• The Journal of Engineering Geology
• /
• v.14 no.4 s.41
• /
• pp.371-379
• /
• 2004

Soil investigation data at 7 different locations around Honam costal region were analyzed and experimental correlations between soil properties and parameters of soft clay were presented. Most soils were classified as CL and CH by the Unified Soil Classification System and were unstable structurally because the water contents were generally greater than the liquid limits. The compression index has good correlations with water content, liquid limit and initial void ratio. The trend of these correlations were similar to the Skempton equation Cc = 0.009(LL -10) and other studies for Korean soft clays but the constants were small different. The slope of these correlations for Honam costal region were slightly greater than those for Kyunggi costal region and Kyungnam costal region. The correlation coefficient (R) between the liquid limit and the plastic index is 0.93. It is seen that not only the water content and the liquid limit but also the water content and the initial void ratio are correlate, therefore the experimental equations were presented for the practical purpose.

• The Journal of Engineering Geology
• /
• v.22 no.3
• /
• pp.275-281
• /
• 2012

Thermal distribution in soils must be considered in engineering designs and constructions, including estimates of frost heave and thaw settlement, infrastructure in cold regions, and geothermal systems. Because thermal conductivity is a key parameter for evaluation of thermal distribution in soils, it must be accurately estimated. The thermal conductivity of fine-grained soils has been widely studied in recent years; however, few studies have reported a reliable method for experimental measurement. The present study presents the results of an experimental investigation of the thermal conductivity of a saturated kaolinite-silica mixture with respect to the variation of dry density. Thermal conductivities were measured in Constant Rate of Strain (CRS) consolidation tests, and the experimental data were analyzed to evaluate the accuracy of the new measurement system. In addition, we present an evaluation method for predicting thermal conductivity in fine-grained soils.

• Tunnel and Underground Space
• /
• v.16 no.2 s.61
• /
• pp.166-178
• /
• 2006

Recently, the frequency of occurring dynamic events such as earthquakes, explosives blasting and other types of vibration has been increasing. Besides, the chances of exposure for rock discontinuities to free faces get higher as the scale of rock mass structures become larger. For that reason, the frictional behavior of rock joints under dynamic conditions needs to be investigated. In this study, artificially fractured rock joint specimens were prepared in order to examine the dynamic frictional behavior of rough rock joint. Roughness of each specimen was characterized by measuring surface topography using a laser profilometer and a series of shaking table tests was carried out. For mated joints, the static friction angle back-calculated ken the yield acceleration was $2.7^{\circ}$ lower than the tilt angle on average. The averaged dynamic friction angle for unmated joints was $1.8^{\circ}$ lower than the tilt angle. Displacement patterns of sliding block were classified into 4 types and proved to be related to the first order asperity of rock joint. The tilt angle and the static friction angle for mated joints seem to be correlated to micro average inclination angle which represents the second order asperity. The tilt angle and the dynamic friction angle for unmated Joints, however, have no correlation with roughness parameters. Friction angles obtained by shaking table test were lower than those by direct shear test.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.5
• /
• pp.458-463
• /
• 2010

Since the acoustic nonlinearity is sensitive to the minute variation of material properties, the nonlinear ultrasonic technique(NUT) has been considered as a promising method to evaluate the material degradation or fatigue. However, there are certain limitations to apply the conventional NUT using the bulk wave to thin plates. In case of plates, the use of Lamb wave can be considered, however, the propagation characteristics of Lamb wave are completely different with the bulk wave, and thus the separate study for the nonlinearity of Lamb wave is required. For this work, this paper analyzed first the conditions of mode pair suitable for the practical application as well as for the cumulative propagation of quadratic harmonic frequency and summarized the result in for conditions; (1) phase matching, (2) non-zero power flux, (3) group velocity matching, and (4) non-zero out-of-plane displacement. Experimental results in aluminum plates showed that the amplitude of the secondary Lamb wave and nonlinear parameter growed up with increasing propagation distance at the mode pair satisfying the above all conditions and that the ration of nonlinear parameters measured in Al6061-T6 and Al1100-H15 was closed to the ratio of the absolute nonlinear parameters.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.3 no.3
• /
• pp.142-148
• /
• 1998

Environmental baseline information is necessary in order to assess the potential environmental impact of future manganese-nodule mining on the deep-seabed ecosystem. Total ATP (T-ATP), dissolved ATP (D-ATP) and particulate ATP (P-ATP) were measured to estimate total microbial biomass and to elucidate their vertical distribution patterns in the seabed of KODOS (Korea Deep Ocean Study) area, northeast equatorial Pacific Ocean. Within the upper 6 cm depth of sediment, the concentrations of T-ATP, D-ATP and P-ATP ranged from 4.4 to 40.6, from 0.6 to 16.1, and from 3.0 to 29.2 ng/g dry sediment, respectively. Approximately 84% of T-ATP, 81% of D-ATP, and 74% of P-ATP were present within the topmost 2 cm depth of sediment, and the distributions of ATP were well correlated with water content in the sediment. These results indicate that the distribution of total microbial biomass was largely determined by the supply of organic matter from surface water column. Fine-scale vertical variations of ATP were detected within 1-cm thick veneer of the sediment samples collected by multiple corer, while no apparent vertical changes were observed in the box-cored samples. It is evident that the box-core samples were disturbed extensively during sampling, which suggests that the multiple corer is a more appropriate sampling gear for measuring fine-scale vertical distribution pattern of ATP within thin sediment veneer. Overall results suggest that the concentrations of ATP, given their clear changes in vertical distribution pattern within 6 cm depth of sediment, are a suitable environmental baseline parameter in evaluating the variations of benthic microbial biomass that are likely to be caused by deep-seabed mining operation.

• Journal of Trauma and Injury
• /
• v.19 no.1
• /
• pp.67-73
• /
• 2006

Purpose: The arterial base deficit (BD) has proven to be useful in the evaluation and management of trauma patients. Indicators such as the Triage-Revised Trauma Score (t-RTS) and the systemic inflammatory response syndrome (SIRS) score have been used as triage tools for emergency trauma patients in Korea. The purpose of this study was to assess the usefulness of the initial BD in predicting injury severity and outcome in the trauma population. Methods: The medical records of 308 consecutive trauma patients admitted to the Emergency Center of Masan Samsung Hospital from January 2004 to December 2004 were carefully examined prospectively and retrospectively, and 291 patients were selected as subjects for this research. The SIRS score and the t-RTS were calculated based on the records from the emergency department, and the BD was calculated based on the arterial blood gas analysis obtained within 30 minutes of admission. The efficiency of the three indicators as triage tools was evaluated by using cross tabulations in two - by - two matrices and by using a receiver operating characteristic (ROC) curve analysis. Results: When the mortality was used as the outcome parameter, the sensitivity and the accuracy of the initial BD were higher than those of the SIRS score (p<0.05) and were same as those of the t-RTS. The areas under the ROC curves of the initial BD, the SIRS score, and the t-RTS were $0.740{\pm}0.087$, $0.696{\pm}0.082$, and $0.871{\pm}0.072$, respectively (95% confidence interval). When emergency operation and blood transfusion requirements were used as outcome parameters, the comparisons of the sensitivities and the accuracies of the initial BD and the other two indicators showed the same pattern as mentioned above. The areas under the ROC curves of the initial BD were 0.7~0.8 and were larger than those of the SIRS score (p<0.05). Conclusion: The ability of the initial BD to predict injury severity and outcome was similar to those of the t-RTS and the SIRS score. Therefore, the authors suggest that the initial BD may be used as an alternative to previous triage tools for trauma patients.

• Journal of the Korean Society of Tobacco Science
• /
• v.21 no.2
• /
• pp.109-118
• /
• 1999

A model predicted describing the effect of cigarette making materials on the level of filter ventilation was developed and evaluated. The developed model was expressed in terms of a linear and quadratic relationship which was validated with experimental measurements for different porosity of plug wrap and tipping paper, unencapsulated pressure drop of filter plug and cigarette column and vent position. Forty-six experimental frequencies were determined as a result of using three levels with five factors Box-Behnken design and analyzed by the multiple regression analysis with backward stepwise in STATISTICA/PC under restricted conditions. The four factors, except filter pressure drop variable, were statistically significant at the level of 0.05 but most of all linear by linear interactions were comparatively lower significant. By the analysis of linear and quadratic regression coefficient, filter ventilation of the cigarette was affected by porosity of plugwrap (5.87, -4.25), porosity of tip paper (5.68, -1.00), vent position (-3.87, 3.08), tobacco column pressure drop (2.56, 0.66), and filter pressure drop (1.50, 0.58) in the decreasing order. It should be emphasized that the major conclusion of this study was not that any particular parameter was linear or quadratic on any limit scale, but that there were highly significant relationships among factors involving linear, quadratic and their interaction and perhaps even linearity between and within factors. While, there is also quite strong evidence that vent position from mouth end and cigarette making materials are reverse relationship on this experimental model. On the basis of the result, it can be concluded that the porosity of the plug wrap and tipping paper has a marked effect on degree of filter ventilation rate. The F-value of plug wrap and tipping paper porosity among five factors were 39.2 and 36.8 respectively with P-value of 0.000 indicating higher significant for both factors. According to the analysis of variance, the model fitted for filter ventilation was significant at 5% confidence level and the coefficient of determination ($R^2$=0.84) was the proportion to variability in the data well fitted for by the model.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.4
• /
• pp.325-334
• /
• 2010

In this study, an unbraced five-story steel-framed structure was designed in accordance with KBC2005 to understand the features of structural behavior for the arrangement of semi-rigid connections. A pushover analysis of the structural models was performed, wherein all the connections were idealized as fully rigid and semi-rigid. Additionally, horizontal and vertical arrangements of the semi-rigid connection were adopted for the models. A fiber model was utilized for the moment-curvature relationship of the steel beam and the column, and a three-parameter power model was adopted for the moment-rotation angle of the semi-rigid connection. The top displacement, base-shear force, required ductility for the connection, sequence of the plastic hinge, and design factors such as the overstrength factor, ductility factor, and response modification coefficient were investigated using the pushover analysis of a 2D structure subjected to the equivalent static lateral force of KBC2005. The partial arrangement of the semi-rigid connection was found to have secured higher strength and lateral stiffness than that of the A-Semi frame, and greater ductility than the A-Rigid frame. The TSD connection was found suitable for use for economy and safety in the sample structure.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.2
• /
• pp.129-137
• /
• 2010

In this study, a five-story steel frame was designed in accordance with KBC2005 to evaluate the effect of the beam-column connection on the structural behavior. The connections were designed as a fully rigid connection and as a semirigid connection. A fiber model was utilized to describe the moment-curvature relationship of the steel beam and column, and a three-parameter power model was adopted for the moment-rotation angle of the semirigid connection. To evaluate the effects of higher modes on structural behavior, the structure was subjected to a KBC2005-equivalent lateral load and lateral loads considering higher modes. The structure was idealized as a separate 2D frame and as a connected 2D frame. The pushover analysis of 2D frames for the lateral load yielded the top displacement-base shear force, design coefficients such as overstrength factor, ductility ratio, and response modification coefficient, demanded ductility ratio for the semirigid connection,and distribution of plastic hinges. The sample structure showed a greater response modification coefficient than KBC2005, the higher modes were found to have few effects on the coefficient, and the lateral load of KBC2005 was found to be conservative. The TSD connection was estimated to secure economy and safety in the sample structure.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.5
• /
• pp.33-36
• /
• 2007

In recent years the convective-dispersive equation has been often discredited in predicting subsurface solute transport under field conditions due to presence of preferential flow paths. Kim et al. (2005) proposed a simple equation that can predict the breakthrough of solutes without excessive data requirements. In their Generalized Preferential Flow Model (GPFM), the soil is conceptually divided in a saturated "distribution layer" near the surface and a "conveyance zone" with preferential flow paths below. In this study, we test the model with previously published data, and compare it with a classical convective-dispersive model (CDM). With three parameters required-apparent water content of the distribution zone, and solute velocity and dispersion in the conveyance zone-GPFM was able to describe the breakthrough of solutes both through silty and sandy loam soils. Although both GPFM and CDM fitted the data well in visual, variables for GPFM were more realistic. The most sensitive parameter was the apparent water content, indicating that it is the determining factor to apply GPFM to various soil types, while Kim et al. (2005) reported that changing the velocity of GPFM reproduced solute transport when same soils were used. Overall, it seems that the GPFM has a great potential to predict solute leaching under field conditions with a wide range of generality.