• Journal of Environmental Impact Assessment
• /
• v.8 no.2
• /
• pp.31-44
• /
• 1999

Atmospheric dry deposition flux and ambient particle mass size distribution were measured to evaluate the impact of atmospheric deposition around the Nanjido landfill sites. Wind direction affects greatly on the variation of mass flux and mass size distribution and made two times higher when the wind was blown from the road side. The effect of Nanjido landfill on the mass size distribution was significant comparing to simultaneously measured mass size distribution at the other sampling site. The results showed that the particle diameter bigger than $10{\mu}m$ explained the majority of atmospheric dry deposition flux. A survey was also carried out to investigate the contamination of soils in a completed Nanjido landfill. The chemical properties of the soil analyzed in the present study include pH, oxidation-reduction potential (ORP), anion and cation concentration, total organic carbon(TOC), and some-metal elements concentrations were analyzed. Microbial activity in the soils was also evaluated by measuring dehydrogenase activities. TOC in the soil contaminated with leachate was $467.0{\mu}g/g-dry$ soil, and the TOC in the soil, where Nanjido landfill gases were emitted from, was $675{\mu}g/g-dry$ soil. The highest microbial activity of $968.0{\sim}2147{\mu}g-TPF/g-dry$ soil day was found in the soil spouting Nanjido landfill gases. Compared with those in the uncontaminated soil, the concentrations of Cr, Cu and Ph in the contaminated soil were higher.

• Particle and aerosol research
• /
• v.9 no.3
• /
• pp.149-161
• /
• 2013

Experiments on photochemical reactions of purified air alone in an indoor smog chamber were carried out after flushing Teflon bags with purified air for many hours in order to check the level of contamination on the chamber wall. Ozone concentrations were linearly increased from <4 ppb up to about 8 ppb with irradiation time for four hours. Outgassing of NOx from the chamber wall was found to be less than 1 ppb. New ultrafine particles were formed and grown up to about 70 nm during the photochemical reactions, and then total number and mass concentrations of particles were increased from <10 particles/$cm^3$ up to about 4,000 particles/$cm^3$ and $1.3{\mu}g/m^3$, respectively. The wall conditions of these Teflon bags flushed with purified air might not severly affect the chamber experimental results for photochemical reactions of polluted urban ambient air. The difference of gaseous species between two chambers was 2.4 ppb of ozone at most, indicating that the wall cleaning performance of two chambers was nearly similar.

• Particle and aerosol research
• /
• v.13 no.2
• /
• pp.65-77
• /
• 2017

In recent large-scale semiconductor manufacturing cleanrooms, the energy consumption in outdoor air conditioning (OAC) systems to heat, humidify, cool and dehumidify outdoor air(OA) represents about 40~50 % of the total cleanroom power consumption required to maintain cleanroom environment. Therefore, the assessment of energy consumption in outdoor air conditioning systems is essential for reducing the outdoor air conditioning load for a cleanroom. In the present study, an experiment with an outdoor air flow rate of $1,000m^3/h$ was conducted to compare the energy consumption in steam humidification, simple air washer, exhaust air heat recovery type air washer and dry cooling coil(DCC) return water heat recovery type air washer OAC systems. Besides, a numerical analysis was carried out to evaluate the annual energy consumption of the aforementioned four OAC systems. It was shown that the simple air washer, exhaust air heat recovery type air washer and DCC return water heat recovery type air washer OAC systems using water spray humidification were more energy-efficient than the steam humidification OAC system. Furthermore the DCC return water heat recovery type air washer OAC system was the most energy-efficient.

• Journal of Environmental Science International
• /
• v.15 no.12
• /
• pp.1171-1175
• /
• 2006

Deposited road particles (DRPs) were analysed for heavy metal concentrations at four different roads in a city, Korea. The samples were collected using a roadway surface vacuum cleaning vehicle which was commonly used in collecting roadway surface particles. Six particle size ranges were analyzed separately for twelve heavy metal elements (Cd, Cr, Pb, Ni, Al, As, Co, Cu, Fe, Mn, Zn and Hg). At all sampling sites, the high concentration of the heavy metals occurred in the <74um particle size range, which conventional roadway cleaning vehicles do not remove efficiently. The Pb concentration significantly increased with decreasing particle size of DRPs, and other toxic heavy metals (Cd, Cr and Ni) also showed similar results. The heavy metal concentrations in the smaller size fraction of DRPs is important because they are contaminants that are preferentially transported by road runoff during rainfall.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.8
• /
• pp.1069-1076
• /
• 2002

Contamination particles in a hard disk drive can cause serious problems including slider crash and thermal asperities. A recirculation filter is typically installed in the hard disk drive to remove the particles. Measurements and theoretical predictions of particle concentration decay with the filter are carried out for a commercially available HDD. Especially, the effect of disk rotational speed on the particle capture efficiency is investigated. Results show that filter efficiency is higher for higher disk rotational speed.

• Journal of the Korean Ceramic Society
• /
• v.35 no.10
• /
• pp.1055-1060
• /
• 1998

The effects of particle size distribution have been investigated on the high frequency low loss Mn-Zn fer-rites. The particle size distribution was controlled by milling time. Zirconia ball and engineering plastic jar were employed to avoid iron contamination from the milling media. As increasing the milling time BET value was increased from 0.55 to 3.21m2/g and mean particle size was decreased from 2.1 $\mu\textrm{m}$ to 1.0$\mu\textrm{m}$ The large specific surface area of initial powder resulted in the high density of sintered core. However starting powders with high BET lead to inhomogeneous grain growth as well as poor electromagnetic pro-perties at sintering temperature above 1300$^{\circ}C$.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.1
• /
• pp.1-7
• /
• 2013

This study was on leaching test(KSLT, TCLP) of the aggregate for the products(RA-1) and for the site(RA-2) to evaluate the characteristics of contaminants and the possibility of contamination arising from the aggregate. On the basis pH, conductivity and heavy metal contents in the aggregate, RA-1 indicated higher than RA-2. As a result of the leaching test, the pollutants were eluted from the aggregate increased as the particle size of the aggregate was smaller. The pH in the aggregate had a strong alkali by a pH value of 9.0~12.3, the conductivity was higher in less than 10mm RA-1 due to the leaching of dissolved inorganic ions. The heavy metals satisfied the leaching standards of KSLT and less 10% was eluted from the aggregate. As a result of evaluating water pollution possibility of the aggregate, the pH displayed in items with a very high possibility of contamination, conductivity and turbidity did in item with a low possibility of contamination and on the other hand the heavy metals did in item with a very low possibility of contamination.

• Journal of Environmental Health Sciences
• /
• v.32 no.1 s.88
• /
• pp.46-52
• /
• 2006

Results for the concentrations of total polychlorinated biphenyls (total PCBs) and the PCB profile with different types of leaves from four coniferous trees (pine needles) at the same sampling site are presented. Concentrations of total PCBs detected in pine needles were very similar among them regardless of their different types of leaves, which means a possibility for bio-monitoring regional contamination of PCBs. Correlation coefficients(r) of PCB congeners between pine needles were very significant (r>0.97, p<0.001), which showed that PCB congener's patterns of each pine needle were similar. Profiles of PCBs detected in pine needles showed correlation with gaseous phase PCBs in air, otherwise not with particle phase PCBs in air. Therefore, it was estimated that dry gaseous deposition was a principal pathway of PCBs accumulation in pine needles. In addition, although we analyse a different types of leaves in pine needles at the same region, they can be used to identify regional contamination patterns of PCBs for larger regions.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.120-129
• /
• 2002

New method and device for the on-line measurement of soot concentration in a diesel engine oil are proposed, where the measurement principle is based mainly on attenuated internal total reflection. Various laboratory tests of the detector were performed mainly with carbon black particles of different contamination levels. It was found that the proposed detector could be well used to monitor oil deterioration due to soot contamination. Operational range of the detector was found from 0 to 5 mass percentage of soot content. Test results with water and fuel dilution showed that these effects were not remarkable. However, adsorption of carbon black particles to a measurement surface was considered to be a critical problem in the new detector. Effects of particle deposition onto the interface was experimentally evaluated with the oil temperature and turbulence and discussed throughout this work.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.202-202
• /
• 2008

The world gross market of many kinds of electronics, such as TV and mobile phone has been increasing rapidly these days. It is mainly caused by the amazing developments of IT technology during past decade and the changes of individual life style for the better. Thanks to the increases of electronics manufactured in quantity, much more electronic components such as MLCC (multi layer ceramic capacitor) and PCB (printed circuit board), which are our main products, have been needed as a consequence. Though it was reported that total market of electronic components exceeds several hundreds of billion dollars, there are many manufactures struggling for survival in the competition of electronics components. Then the recognition of quality as a key technology has spread and the efforts for high-yield production lines have been kept in many companies. In this paper, our efforts to eliminate the contamination of particles and the diffusion of some volatile organic compounds which is very harmful to workers at production line have been introduced.