• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.228-231
• /
• 2002

We report the effect of density of thin films on moisture adsorption and hydration of MgO thin film, usually used as a protective layer in AC-PDP After hydration, lots of hemispherical shaped clusters, $Mg(OH)_2$, formed on the surface of MgO thin films. However clusters formed on low-density thin films were bigger than those on high-density films. From ERD spectra, it seemed that the concentration of hydrogen was very high in the region 20 nm from the surface of MgO thin film. The low-density thin film had more hydrogen than high-density thin film. From simulation results of ERD and RBS it was found that hydration reaction also occurred in the inner part of the film. So diffusion of Mg atoms from the inner part of the film to the surface and $H_2O$ molecules from the surface to the inner part of the film is important. And because low density thin film has many short paths for diffusion of Mg atoms and $H_2O$ molecules, low-density thin film is more hydrated. So to suppress hydration of MgO thin films, high-density thin film is needed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.143-146
• /
• 2003

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure and discharge power on the electrical, optical and morphological properties were investigated experimentally. The consideration on the effect of doping amounts of Al on the electrical and optical properties of ZnO thin film were also carried out. ZnO:Al films with the optimum growth conditions showed resistivity of $9.42{\times}10^{-4}\;{\Omeg}-cm$ and transmittance of 90.88% for 840nm in film thickness in the wavelength range of the visible spectrum.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.862-869
• /
• 2006

The purpose of this study is to propose the proper vocabularies for evaluating H.D TV set fan noise in residential condition. To achieve this goal, psycho-acoustic experiments were carried out with TV set fan noise modulated at specific frequency band. finally, a correlation analysis between vocabularies, and a factor analysis of psycho-acoustical responses were conducted. As a result of this study, followings are suggested. Analyzing the psycho-acoustical response corresponding to the various sound level, the higher the sound levels, the higher the response values were. It is estimated that the sound level determined psycho-acoustical responses. On the degree of response to fan noise, the initial level of negative feeling is located on $35{\sim}40$ dB(A). The factor of evaluating H.D. TV set fan noise has induced three the appropriate korean adjectives; Irritate, Monotonous, stuffy and dryness. The result of this study may be used to evaluate the acoustic threshold level for indoor noise or a basis for specifying the desired acoustic environment of dwellings.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.10 s.115
• /
• pp.1014-1023
• /
• 2006

The purpose of this study is to propose the proper vocabularies for evaluating H.D TV set fan noise. To achieve this goal, psycho-acoustic experiments were carried out with TV set fan noise modulated at specific frequency band. Finally, a correlation analysis between vocabularies, and a factor analysis of psycho-acoustical responses were conducted. As a result of this study, followings are suggested. Analyzing the psycho-acoustical response corresponding to the various sound level, the higher the sound levels, the higher the response values were. It is estimated that the sound level determined psycho-acoustical responses. On the degree of response to fan noise, the initial level of negative feeling is located on $35{\sim}40$ dB(A). The factor of evaluating H.D. TV set fan noise has induced three the appropriate korean adjectives; Irritate, Monotonous, stuffy and dryness. The result of this study may be used to evaluate the acoustic threshold level for indoor noise or a basis for specifying the desired acoustic environment of dwellings.

• Korean Journal of Materials Research
• /
• v.13 no.8
• /
• pp.509-513
• /
• 2003

In the present investigation, $La^{3＋}$ and $Ce^{V}$ ions were substituted for $Y^{3＋}$ in the $YBO_3$: Tb in various concentrations. It has been found that these phosphors form solid solutions within limited concentration ranges Excitation and emission spectra under 254 nm and 147 nm were investigated for these phosphors to evaluate influences of $La^{3＋}$ and $Ce^{3＋}$ ions on brightness and CIE color coordinates. It has been observed that brightness of $(Y, La)BO_3$: Tb under 254 nm and 147 nm when $La^{3＋}$ ions are added show an increase of 2.7 times and 1.25 times, respectively. On the other hand, emission intensities of peaks in $Y_{0.8-x}$ $BO_3$: $Tb_{0.2}$ , $Ce_{x}$ show continuos decrease as $Ce^{3＋}$ / content is increased from 0 to 0.4. CIE color coordinates of prepared phosphors show yellowish green which is needed to be improved to be used for display applications.

• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.752-756
• /
• 2002

Green-emitting $Zn_2SiO_4:Mn$ phosphors for PDP(Plasma Display Panel) application were synthesized by colloidal seed-assisted spray pyrolysis process. The codoping with $Gd^{3+}/Li^+$, which replaces $Si^{4+}$ site in the willemite structure, was performed to improve the luminous properties of the $Zn_2SiO_4:Mn$ phosphors. The particles prepared by spray pyrolysis process using fumed silica colloidal solution had a spherical shape, small particle size, narrow size distribution, and non-aggregation characteristics. The $Gd^{3+}/Li^+$ codoping amount affected the luminous characteristics of $Zn_2SiO_4:Mn$ phosphors. The codoping with proper amounts of $Gd^{3+}/Li^+$ improved both the photoluminescence efficiency and decay time of $Zn_2SiO_4:Mn$ phosphor particles. In spray pyrolysis, the post-treatment temperature is another factor controlling the luminous performance of $Zn_2SiO_4:Mn$ phosphors. The $Zn_{1.9}SiO_4:Mn_{0.1}$ phosphor particles containing 0.1 mol% $Gd^{3+}/Li^+$ co-dopant had a 5% higher PL intensity than the commercial product and 5.7 ms decay time after post-treatment at $1,145^{\circ}C$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.2
• /
• pp.168-172
• /
• 2014

A new sustain driving method is proposed to improve luminous efficiency by the generation of the self-erasing discharge during a sustain period in AC plasma display panel. As one subfield time in the conventional AC PDP is divided into the reset, address, and sustain period. Among them, as the square sustain waveform is alternately applied to the X and Y electrodes on the front plate during the sustain period, the plasma discharge for displaying the image is continuously produced. Meanwhile, in the conventional driving method, the address waveform applied to the A electrode on the rear plate is only driving during an address period and grounded during a sustain period. In this experiment, the negative pulse is applied to the A electrode at the latter part of the sustain pulse for improving the luminous efficiency producing the self-erasing discharge during the sustain period. The negative pulse on the A electrode can change from the space to the wall charge and induce the additional discharge by the accumulated wall charge when the voltages of three electrodes are grounded. As a result, the luminous efficiency will be measured with changes in the voltage level of the A electrode and the new driving method can be improved to the luminous efficiency about 32 % compared with the conventional driving method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.9
• /
• pp.681-684
• /
• 2010

The $TiO_2$/ZnS/Ag/ZnS/$TiO_2$ multilayered structure for the transparent electrodes in plasma display panel was designed by essential macleod program (EMP) and the multilayered film was deposited on a glass substrate by direct-current (DC)/radio-frequency (RF) magnetron sputtering system. During film deposition process, the Ag layer in $TiO_2$/Ag/$TiO_2$ structure became oxidized and the filter characteristic was degraded easily. In this study, ZnS layer was adopted as a diffusion blocking layer between $TiO_2$ and Ag to prevent the oxidation of Ag layer efficiently in $TiO_2$/ZnS/Ag/ZnS/$TiO_2$ structure. Based on the AES depth profiling analysis, the Ag layer was effectively protected by the ZnS layer as compared with the $TiO_2$/Ag/$TiO_2$ multilayered films without ZnS as an antioxidant layer. The 3 times stacked $TiO_2$/ZnS/Ag/ZnS/$TiO_2$ films have low sheet resistance of $1.22{\Omega}/{\square}$ and luminous transmittance was as high as 62% in the visible ranges.

• Journal of the Korean Vacuum Society
• /
• v.8 no.1
• /
• pp.70-74
• /
• 1999

MgO-CaO protective layers with various composition were prepared by electron beam evaporation to improve the characteristics of conventional pure MgO thin films as a protective layer for AC-PDP. The maximum deposition rate of pure MgO was 1025 $\AA$/min and decreased with increasing [(CaO/(MgO+CaO)] ratio of evaporation starting materials. From XRD analyses, a trend of peak shift to the lower 2$\theta$ angle side was shown as CaO content increased and it stoped when the concentration of CaO was 0.13, which corresponds to the maximum solubility of CaO in MgO. The optimum composition of the protective thin films was Mg 47.1 at%, Ca 1.3 at%, O 51.6 at%, and firing voltage, memory margin and deposition rate of the film with this composition was 176 V, 0.5 and 515 $\AA$/min, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.1
• /
• pp.135-139
• /
• 2015

The address discharge time lags are investigated in each subfield time in AC plasma display panel and a modified driving waveform is proposed to reduce the address discharge time lag by applying different additional scan voltage under no misfiring discharge production. The weak plasma discharge in AC PDP is generated by applying high positive-going ramp waveform to the scan electrode during the first reset period and that induce the production of the priming particle and wall charge. Because the wall charge becomes the wall voltage in a cell, the wall plus external address voltage produce the address discharge. However, as the wall charge in a cell is gradually disappeared as time passed, the address discharge time in the subfield time for 1 TV frame is lagged. In the first subfield time, the address discharge is faster produced than the other subfield time because the wall charge are much remained by the high positive-going ramp voltage during the reset period in the first subfield time. Meanwhile, from the second to last subfield, the address discharge production time is gradually delayed due to the dissipation of the wall charge in a cell. In this study, the address discharge time lags are measured in each subfield time and the total address discharge time lags are shortened by applying the different additional scan voltage during the address period in each the subfield time.