• 콘크리트학회논문집
• /
• 제26권2호
• /
• pp.125-133
• /
• 2014

이 연구에서는 볼트접합 및 프리스트레스를 적용한 프리캐스트 콘크리트 보-기둥 외부접합부의 내진 및 구조적 성능을 평가하였다. 총 5개의 보-기둥 외부접합부 실험체를 제작하고 보 단부에 변위제어 방식으로 반복하중을 가하며 실험을 수행하였다. 이 연구의 결과를 근거로 다음과 같은 결론을 얻을 수 있었다. 완전 건식공법이 적용된 PC 접합부는 완전 습식공법이 적용된 RC 접합부보다 에너지소산이나 핀칭현상에 있어서 불리한 거동을 보였지만 이는 설계과정에서 의도된 현상이며, 횡변형 능력에 있어서는 우수한 결과를 보였다. 또한 층간변위비 4%까지 횡하중 저항성능의 손실이 발생하지 않았고 매설용너트에 항복이 집중되는 메커니즘을 보이는 점으로 미루어 볼 때 개발된 접합부는 외부접합부 횡저항시스템으로서 적합한 것으로 사료된다. 추가적인 프리스트레스는 PC 접합부의 과도한 핀칭현상 방지 및 접합부 균열제어에 효과적이었으며 PC 접합부의 전체적인 내진성능을 향상시켰다.

• Computers and Concrete
• /
• 제32권3호
• /
• pp.339-349
• /
• 2023

Fast-built construction is a key feature for successful applications of precast concrete (PC) moment frame system in recent construction practices. To this end, by introducing some unique splicing details in precast connections, especially between PC columns including panel zones, use of temporary supports and bracings can be minimized based on their self-sustaining nature. In addition, precast wide beams are commonly adopted for better economic feasibility. In this study, three self-sustaining precast concrete (PC) wide beam-column connection specimens were fabricated and tested under reversed cyclic loadings, and their seismic performances were quantitatively evaluated in terms of strength, ductility, failure modes, energy dissipation and stiffness degradation. Test results were compared with ASCE 41-17 nonlinear modeling curves and its corresponding acceptance criteria. On this basis, an improved macro modeling method was explored for a more accurate simulation. It appeared that all the test specimens fully satisfy the acceptance criteria, but the implicit joint model recommended in ASCE 41-17 tends to underestimate the joint shear stiffness of PC wide beam-column connection. While, the explicit joint model along with concentrated plastic hinge modeling technique is able to present better accuracy in simulating the cyclic responses of PC wide beam-column connections.

• 토지주택연구
• /
• 제5권2호
• /
• pp.91-97
• /
• 2014

일반적으로 부분 PC 구조에서는 기둥, 보, 그리고 하프 PC 슬래브 등을 공장에서 제작하여 현장에서 조립한 후에 덧침 콘크리트의 타설에 의하여 일체화한다. 따라서 PC 부재가 연결되는 위치에서의 불연속면과 함께 PC 부재의 조립을 위한 걸침길이 확보와 같은 접합부 형상 등으로 인하여 접합부 보강을 위한 구조설계가 필요하다. 보-기둥 접합부에서 발생하는 PC 부재와 덧침 콘크리트 사이의 접합면에서 전단력 전달 성능은 접합부의 구조 성능에 큰 영향을 미치게 된다. 서로 다른 두 개의 부재가 만나는 면에서는 부재간의 미끄러짐(slip) 현상과 전단력이 발생되는데, 본 연구에서의 접합면 전단에 대해서는 실험을 수행하고 실험결과에 대해 ACI 기준 및 PCI 설계식을 활용하여 검토하였다. 보-기둥 접합부에 대한 접합면 전단 설계를 ACI 기준 또는 PCI 설계법에 따라 검토한다면, 구조성능을 확보할 수 있는 것으로 확인되었다. 또한 실험결과를 고찰하면 보-기둥 접합부에서 PC 보의 걸침길이를 30mm로 하여도 구조적인 문제는 없는 것으로 판단된다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 춘계학술논문 발표대회 제6권1호
• /
• pp.9-13
• /
• 2006

The purpose of this study was to introduce the applied care of PC beam-column interior joint with splice type rebar. In this case, although the erection time of the introduced case was a little bit higher than that of general precast concrete method, this method was more effective than general precast concrete method in aspect of direct cost and the number of column joint. Therefore, this method could be adopted in the construction of the commercial and residential building in the future.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.539-544
• /
• 2000

The purpose of this study is to develop the mechanical anchorage, namely MAB-BOP (Mechanical Anchorage of 90$^{\circ}$ Hooked Bars with BOlt nad Plate) of the beam-column joint in precast concrete framed structures. Six specimens simulating typical interior beam-column joints were tested to investigate the mechanical characteristics of MAB-BOP. Of primary interest was the measurement of the slip of the anchored bar. Th load-slip curve obtained from this test were used to compare the mechanical performances of the different anchoring methods. Based on the test results, it was found that MAB-BOP showed sufficient anchoring strength capacity compared to 90$^{\circ}$ hooked bar method. So, MAB-BOP can be used as the anchoring methods of the reinforcing bars in PC beam-column joint.

• KIEAE Journal
• /
• 제7권6호
• /
• pp.113-118
• /
• 2007

The composite beam adopted in the study was designed to reduce the floor height as well as to embed the top flange of steel frame into the slab that will enable to avoid applying the fire-resistant coating and to unify the joint method with a steel frame-type. As the steel frame and bottom concrete of the beam is pre-fabricated at the factory it could reduce the overall schedule at the jobsite. Applying such composite beam system to the work is expected to provide the efficient and enhanced performance, given the current tendency of the building construction that tends to be getting higher, larger and dense. The study focused on combining the composite beam with various column systems in a bid to propose the details thereof. A desirable composite girder can be adopted depending on site conditions through the evaluation of various beam and jointing approaches. Among the column systems applied to the study are steel column, SRC column, RC-PC column and RC column. The ways of combining with the columns addressed in the study were categorized into the rigid joint, pin joint, steel frame joint and bracket type joint. Besides, the instruction for site fabrication of beam-column was added in an effort to help set up the site fabrication procedures.

• 콘크리트학회논문집
• /
• 제26권4호
• /
• pp.545-553
• /
• 2014

이 연구는 PC 보-기둥 접합부의 일반적인 거동의 접합 상세에 따른 통합적 평가 방안을 제안하였다. 이 연구는 접합부의 파괴 패턴과 이에 연관된 접합부 상세의 특징을 정량적으로 표현하기 위해 접합부와 각 요소들이 보유한 변형기여분을 사용할 것을 제안하였다. 이에 따라 PC 접합부는 '일체식 접합부'와 '연결식 접합부'로 크게 분류되었다. 접합부의 분류를 위한 기준 사항의 제안 및 검증을 위해 네 개의 보-기둥 실험체의 실험을 수행하였다. 실험은 일반적인 보-기둥 접합부의 실험 방법과 같은 방법으로 진행되었다. 가력은 접합부 상부 기둥의 끝단에서 수행되었으며, 보 양단은 힌지로 고정되었다. 변형기여분의 평가를 위해 총 34개의 LVDT가 주요 변형이 발생할 것으로 예상되는 곳에 설치되었다. 실험 결과 세 개의 실험체에서 나타난 각 요소들의 변형기여분은 수치적으로 다른 특성을 가지고 있는 것을 확인할 수 있었다. 실험 결과를 기반으로 접합부의 변형 정도와 다른 요소들의 변형 정도에 의거하여, 접합부의 변형이 적고 보의 휨 변형이 크게 나타나는 강한 접합부와 접합부의 변형이 용인되는 연성 접합부로 일체식 접합부를 분류할 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 춘계 학술논문 발표대회
• /
• pp.10-11
• /
• 2013

Green Frame is a column-beam system formed by composite precast concrete column and beam connected with steel buried in both members. During the installation of Green columns, the columns of Green Frame, covering 3 floors per each piece and beams, the eccentricity can be observed due to the construction error and the weight of beam itself. Such eccentricity may have a little influence on a single frame, yet, it can develop critical issues to the installation of subsequent beams or beams on the upper floors in the context of a building as a whole that has multiple frames. These issues lead to delay in frame installation, decrease of productivity and increase of cost, etc. Therefore, this study presents a steel-joint connection method in order to solve the issues. The steel-joint connection method exists on slope plane and reinforcing plate in steel frame buried in composite PC members. Through this method, the issues can be resolved without requiring additional equipment or manpower.

• Earthquakes and Structures
• /
• 제21권6호
• /
• pp.653-667
• /
• 2021

In this study, cyclic loading tests were conducted on the precast concrete (PC) wide beam (WB)-column joints. Two beam-column joint specimens were fabricated with the arrangement and anchorage details of the reinforcing bars penetrating the beam and column as variables. Through a cyclic loading test, the lateral load-story drift ratio responses, seismic performance characteristics (e.g., ductility, overstrength factor), energy dissipation, strength and stiffness degradations of each specimen were compared and analyzed based on the various indices and the current structural codes (ACI 318-19 and ACI 374.1-05 report). In addition, the shear lag effect was confirmed through the gauge values of the PC beam, and the differences in seismic performance between the specimens were identified on that basis.

• 한국강구조학회 논문집
• /
• 제8권4호통권29호
• /
• pp.85-94
• /
• 1996

This paper investigated structural behaviors of joint of concrete filled steel tube column and P.C reinforced concrete beam through a series of hysteretic behavior experiment. The results are summarised as follows: (1) The joint stiffness of concrete filled square steel tube column and P.C reinforecd beam was higher than that of concrete filled circular steel tube column and P.C reinforecd beam, and it was decreased as the increase of the number of hysteretic cycle. (2) The aspects of the hysteretic behavior in the joint was stable as the increase of the number of hysteretic cycle, and rotation resisting capacity of joint of concrete filled square steel tube column and P.C reinforced concrete beam was higher than those of the concrete filled circular steel tube column and P.C reinforced concrete beam. (3) Some restriction must be put upon the ratio of axial force in this joint model because the load carrying capacity was decreased by flexural and flexural-torsional buckling in case of the ratio of axial force 0.6. (4) The emprical formula to predict the ultimate capacity of joint model to superimpose shearing strength of steel web(H section) and bending strength of reinforced concrete beam was expected.