• 터널과지하공간
• /
• 제23권1호
• /
• pp.54-65
• /
• 2013

선형절삭시험(Linear Cutting Machine)은 TBM(Tunnel Boring Machine)에서의 디스크 커터 설계와 굴진성능 예측을 위한 가장 신뢰성 있는 시험 중의 하나로서, 실대형 암석시료를 대상으로 실제의 커터 하중을 예측할 수 있는 장점을 갖고 있지만, 시료의 채취 및 운반이 용이하지 않고, 1회 시험에 많은 비용이 소요되는 단점을 갖고 있다. 최근 선형절삭시험이 갖는 이러한 경제적 시간적 제약점들을 극복할 수 있는 현실성 있는 수치모델의 개발에 관한 연구가 활발히 진행되고 있다. 본 연구에서는 3차원 입자결합모델을 이용하여 디스크 커터의 절삭에 의한 부산 응회암의 파쇄양상과 최적 커터간격을 도출하였다. 본 해석에서 분석된 비에너지는 $14.3MJ/m^3$ 일 때 최소값을 나타냈다. 이때의 최적의 s/p 비는 약 16 으로 분석되었으며, 부산응회암의 선형절삭시험 및 유한요소법에 의한 수치해석 연구결과와 유사한 경향을 나타냈다.

• Smart Structures and Systems
• /
• 제30권1호
• /
• pp.49-62
• /
• 2022

Experimental and discrete element methods were used to investigate the effects of triple joints lengths and triple joint angle on the failure behavior of rock mass under uniaxial compressive test. Concrete samples with dimension of 20 cm × 20 cm × 5 cm were prepared. Within the specimen, three imbedded joint were provided. The joint lengths were 2 cm, 4cm and 6 cm. In constant joint lengths, the angle between middle joint and other joints were 30°, 60°, 90°, 120° and 150°. Totally 15 different models were tested under compression test. The axial load rate on the model was 0.05 mm/min. Concurrent with experimental tests, the models containing triple joints, length and joint angle are similar to the experiments, were numerical by Particle flow code in two dimensions (PFC2D). Loading rate in numerical modelling was 0.05 mm/min. Tensile strength of material was 1 MPa. The results show that the failure behaviors of rock samples containing triple joints were governed by both of the angle and the length of the triple joints. The uniaxial compressive strengths (UCS) of the specimens were related to the fracture pattern and failure mechanism of the discontinuities. Furthermore, it was shown that the compressive behavior of discontinuities is related to the number of the induced tensile cracks which are increased by decreasing the joint length. Along with the damage failure of the samples, the acoustic emission (AE) activities are excited. There were only a few AE hits in the initial stage of loading, then AE hits rapidly grow before the applied stress reached its peak. In addition, every stress drop was accompanied by a large number of AE hits. Finally, the failure pattern and failure strength are similar in both methods i.e., the experimental testing and the numerical simulation methods.

• Structural Engineering and Mechanics
• /
• 제84권5호
• /
• pp.633-649
• /
• 2022

In this study, the effect of circle tunnel on the force distribution around underground rectangular gallery was investigated using theoretical approach, experimental test and Particle flow code simulation (PFC). Gypsum model with dimension of 1500×1500 mm was built. Tensile strength of material was 1 MPa. Dimension of central gallery was 100 mm×200 mm and diameter of adjacent tunnel in its right side was 20 mm, 40 mm and 60 mm. Horizontal distance between tunnel wall and gallery edge were 25, 50, 75, 100 and 125 mm. using beam theory, the effect of tunnel diameter and distance between tunnel and gallery on the induced force around gallery was analyzed. In the laboratory test, the rate of loading displacement was set to 0.05 millimeter per minute. Also sensitivity analysis has been done. Using PFC2D, interaction between tunnel and gallery was simulated and its results were compared with experimental and theoretical analysis. The results show that the tensile force concentration has maximum value in center of the rectangular space. The tensile force concentration at the right side of the axisymmetric line of gallery has more than its value in the left side of the galleries axisymmetric line. The tensile force concentration was decreased by increasing the distance between tunnel and rectangular space. In whole of the configurations, the angles of micro cracks fluctuated between 75 and 105 degrees, which mean that the variations of tunnel situation have not any influence on the fracture angle.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권5호
• /
• pp.818-826
• /
• 2004

The spray-induced mixing characteristics and thermal decomposition of aqueous urea solution into ammonia have been studied to design optimum sizes and geometries of the mixing chamber in SCR(Selective Catalytic Reduction) system. The cold flow tests about the urea-injection nozzle were performed to clarify the parameters of spray mixing characteristics such as mean diameter and velocity of drops and spray width determined from the interactions between incoming air and injected drops. Discrete particle model in Fluent code was adopted to simulate spray-induced mixing process and the experimental results on the spray characteristics were used as input data of numerical calculations. The simulation results on the spray-induced mixing were verified by comparing the spray width extracted from the digital images with the simulated Particle tracks of injected drops. The single kinetic model was adopted to predict thermal decomposition of urea solution into ammonia and solved simultaneously along with the verified spray model. The hot air generator was designed to match the flow rate and temperature of the exhaust gas of the real engines The measured ammonia productions in the hot air generator were compared with the numerical predictions and the comparison results showed good agreements. Finally, we concluded that the design capabilities for sizing optimum mixing chamber were established.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권3호
• /
• pp.595-609
• /
• 2015

The wake characteristics of Contra-Rotating Propeller (CRP) were investigated using numerical simulation and flow measurement. The numerical simulation was carried out with a commercial CFD code based on a Reynolds Averaged Navier-Stokes (RANS) equations solver, and the flow measurement was performed with Stereoscopic Particle Image Velocimetry (SPIV) system. The simulation results were validated through the comparison with the experiment results measured around the leading edge of rudder to investigate the effect of propeller operation under the conditions without propeller, with forward propeller alone, and with both forward and aft propellers. The evolution of CRP wake was analyzed through velocity and vorticity contours on three transverse planes and one longitudinal plane based on CFD results. The trajectories of propeller tip vortex core in the cases with and without aft propeller were also compared, and larger wake contraction with CRP was confirmed.

• 터널과지하공간
• /
• 제23권6호
• /
• pp.493-505
• /
• 2013

본 수치해석논문에서는 절리와 단층대를 포함한 지열저류층에 수리자극을 가할 시 수반되는 유도지진과 단층대의 변형을 개별요소법을 사용하여 모델링하였다. 수채해석기법은 2차원 입자유동코드를 기반으로 하며 수리역학적 상호작용기법과 미소파괴음의 모멘트텐서 역산알고리즘이 결합되었다. 수치해석의 주요결과로는 시공간적으로 변하는 유도지진의 분포와 규모 그리고 단층대의 변형(파괴 및 전단변위)과 주입유체압력의 시공간적 분포와의 상관관계이다. 첫 번째 수치해석으로부터 절리가 분포하는 지열저류층에서의 수리자극에 의한 유도지진의 분포는 주입유체의 점성에 상당한 영향을 받는 것으로 나타났다. 주입유체의 점성이 낮은 경우 (1 cP), 유도지진의 발생범위가 큰 것으로 나타났으며, 주입 후 발생하는 유도지진의 개수와 규모 또한 높게 나타났다. 단층대가 존재하는 지열저류층의 수리자극 모델링의 결과, 주입정의 위치가 단층대와 가까운 경우 작은 주입수 압력분포(<0.1 MPa)로도 단층대의 파괴와 전단변형을 일으킬 수 있는 것으로 나타났다. 본 논문에서 소개한 수치해석기법은 수리자극을 통한 지열저류층 개발 시 유도지진의 분포와 규모를 실제 유체주입작업전에 예측할 수 있게 함으로써 지열에너지개발 분야에서 유용하게 사용될 수 있을 것으로 기대한다.

• Journal of Korean Society for Atmospheric Environment
• /
• 제16권E호
• /
• pp.47-57
• /
• 2000

This study focuses on the investigation of the effects of windspeed and particle size on the dust control characteristics inside a test dome built in the Port of Inchon to reduce the fugitive dust originating from the handling of animal feed stuff in the open pile area. The flow field inside the test dome and the trajectories of the particles were calculated using a commercial CFD code, FLUENT, assuming that the animal feed stuff handling activity took place inside the test dome. It was found from the simulation results that high windspeed and small particle size give rise to the increase in both the escaped fraction and the suspended fraction of the particles emitted from the animal feed stuff handing activity. Here, high escaped fraction represents the high possibility of fugitive dust problem outside the test dome, whereas high suspended fraction means the high possibility of severe dust pollution inside the test dome. Ore simulation results clearly show that the existing test dome was not designed properly to meet the proposed goal, low escaped fraction and low suspended fraction. Hence, we suggest the need of an efficient ventilation system inside the dome to control the dust.

• 터널과지하공간
• /
• 제30권4호
• /
• pp.320-334
• /
• 2020

본 수치해석연구에서는 국제공동연구프로젝트 DECOVALEX2019의 Task B의 일환으로 PFC3D를 기반으로한 수리역학연계모델을 개발하여 스위스 Mont Terri 지하연구시설에서 수행된 단층의 유체주입으로 인한 슬립시험을 모사하였다. 이를통해, 개발한 PFC3D 수리역학연계모델이 가진 한계점과 향후 보완할 점을 검토하고자 하였다. PFC3D를 기반으로한 3차원 입자결합모델 내 공극-유동통로모델을 생성하였으며 이를 사용하여 Mont Terri Step 2 단층내 유체주입실험을 모사하였다. 모델링결과 단층대를 따라 주입유체의 유동에 의한 단층대의 변형을 확인하였지만, 관측정에서의 시간에 따른 수압변화는 현장측정치와 부분적으로 일치하는 경향을 확인하였다. 현장측정 관측수압은 초기 유체주입 압력증가에 거의 변화를 보이지 않고 주입수압이 최대치에 도달할때쯤 급격한 증가를 보이는반면, 모델링에서는 주입압력이 증가함에 따라 관측수압도 부드럽게 증가하는 경향을 보였다. 이러한 부분적으로 일치하는 결과의 원인으로는 Mont Terri 현장의 단층을 모사하는 방법에 기인하는 것으로 판단하다. PFC3D에서는 단층을 손상대와 코어균열의 조합으로 모사하였고 단층대의 두께가 약 2 m로 주입유체가 단층대를 통해 유동하도록 모사하였기에 현장에서의 주입유체의 단층내 유동보다 그 유동범위가 크게 모사되었다고 판단한다. 또한, 현장단층에서와 같이 단층내부에 존재하는 충진물질로 인해 단층내 수리유동이 제한되어 국부적으로 과잉공급수압이 형성될 수 있는 기재를 모사하지 못한 점 또한 모델링 결과와 현장측정결과가 부분적으로 일치하는 원인일 수 있다. 단층변형의 경우는 모델링결과와 현장측정결과 유사한 수준으로 일치하는 결과를 확인하였다. 수치모델을 변형하여 단층대의 두께를 감소시키고 단층내 충진 물질의 비균질적인분포를 모사할 수 있는 방법론에 대한 후속 연구를 통해 PFC3D 수리역학연계모델의 유체주입으로 인한 단층활성화 연구로의 적용성을 향상시키는 것을 제안하고 한다.

• 산업기술연구
• /
• 제20권A호
• /
• pp.73-82
• /
• 2000

This study was implemented to find an optimal model for wastewater treatment processes using PHOENICS(Parabolic, hyperbolic or Elliptic Numerical Integration Code Series) and ASM(Activated Sludge Model). PHOENICS is a general software based upon the laws of physics and chemistry which govern the motion of fluids, the stresses and strains in solids, heat flow, diffusion, and chemical reaction. The wastewater flow and removal efficiency of particle in two phase system of a grit chamber in wastewater treatment plant were analyzed to inquire the predictive aspect of the operational model. ASM was developed for a biokinetic model based upon material balance in complex activated sludge systems, which can demonstrate dynamic and spatial behavior of biological treatment system. This model was applied to aeration tank and settling chamber in Choonchun city, and the modeling result shows dynamic transport in aeration tank. PHOENCS and ASM could be contributed for the optimal operation of wastewater treatment plant.

• Journal of Mechanical Science and Technology
• /
• 제17권7호
• /
• pp.1054-1062
• /
• 2003

The numerical simulations of flow and pollutant particle dispersion are described for two-dimensional bell shaped hills with various aspect ratios. The Reynolds-averaged incompressible Navier-Stokes equations with low Reynolds number $\kappa$-$\varepsilon$ turbulent model are used to simulate the flowfield. The gradient diffusion equation is used to solve the pollutant dispersion field. The code was validated by comparison of velocity, turbulent kinetic energy, Reynolds shear stress, speed-up ratio, and ground level concentration with experimental and numerical data. Good agreement has been achieved and it has been found that the pollutant dispersion pattern and ground level concentration have been strongly influenced by the hill shape and aspect ratio, as well as the location and height of the source.