• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1997년도 제13회 학술발표회 논문개요집
• /
• pp.69-69
• /
• 1997

• 한국전기전자재료학회논문지
• /
• 제36권4호
• /
• pp.362-368
• /
• 2023

Multilayered actuators using Pb(Mg_1/3Nb_2/3)O₃-Pb(In_1/2Nb_1/2)O₃-PbTiO₃ (PMN-PIN-PT) crystals have demonstrated excellent properties, but are costly and lack mechanical strength. Textured PMN-PIN-PT ceramics exhibit robust mechanical strength and comparable properties to their single crystals form. However, the development of multilayered actuators using textured PMN-PIN-PT ceramics has not been achieved until now. This study presents the development of a multilayered actuator using textured 0.37PMN-0.29PIN-0.34PT ceramics with an Ag_0.9/Pd_0.1 inner electrode, co-fired at 950℃. A random 0.37PMN-0.29PIN-0.34PT ceramics multilayered actuator was also developed for comparison. The multilayered actuator consisted of 9 ceramic layers (36 ㎛ thickness) with an overall actuator thickness of 0.401 mm. The textured and random 0.37PMN-0.29PIN-0.34PT ceramics-based multilayered actuators achieved displacements of 0.61 ㎛ (0.15% strain) and 0.23 ㎛ (0.057% strain) at a low applied peak voltage of 100 V. These results suggest that the developed multilayered actuator using high-performance textured 0.37PMN-0.29PIN-0.34PT ceramics has the potential to replace expensive single crystal-based actuators cost-effectively.

• 한국진공학회지
• /
• 제17권2호
• /
• pp.122-129
• /
• 2008

Perovskite 구조의 PMT-PT계 고용체를 precursor columbite를 이용한 산화물 혼합법으로 제작하여 결정립의 성장과 상전이 현상을 분석하였다. $1250^{\circ}C$에서 4시간 유지하여 제작한 시편의 소결밀도는 이론밀도의 97% 이상이었고, 완전한 perovskite phase를 형성하였다. 치밀하게 소결 처리된 시편의 결정립의 크기는 $6\sim8{\mu}m$로 측정되었다. PMT-PT 고용체계는 복합 강유전 고용체의 전형적인 P-E 이력현상과 강한 진동수 분산특성이 관찰되었다. 특히 PMT가 70% 이하인 조성은 상전이 온도 이상에서도 자발분극이 완전히 소멸하지 않는 relaxor 특성을 보였으며, 유전상수와 유전손실의 큰 진동수 의존성을 보였다.

• The Korean Journal of Ceramics
• /
• 제3권1호
• /
• pp.52-56
• /
• 1997

The Pt doped $TiO_2$ composite membranes were prepared by the sol-gel process. The Pt doped titania sol was peptized with hydrochloric acid in the pH range of 1.23 to 1.32 at 5$0^{\circ}C$. The average particle size of the Pt doped titania sol was shown to be below 15nm and well dispersed in the solution. XPS show the Pt elements continuous and homogeneous dispersed in the $TiO_2$ membrane. The mean particle size of the Pt doped $TiO_2$ composite membrane has smaller than that of the undoped $TiO_2$ composite membrane. The average pore size of the Pt doped $TiO_2$ composite membrane was increased from 58 to 193 $\AA$ with firing temperature changed from 550 to 85$0^{\circ}C$. It was observed that the Pt doped $TiO_2$ composite membranes showed crack-free and homogeneous microstructue as well as narrow particle size distribution up to above 75$0^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• 제25권6호
• /
• pp.843-846
• /
• 2004

Pt nanoparticles loaded on alumina through an impregnation at room temperature was prepared using $K_2PtCl_4$ and acrylic acid as capping material. Transmission electron microscopy showed that the deposited Pt particles indicate ca. 80% cubic shapes with a narrow distribution of 8-10 nm in size. Propylene hydrogenation over the catalyst has been carried out to evaluate their catalytic performance by the values of activation energy. It is determined from the initial rate, reaction order, and rate constant and is found to be $9.7{\pm}0.5$ kcal/mol. This value has been discussed by comparing to those of encapsulated- and truncated octahedral Pt nanoparticles deposited on alumina, respectively, to study influence of the particle size and shape, and capping material used on the activation energy.

• 한국결정성장학회지
• /
• 제12권1호
• /
• pp.1-6
• /
• 2002

본 연구에서는 금속 알콕시드를 이용하여 0.9PMN-0.1PT 소결체를 제조하는데 있어 과량으로 첨가되는 $Mg(OC_2H5)_2$, Pb$(CH_3COO)_2{\cdot}3H_2O$ 등이 페로브스카이트 상의 생성량과 소결 밀도, 유전 상수 등에 미치는 영향을 검토하였다. 졸-겔법으로 0.9PMN-0.1PT 세라믹을 제조함에 있어 $Mg(OC_2H5)_2$를 과량 첨가하는 경우 페로브스카이트 상의 생성율을 증가시키는 효과가 나타났다. 0.9PMN-0.1PT 조성에 $Mg(OC_2H5)_2$를 5wt% 과잉 텀가한 시편을 $1,150^{\circ}C$에서 1시간 소결한 경우 페로브 스카이트 단일상을 얻었으며 이 때의 밀도는 이론 밀도의 98%인 것으로 확인되었다. $1.150^{\circ}C$에서 1시간 유지하여 소결한 시편의 유전 상수는 $Mg(OC_2H5)_2$를 5wt% 과잉 첨가한 경우 증가하였으며, 주파수 1 kHz에서 최대 유전 상수는 15,000의 값을 가졌다.

• The Korean Journal of Ceramics
• /
• 제6권4호
• /
• pp.348-353
• /
• 2000

The effects of MnO$_2$ and Fe$_2$O$_3$ on the piezoelectric properties of 0.05PMN-0.451PT-0.499PZ ceramics were investigated. The addition of MnO$_2$ increased mechanical quality factor (Q$_m$) but decreased the dielectric constant (K$^{T}_{33}$) and compliance (S$^{E}_{11}$) of the specimens. These results indicated that MnO$_2$ behaves as an acceptor in 0.05MN-0.451PT-0.499PZ ceramics. The electromecanical coupling coefficient (K$_P$) of 0.05PMN-0.451PT-0.499PZ ceramics slightly increased with the addition of MnO$_2$ however, the enhancement of $K_P$ was insignificant. A small amount of Fe$_2$O$_3$ was added to enhance the $K_P$ of the 0.05PMN-0.451PT-0.499PZ + 0.5 wt% MnO$_2$ ceramics. The addition of Fe$_2$O$_3$ largely increased $K_P$ through the increase of the K$^{T}_{33}$ and the polarization. The mechanical quality factor of the specimens decreased with the addition of Fe$_2$O$_3$however, the reduction was negligible.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1510-1512
• /
• 1997

Piezoelectric characteristics of lead zirconate(PZ)-lead titanate(PT)-lead manganese antimony(PMS) ceramics with the various changes of calcination temperature in PMS were prepared. The range of their sintering temperature was from $1100^{\circ}C$ to $1250^{\circ}C$. The electro-mechanical properties of PZ-PT-PMS ceramics such as piezoelectric constant, electro-mechanical coupling coefficient, and mechanical quality factor are measured as a function of the calcination temperature of PMS. As increasing the calcination temperature of PMS mechanical quality factor is increased.

• 한국전기전자재료학회논문지
• /
• 제29권8호
• /
• pp.476-482
• /
• 2016

Convectional PZT based piezoelectric ceramics have to sinter at high temperature about $1,200^{\circ}C$ for their suitable electrical properties. However, some issues: low temperature sintering piezoelectric ceramic composition and reliable internal electrode, have recently attracted a great deal of interest as a highly efficient multi-layered piezoelectric ceramics. In order to optimize low temperature sintering conditions of thick-film PMN-PZ-PT ceramic, it was investigated sintering and piezoelectric properties according to the change of $LiBiO_2$ contents. Thus, the superior piezoelectric properties were found at the pallet type PMN-PZ-PT optimized with low sintering processing at $925^{\circ}C$ including 7 wt% $LiBiO_2$ sintering aid. Consequentially, we successfully manufactured thick-film PMN-PZ-PT ceramics, which had superior piezoelectric and dielectric properties, with 5 wt% of $LiBiO_2$ sintering aid at temperature of $900^{\circ}C$.

• 한국세라믹학회지
• /
• 제55권2호
• /
• pp.166-173
• /
• 2018

In order to investigate the effect of Mn on the dielectric and piezoelectric properties of PMN-PT [$Pb(Mg_{1/3}Nb_{2/3})O_3-PbTiO_3$], four different types of 71PMN-29PT samples were prepared using the solid-state single crystal growth (SSCG) method: (1) Undoped single crystals, (2) undoped polycrystalline ceramics, (3) Mn-doped single crystals, and (4) Mn-doped polycrystalline ceramics. In the case of single crystals, the addition of 0.5 mol% Mn to PMN-PT decreased the dielectric constant ($K_3{^T}$), piezoelectric charge constant ($d_{33}$), and dielectric loss (tan ${\delta}$) by about 50%, but increased the coercive electric field ($E_C$) by 50% and the electromechanical quality factor ($Q_m$) by 500%, respectively. The addition of Mn to PMN-PT induced an internal bias electric field ($E_I$) and thus specimens changed from piezoelectrically soft-type to piezoelectrically hard-type. This Mn effect was more significant in single crystals than in ceramics. These results demonstrate that Mn-doped 71PMN-29PT single crystals, because they are piezoelectrically hard and simultaneously have high piezoelectric and electromechanical properties, have great potential for application in fields of SONAR transducers, high intensity focused ultrasound (HIFU), and ultrasonic motors.