• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.6
• /
• pp.875-883
• /
• 2006

The carbon and nitrogen removal process using PVA-gel (Polyvinyl Alcohol) immobilized microorganisms was studied. The process has been operated under diverse process conditions for 12 months. The process consists of denitrification with internal recycle of 300%, nitrification, aerobic digestion reactors and settling tank. Nitrificatoin and nitrogen removal efficiency according to gel packing ratio and temperature were studied. Yield for Heterotrophs ($Y_H$), decay coefficient for Heterotrophs($b_H$) in aerobic digestion reactor were determined to seize sludge reduction mechanism and compared with typical data of activated sludge process. Then SRT in aerobic digestion reactor was determined on an experimental basis and sludge reduction efficiency was calculated. The process was implemented successfully with sludge reduction efficiency of 92.0~98.5% on a basis of biomass.

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.326-332
• /
• 2018

In this study,the result shows that polyvinyl alcohol-sodium alginate (PVA-SA) gel bead crosslinked with sodium sulfate are better among the different methods by comparing the relative mechanical strength, mechanical strength swelling and expansion coefficient of beads in water. Subsequently, anammox biomass entrapment by PVA-SA gel was introduced into continuous stirred tank reactor (CSTR). After 24 operation days, the nitrogen removal efficiency achieved 60%, while the nitrogen loading rate (NLR) was $0.14kgN/m^3/d$ and the experiment data indicated that PVA-SA gel bead crosslinked with sodium sulfate can be used to initiate anammox process. Furthermore, it is an alternative for culturing anammox in a long-term operation.

• Journal of the Korean Chemical Society
• /
• v.55 no.6
• /
• pp.1024-1029
• /
• 2011

PVA/silica hybrid xerogels were synthesized by sonohydrolysis of a mixture of 2-way catalyzed TEOS and water solution of PVA. PVA was successfully removed from the xerogels through calcination and its removal was confirmed through TGA analysis of the calcined gel. Microstructure of the gels was studied through SEM, XRD and FTIR. Nitrogen sorption studies were conducted to find out surface area of different samples. It was found out that the samples having PVA removed through calcinations have higher surface area (411.64 $m^2$/g) than the samples (353.544 $m^2$/g) synthesized without any PVA. Adsorption properties of these xerogels synthesized by using different ratios of components were studied by taking Rhodamine G6 as a model adsorbate. The experiments were conducted at room temperature ($25^{\circ}C$). UV visible spectroscopy was used to measure the concentration of the dye before and after adsorption. The adsorption data of Rhodamine G6 on PVA modified silica is described by the Freundlich's adsorption model.

• Membrane Journal
• /
• v.6 no.4
• /
• pp.203-212
• /
• 1996

The operating parameters influencing on limiting flux was investigated in the ultrafiltration of PVA, and a new model, which is based on the Amiar model using the concept of heat transfer coefficient, was devised to overcome the limitation of gel-layer model. Using polysulfone plate-unit membrane (MWCO=20,000) and hollow-fiber membrane (MWCO= 30,000), ultrafiltration characteristics of PVA was examined with the variation of operating parameters such as cross flow velocity, transmembrane pressure, temperature, and PVA concentration. According to experimental results, the ultrafiltration of PVA through polysulfone membrane is mainly controlled by well-known phenomena of concentration polarization caused by gel-layer formation. On the contrary, in hollow fiber membrane was observed upward limiting flux which can not be explained by gel-layer model. New model was applied to predict the upward limiting flux behavior with partial satisfaction. The application of new model including viscosity correction factor, however, revealed that PVA ultrafiltration is closely related to the viscosity of permeating fluid.

• Current Optics and Photonics
• /
• v.7 no.1
• /
• pp.21-27
• /
• 2023

A highly sensitive optical-fiber humidity sensor is demonstrated in this paper. By using Nafion-PVA sol-gel and single-mode optical fibers, the Fabry-Perot humidity sensor is easily fabricated. In the humidity range of 29%-72%, humidity-response experiments are carried out with a cycle of rising and falling humidity to investigate humidity-response characteristics. The experimental results show 2.25 nm/%RH sensitivity and a 0.9997 linear correlation coefficient, with good consistency. The changes in optical-path difference (OPD) and free spectral range (FSR) with humidity are also discussed. The humidity sensitivities of a typical sensor are 80.3 nm/%RH (OPD) and 0.03 nm/%RH (FSR). Furthermore, many humidity sensors with different Nafion-PVA sol-gel concentration and initial cavity length are experimentally investigated for humidity response. The results show that the sensitivity increases with higher Nafion ratio of the Nafion-PVA sol-gel. The influence of changing cavity length on sensitivity is not obvious. These results are helpful to research on optical-fiber humidity sensors with good performance, easy fabrication, and low cost.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.6
• /
• pp.576-584
• /
• 2020

In order to obtain basic information for using polyvinyl alcohol (PVA) gel as a tissue mimicking phantom for temperature visualization, the temperature change characteristics due to the focused ultrasound were examined for different concentration of PVA. To obtain the basic acoustic characteristics, the speed of sound, the attenuation coefficient, and the density depending on the PVA concentration were measured, and the thermodynamic characteristics, such as thermal conductivity and heat capacity, were measured. The range of temperature rising in the vicinity of the focal point due to the focused ultrasound was observed using a thermochromic film that changes color at 30 degree or more, and the discolored area was obtained by image processing of the recorded image. As the concentration of PVA increases in the given range of 2 wt% ~ 16 wt%, the area that rises above 30 degree inside the gel increases linearly. It is confirmed that the discolored area increases as the power applied to the focused ultrasonic transducer increases. These results showed good agreement with the simulation results using the finite element method.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.792-802
• /
• 2002

In this study, hydrogels from mixtures of poly (vinyl alcohol) (PVA)/poly(N-vinylpyrrolidone) (PVP)/glycerin/chitosan were prepared by γ-ray irradiation and the mechanical properties such as gelation, water absorptivity, and gel strength were examined to evaluate the applicability of these for wound dressing. Then PVA:PVP was weight ratio of 6 : 4, the concentration of chitosan was 0.3 wt%, the concentration of glycerin was in the range of 0∼5 wt%t. The solid concentration of PVA/PVP/glycerin/chitosan solution was 15 wt%. Gamma irradiation doses of 25, 35, 50, and 60 kGy were exposed to a mixture of PVA/PVP/glycerin/chitosan to evaluate the effect of irradiation dose. Gel content and gel strength increased as glycerin concentration in PVA/PVP/glycerin/chitosan decreased, and as irradiation dose increased. Swelling degree increased as glycerin concentration in PVA/PVP/glycerin/chitosan increased, and as irradiation dose decreased. The glycerin in PVA/PVP/glycerini/chitosan hydrogel prevented the transformation of shape. These hydrogel dressings had better curing effect than vaseline gauge.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.04a
• /
• pp.135-137
• /
• 2008

PVA films with 1,2,3,4-Butanetetracarboxylic acid(BTCA) and sodium hypophosphite monohydrate(SHM) were crosslinked via thermal curing. Different parameters affecting on the crosslinking were investigated including BTCA and SHM concentration, curing temperature and time. The cured films was extracted with boiling water and gel fraction was calculated from weight change of the PVA films. Moisture regain of the gelled films was also measured. While the gel fraction of PVA films increased with increasing curing temperature and time, moisture regain decreased. Water resistance of the crosslinked PVA films improved by the BTCA crosslinking treatment.

• Microbiology and Biotechnology Letters
• /
• v.23 no.2
• /
• pp.203-208
• /
• 1995

The Polyvinyl alcohol (PVA) oxidase is a key enzyme involved in degradation of PVA with PVA hydrolase. The PVA oxidase has been purified to homogeneity from the culture broth of PVA grown Pseudomonas cepacia G5Y strain by ammonium sulfate precipitation, DEAE-cellulose column chromatography, and Sephadex G-150 gel filtration. The molecular weight of the purified enzyme was estimated about 60, 000 daltons by SDS-polyacrylamid gel electrophoresis. The enzyme is most active at 45$\circ$C and at pH 8.5, and is stable below 55$\circ$C and between pH 6 and 9. The enzyme activity was strongly inhibited by Ag$^{2+}$ and Hg$^{2+}$.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2009.11a
• /
• pp.15-16
• /
• 2009

Poly(vinyl alcohol) was crosslinked by UV irradiation in the presence of water soluble photoinitiators. The crosslinking of PVA films with 1,2,3,4-Butanetetracarboxylic acid(BTCA) and sodium phosphinate monohydrate(SPM) was also achieved via thermal curing. Different factors in the crosslinking including thermal and radiation methods were studied. Gel fraction of PVA films increased with increasing photoinitiator concentration. The maximum gel fraction on the crosslinking method was reached about 81%. The glass transition and maximum decomposition temperature improved by both thermal and radiation crosslinking.