• Journal of the Korean Wood Science and Technology
• /
• 제27권4호
• /
• pp.57-64
• /
• 1999

This research was carried out to investigate the effects of density, resin and particle types on the physical and mechanical properties of the composites made from various wood particles mixed with coating paper. The experiment was designed to apply with three particles (flake, chip, and fiber) and three resin types (urea, phenol and PMDI resin). The mixed ratio of coating paper to wood particle was fixed on 50 to 50% in each board making. And also it was designed to apply for four density levels (0.6, 0.7, 0.8 and 0.9 g/$cm^3$) and four mixed formulations of coating paper to wood particle (10:90, 20:80, 30:70, and 40:60 %) to analyze clearly the effects of PMDI resin. Coating paper-wood particle composites have acceptable bending strength (MOR, MOE) though the mixed ratio of coating paper was increased, but have low internal bond strength and poor dimensional stability (WA, TS, LE). Composites with high density had higher mechanical properties but showed lower physical properties than composites with low density. In conclusion, at least up to 20% mixed ratios, coating paper-wood particle composites have acceptable physical and mechanical properties, and PMDI resin has possibility for coating paper-wood particle composite manufacture.

• 공업화학
• /
• 제10권7호
• /
• pp.1061-1065
• /
• 1999

Calorizing 처리에서 코팅분말의 입자크기 및 코팅온도가 금속표면에 형성된 코팅층의 두께에 미치는 영향을 XRD, SEM, 및 EDXS를 사용하여 고찰하였다. 코팅분말은 입자크기별로 3단계로 분리하였으며 코팅온도는 $950^{\circ}C$와 $980^{\circ}C$로 변화하였다. Calorizing 처리는 공기 및 아르곤 분위기에서 5시간 동안 행하였다. XRD 결과 공기분위기의 calorizing 처리과정에서 금속산화물($Al_2O_3$)과 질화물(AlN)이 형성됨을 관찰하였다. 공기 및 아르곤 분위기의 calorizing 처리 결과 코팅분말의 입자크기가 감소하고 코팅온도가 증가할수록 코팅층의 두께와 코팅층에서의 알루미늄의 함량이 증가함을 알 수 있었다.

• Corrosion Science and Technology
• /
• 제14권2호
• /
• pp.76-84
• /
• 2015

The components in ultra super critical (USC) steam turbine, which is under development for high efficient power generation, are encountering harsher solid particle erosion by iron oxide scales than ones in the existing steam turbines. Therefore, the currently used boride coating will not be able to hold effective protection from particle erosion in USC system and should be replaced by new particle erosion resistant coatings. One of the best protective coatings developed for USC steam turbine parts was found to be vanadium-boride (V-boride) coating which has a hardness of about 3000 HV, much higher than that of boride, 1600~2000 HV. In order to evaluate particle erosion resistance of the various coatings such as V-boride, boride and Cr-carbide coatings at high temperature, particle erosion test equipments were designed and manufactured. In addition, erosion particle velocity was simulated using FLUENT software based on semi-implicity method for pressure linked equations revised (SIMPLER). Based on experimental results of this work, the vanadium-boride coating was found to be superior to others and to be a candidate coating to replace the boride coating.

• Journal of Information Processing Systems
• /
• 제1권1호
• /
• pp.36-40
• /
• 2005

TRISO (Tri-Isotropic)-coated fuel particle is widely applied due to its higher stability at high temperature and its efficient retention capability for fission products in the HTGR (high temperature gas-cooled reactor), one of the highly efficient Generation IV reactors. The typical ball-type TRISO-coated fuel particle with a diameter of about 1 mm is composed of a nuclear fuel particle as a kernel and of outer coating layers. The coating layers consist of a buffer PyC, inner PyC, SiC, and outer PyC layer. In this study, a digital image processing algorithm is proposed to automatically measure the thickness of the coating layers. An FBP (filtered backprojection) algorithm was applied to reconstruct the CT image using virtual X-ray radiographic images for a simulated TRISO-coated fuel particle. The automatic measurement algorithm was developed to measure the coating thickness for the reconstructed image with noises. The boundary lines were automatically detected, then the coating thickness was circularly by the algorithm. The simulation result showed that the measurement error rate was less than 1.4%.

• 한국표면공학회지
• /
• 제35권3호
• /
• pp.165-171
• /
• 2002

TiN coating were deposited onto different WC-Co substrates using arc ion plating (AIP) technique. The structure and morphology for the deposited coating were characterized by x-ray diffraction (XRD) and scanning electron microscopy (SEM). The adhesion behavior of the deposited TiN coating was investigated with a conventional scratch test. Effects of WC particle size and Co content on the adhesion strength between the deposited TiN coating and substrate were studied. During the scratch test, the value of critical load was dependent of WC particle size and Co content on substrate. As the WC particle size and Co content on substrate decreased, the critical load increased. The highest critical load, approximately 110N, was obtained at WC particle size of 1$\mu\textrm{m}$ and Co content of 10wt.%.

• 한국산학기술학회논문지
• /
• 제1권1호
• /
• pp.49-54
• /
• 2000

Calorizing(또는 Aluminizing)에서 코팅분말의 입자크기 및 코팅온도가 금속표면에 형성된 코팅 층의 특성에 미치는 영향을 SEM과 EDXS를 사용하여 자세히 고찰하였다. 코팅분말은 입자크기별로 3단계로 분리하여 사용하였으며 코팅온도는 950℃ 와 980℃로 변화하였다. Calorizing 처리는 팩 세멘테이션 방법을 사용하여 아르곤 분위기에서 5시간 동안 행하였다. Calorizing 처리 결과 코팅분말의 입자크기가 감소하고 코팅온도가 증가할수록 코팅 층의 두께와 코팅 층에서의 알루미늄의 함량이 증가하였다. 또한 오팅분말의 크기가 작은 경우(150-200 mesh) 코팅 층 표면에 형성된 기공이 현저히 감소하였고 표면의 균일성도 우수함을 알 수 있었다.

• Journal of Welding and Joining
• /
• 제25권4호
• /
• pp.42-48
• /
• 2007

An inert gas atomized NiTiZrSiSn bulk metallic glass feedstock was sprayed onto the copper plate using vacuum plasma spraying process. In order to change the in-flight particle energy, that is, thermal energy, the hydrogen gas flow rate in plasma gas mixture was increased at the constant flow rate of argon gas. Coating and single pass spraying bead were produced with the least feeding rate. Regardless of the plasma gas composition, fully melted through unmelted particle could be observed on the overlay coating. However, the frequency of the unmelted particle number density was increased with the decrease of the hydrogen gas flow rate. The amorphous phase fraction within coating was also affected by the number density of the unmelted particle.

• 한국분말재료학회지
• /
• 제19권5호
• /
• pp.348-355
• /
• 2012

Cold spray deposition using Titanium powder was carried out to investigate the effects of powder morphology and powder preheating on the coating properties such as porosity and hardness. The in-flight particle velocity of Ti powder in cold spray process was directly measured using the PIV (particle image velocimetry) equipment. Two types of powders (spherical and irregular ones) were used to manufacture cold sprayed coating layer. The results showed that the irregular morphology particle appeared higher in-flight particle velocity than that of the spherical one under the same process condition. The coating layer using irregular morphology powder represented lower porosity level and higher hardness. Two different preheating conditions (no preheating and preheating at $500^{\circ}C$) were used in the process of cold spraying. The porosity decreased and the hardness increased by conducting preheating at $500^{\circ}C$. It was found that the coating properties using different preheating conditions were dependent not on the particle velocity but on the deformation temperature of particle. The deposition mechanism of particles in cold spray process was also discussed based on the experimental results of in flight-particle velocity.

• 펄프종이기술
• /
• 제39권4호
• /
• pp.29-37
• /
• 2007

The effects of latex particle size, basis weight of base paper and coating color concentration on the printing quality of coated paper were investigated. Coating colors were prepared with five types of latexes having different particle sizes. Coated papers were produced with high solid coating colors and with low solid coating colors in a industrial coater, respectively. In high solid coating colors, rheology modifier was used and GCC content was high. It was concluded that, in order to control binder migration and hence print mottle, latex particle sizes shall be controlled as well as formation, sizing degree and roughness of basis paper.

• 펄프종이기술
• /
• 제33권1호
• /
• pp.53-61
• /
• 2001

This study was carried out to evaluate the effect of coating pigments on the printability by investigating the pore structure of casting layer such as the number, size and distribution of pores and the pore rate. The coating structure was mainly determined by the interaction between pigment and binder. It means that the structure of pores was chiefly affected by the shape and size distribution of pigments and their packing rate. The physical properties of pore have close relationships with ink set-off, the speed of ink penetration and printing gloss. The results suggested that the rate and number of pores were greatly affected by the particle size distribution and shape of pigments. The rate of pore increased with the reduction of particle size distribution of pigments. Calcite was effective to improve greatly the printability of coated paper.