simple configuration, a passive air circulation by using the flap deflection due to pressure difference, and no need to be required the auxiliary devices. Finite element analysis was conducted to predict the thenno-mechanical behavlor of the flap system with shape memory alloy. The user-defined subroutine UMAT was implemented with ABAQUS to accon~modate the thermo-mechanical constitutive relation of shape memory alloy.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.133-137
• /
• 2001

Active control of flexural vibrations of smart laminated composite beams has been carried out using piezoceramic sensor/actuator and viscoelastic material. The beams with passive constrained-layer damping have been analyzed by formulating the equations of motion through the use of extended Hamilton's principle. The dynamic characteristics such as damping ratio and modal damping of the beam are calculated for various fiber orientations by means of iterative complex eigensolution method, This paper addresses a design strategy of laminated composite under flexural vibrations to design structure with maximum possible damping capacity.

• Laser Solutions
• /
• v.2 no.1
• /
• pp.16-21
• /
• 1999

The surface of Alloy 600 was alloyed using a continuous wave $CO_2$ laser beam in order to improve its corrosion resistance. Laser surface alloying (LSA) was done by melting the surface electroplated with Cr of the alloy. The Cr concentration of the alloyed surface was 28-30 at.%, which is similar to that of Alloy 690. Alloying elements in the alloyed layer was observed to be distributed very homogeneously all over the alloyed region. According to the electrochemical and modified Huey tests, the corrosion resistance, in particular the grain boundary corrosion resistance, of the LSA specimens was significantly improved, compared with that of the as-received(AR) specimen. This improved corrosion resistance of the alloyed specimen might be attributed to the high Cr content which could make possible formation of more stable and dense passive film onto its surface.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.633-636
• /
• 2003

An Ethernet passive optical network(EPON) is a point-to-multipoint optical network. EPONs leverage the low cost, high performance curve of Ethernet systems to provide reliable data, voice and video to end user at bandwidths far exceeding current access technologies. In this paper, we propose the economical and flexible structure of optical network unit(ONU) converting optical format traffic to the customer's desired format(Ethernet, VDSL, T1, IP multicast, etc.). A unique feature of EPONs is that in addition to terminating and converting the optical signal the ONU provide Layer 2-3 switching functionality, which allows internal routing of enterprise traffic at the ONU.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.02a
• /
• pp.221-222
• /
• 2007

The UV laser trimming can be useful to have an accurate performance specification of the passive waveguide devices. In order to measure the change of the refractive index of polymer overclad layer under the irradiation of uv light in a high precision Bragg grating is fabricated on the silica core of planar waveguide and the corresponding transmittance spectrum was analyzed. An effective refractive index change of $4.7x10^{-5}$ was obtained for a straight waveguide when its $60{\mu}m$-thick overclad was irradiated by UV laser pulses of its total fluence 24 $J/cm^2$.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.4
• /
• pp.141-148
• /
• 1996

Use of stone column for deep ground treatment in soft clay soils is an effective method. The stone column significantly increases load carrying capacity of the soft clay soil. A analysis method for bearing capacity of stone column in soft clay soil is developed. The capacity made by developed method are compared wity observed values from field load test and a reasonable correlation is noted.