• Journal of the Korean Vacuum Society
• /
• v.19 no.2
• /
• pp.148-154
• /
• 2010

We have fabricated $SiO_2$ oxidation thin films by TCP-CVD (transformer coupled plasma chemical vapor deposition) method for passivation layer of OLED (organic light emitting diode). The purpose of this paper is to control and estimate the deposition rate and refracive index characteristics with process parameters. They are power, gas condition, distance of source and substrate and process temperature. The results show that transmittance of thin films is over 90%, rapid deposition rate and stable reflective index from 1.4 to 1.5 at controled process conditions. They are $SiH_4$ : $O_2$ = 30 : 60 [sccm] gas condition, 70 [mm] distance of source and substrate, no-biased substrate and under 80 [$^{\circ}C$] process temperature.

• Korean Journal of Materials Research
• /
• v.3 no.2
• /
• pp.166-174
• /
• 1993

Abstract The crack resistance of PSG(Phosphosilicate Glass) and PE-SiN(Plasma Enhanced CVD S${i_2}{N_4}$)films deposited on aluminium thin films on Si substrate was analyzed in this study. PSG was deposited by AP-CVD and PE- SiN by PE-CVD. All the films underwent repeated heat cycles at 45$0^{\circ}C$for 30 min. Crack formation and development were examined between each heat cycle. The crack behavior was found to be closely related to the stresses in the films. The stress induced by the difference in thermal expansion behavior between the passivation layers and underlying aluminum film may cause the crack. Crack resistance decreases as the thickness of PSG films increases due to the high tensile stress of the films. Phosphorus in the PSG films releases tensile stress and consequently the stress of the films tends to show compressive stress. As a result, crack resistance increased as the concentratin of P in the PSG films increased. Crack resistance in the PE-SiN films also increased with compressive stress. An experimental model to predict crack generation in the PSG and PE-SiN films during heat cycle was suggested.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.33-36
• /
• 2003

Tungsten is widely used as a plug for the multi-level interconnection structures. However, due to the poor adhesive properties of tungsten (W) on $SiO_2$ layer, the Ti/TiN barrier layer is usually deposited onto $SiO_2$ for increasing adhesion ability with W film. Generally, for the W-CMP (chemical mechanical polishing) process, the passivation layer on the tungsten surface during CMP plays an important role. In this paper, the effect of oxidants controlling the polishing selectivity of W/Ti/TiN layer were investigated. The alumina $(Al_2O_3)$ abrasive containing slurry with 5 % $H_2O_2$ as the oxidizer, was studied. As our preliminary experimental results, very low removal rates were observed for the case of no-oxidant slurry. This low removal rate is only due to the mechanical abrasive force. However, for Ti and TiN with 5 % $H_2O_2$ oxidizer, different removal rate was observed. The removal mechanism of Ti during CMP is mainly due to mechanical abrasive, whereas for TiN, it is due to the formation of metastable soluble peroxide complex.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.85-85
• /
• 2007

최근 귀금속중의 하나인 Ruthenium(Ru)은 높은 일함수, 누설전류에 대한 높은 저항성등의 톡성으로 인해 캐패시터의 하부전극으로 각광받고 있다. 하부전극으로 증착된 Ru은 일반적으로 각 캐패시터의 분리와 평탄화를 위해 건식식각이 이루어진다. 하지만, 건식식각 공정중 유독한 $RUO_4$ 가스가 발생할 수 있으며, 불균일한 캐패시터 표면을 유발할 수 있다. 이러한 문제점들을 해결하기 위해 CMP 공정이 필요하게 되었다. 하지만, Ru은 화학적으로 매우 안정하기 때문에 Ru CMP 슬러리에 대한 연구가 필요하게 되었으며, 이에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 Ru CMP 공정에서 Chemical A가 에칭제 및 산화제로 사용된 슬러리의 pH 변화와 pH 적정제에 따른 영향을 살펴보았다. Ru wafer를 이용하여 static etch rate, passivation film thickness와 wettability를 pH와 pH 적정제에 따라 비교해 보았다. 또한, pH 적정제로 $NH_4OH$와 TMAH를 이용하여 pH별 슬러리를 제작하고 CMP 공정을 실시하여 Ru의 removal rate을 측정하였다. $NH_4OH$와 TMAH의 경우 각각 130. 100 nm/min의 연마율이 측정된 pH 6에서 가장 높은 연마률을 보였으며, TMAH의 경우가 pH 전 구간에서 $NH_4OH$에 비해 낮은 연마율이 측정되었다. TEOS 에 대한 Ru의 선택비를 측정해 본 결과, $NH_4OH$의 경우 pH 8~9. TMAH의 경우 pH 6~7에서 높은 selectivity를 얻을 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.245-245
• /
• 2010

최근에 반도체 소자 및 마이크로머신, 바이오센서 등에 사용되는 미세 부품에 대한 연구 개발이 활발히 진행되고 있다. 미세 부품을 제작하기 위한 MEMS 공정은 대표적으로 화학용액을 이용한 습식식각, 플라즈마를 이용한 건식식각 등이 주를 이룬다. Micro blaster는 경도가 강하고 화학적 내성을 가지며 용융점이 높아 반도체 MEMS 공정에 어려움이 있는 기판을 다양한 형태로 식각 할 수 있는 기계적인 식각 공정 기술이라 할 수 있다. Micro blaster의 식각 공정은 고속의 날카로운 입자가 공작물을 타격할 때 입자의 아래에는 고압축응력이 발생하게 되고, 이 고압축 응력에 의하여 소성변형과 탄성변형이 발생된다. 이러한 변형이 발전되어 재료의 파괴 초기값보다 크게 되면 크랙이 발생되고, 점점 더 발전하게 되면 재료의 제거가 일어나는 단계로 이루어진다. 본 연구에서는 micro blaster 장비를 반도체 MEMS 공정에 적용하기 위한 식각 특성에 관하여 확인하였다. Micro blaster 장비와 식각에 사용한 파우더는 COMCO INC. 제품을 사용하였다. Micro blaster를 $Al_2O_3$ 파우더의 입자 크기, 분사 압력, 기판의 종류, 노즐과 기판과의 간격, 반복 횟수, 노즐 이동 속도 등의 공정 조건에 따른 식각 특성에 관하여 분석하였다. 특히 실제 반도체 MEMS 공정에 적용 가능한지 여부를 확인하기 위하여 바이오 PCR-chip을 제작하였다. 먼저 glass 기판과 Si wafer 기판에서의 식각률을 비교 분석하였고, 이 식각률을 바탕으로 바이오 PCR-chip에 사용하게 될 미세 홀과 미세 채널, 그리고 미세 챔버를 형성 하였다. 패턴을 형성하기 위하여 TOK Ordyl 사의 DFR(dry film photoresist:BF-410)을 passivation 막으로 사용하였다. Micro blaster에 사용되는 파우더의 직경이 수${\mu}m$ 이상이기 때문에 $10\;{\mu}m$ 이하의 미세 채널과 미세홀을 형성하기 어려웠지만 현재 반도체 MEMS 공정 기술로 제작 연구되어지고 있는 바이오 PCR-chip을 직접 제작하여 micro blaster를 이용한 반도체 MEMS 공정 기술에 적용 가능함을 확인하였다.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.3
• /
• pp.41-45
• /
• 2018

Two-dimensional (2D) materials have been studied extensively due to their excellent physical, chemical, and electrical properties. Among them, we report the material and device characteristics of tin disulfide ($SnS_2$). To apply $SnS_2$ as a channel layer in a transistor, $SnS_2$ channels were formed by a stripping method and a transfer method. The limitation of this method is that it is difficult to produce uniform device characteristics over a large area. Therefore, we directly deposited $SnS_2$ by atomic layer deposition (ALD) and then performed lithography. This method was able to produce devices with repeatable characteristics over a large area. However, the $SnS_2$ film was damaged by the acetone used as a photoresist (PR) developer during the lithography process, with the electrical properties of mobility of $2.6{\times}10^{-4}cm^2/Vs$, S.S. of 58.1 V/decade, and on/off current ratio of $1.8{\times}10^2$. These results are not suitable for advanced electronic devices. In this study, we analyzed the effect of acetone on $SnS_2$ and studied the device process to prevent such damage. Using polyvinyl alcohol (PVA) as a passivation layer during the lithography process, the electrical characteristics of the $SnS_2$ transistor had $2.11{\times}10^{-3}cm^2/Vs$ of mobility, 11.3 V/decade of S.S, and $2.5{\times}10^3$ of the on/off current ratio, which were 10x improvements to the $SnS_2$ transistor fabricated by the conventional method.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.2
• /
• pp.213-226
• /
• 2022

In the present study, the corrosion behavior of aluminum Al-7075 tempered (T-6 condition) alloy was evaluated by immersion testing and electrochemical testing in 1.75% and 3.5% NaCl environment at acidic, neutral and basic pH. The data obtained by both immersion tests and electrochemical corrosion tests (potentiodynamic polarization and electrochemical impedance spectroscopy tests) present that the corrosion rate of the alloy specimens is minimum for the pH=7 condition of the solution due to the formation of dense and well adherent thin protective oxide layer. Whereas the solutions with acidic and alkaline pH cause shift in the corrosion behavior of aluminum alloy to more active domains aggravated by the constant flux of acidic and alkaline ions (Cl^- and OH^-) in the media which anodically dissolve the Al matrix in comparison to precipitated intermetallic phases (cathodic in nature) formed due to T6 treatment. Consequently, the pitting behavior of the alloy, as observed by cyclic polarization tests, shifts to more active regions when pH of the solutions changes from neutral to alkaline environment due to localized dissolution of the matrix in alkaline environment that ingress by diffusion through the pores in the oxide film. Microscopic analysis also strengthens the results obtained by immersion corrosion testing and electrochemical corrosion testing as the study examines the corrosion behavior of this alloy under a systematic evaluation in marine environment.

• Analytical Science and Technology
• /
• v.19 no.5
• /
• pp.394-399
• /
• 2006

The polishing performance and the relationships of electrochemistry depending upon oxidizers and additives in the tungsten CMP slurry used in semiconductor industry were investigated. Hydrogen peroxide, ferric nitrate and potassium iodate were used as oxidizers and they showed different oxidation reactions on tungsten film depending on the kind of oxidizers and pH of slurry. The differences influenced the polishing performance. Etching reaction was predominated in the hydrogen peroxide. However, passivation reaction was prevailed in ferric nitrate and potassium iodate. TMAH and KOH raised the potential energy and removal rate of tungsten, and improved a dispersion characteristic of slurry by increasing absolute value of zeta potential. Addition of 100 ppm of poly(acrylic acid) of M.W. 250,000 improved dispersion ability.

• Journal of the Microelectronics and Packaging Society
• /
• v.31 no.3
• /
• pp.87-90
• /
• 2024

Currently, when oxides are used as insulators in hybrid bonding for 3D integration, they are prone to delamination due to their surface characteristics, and the RC delay value due to the resistance of the metal and the capacitance of the insulator increases as the wiring of the semiconductor chip becomes longer. To solve these problems, we studied the optimization of the conditions of the polymer insulator bonding method for hybrid bonding. To check the possibility of the de-wetting method, we coated a polymer film on the existing micro pillar and conducted hot-press bonding to remove the polymer between the metals. Through this study, it is expected that the introduction of polymers as insulators in hybrid bonding and fine-pitch metal bonding will improve signal transmission speed by reducing RC delay. It is also expected to be commercialized in the future to increase the number of I/O terminals by applying it to hybrid bonding.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.619-625
• /
• 2008

The effects of thermal cycling on residual stresses in both inorganic passivation/insulating layer that is deposited by plasma enhanced chemical vapor deposition (PECVD) and organic thin film that is used as a bonding adhesive are evaluated by 4 point bending method and wafer curvature method. $SiO_2/SiN_x$ and BCB (Benzocyclobutene) are used as inorganic and organic layers, respectively. A model about the effect of thermal cycling on residual stress and bond strength (Strain energy release rate), $G_c$, at the interface between inorganic thin film and organic adhesive is developed. In thermal cycling experiments conducted between $25^{\circ}C$ and either $350^{\circ}C$ or $400^{\circ}C$, $G_c$ at the interface between BCB and PECVD $ SiN_x $ decreases after the first cycle. This trend in $G_c$ agreed well with the prediction based on our model that the increase in residual tensile stress within the $SiN_x$ layer after thermal cycling leads to the decrease in $G_c$. This result is compared with that obtained for the interface between BCB and PECVD $SiO_2$, where the relaxation in residual compressive stress within the $SiO_2$ induces an increase in $G_c$. These opposite trends in $G_cs$ of the structures including either PECVD $ SiN_x $ or PECVD $SiO_2$ are caused by reactions in the hydrogen-bonded chemical structure of the PECVD layers, followed by desorption of water.