• Economic and Environmental Geology
• /
• v.25 no.1
• /
• pp.27-39
• /
• 1992

Several pyrophyllite deposits occur around the Milyang area where Cretaceous andesitic rocks and spatially related granitic rocks are widely distributed. Pyrophyllite ores consist mainly of pyrophyllite, and quartz with small amount of sericite, pyrite, dumortierite, and diaspore. The andesitic rocks and spatially related granitic rocks in this area suggest that they could be formed from the same series of a calc-alkaline magma series. The contents of $SiO_2$, $Al_2O_3$, LOI(loss on ignition) are enriched, and $K_2O$, $Na_2O$, CaO, MgO, $Fe_2O_3$ are depleted in altered andesitic rocks and ores. Enrichment of As, Cr, Sr, V, Sb and depletion of Ba, Cs, Ni, Rb, U, Y, Co, Sc, Zn are characteristic during mineralization. The pyrophyllite ores can be discriminated from the altered-and unaltered wall-rocks by an increasing of $(La/Lu)_{cn}$ from 4.18~22.13 to 8.98~55.05. In R-mode cluster analysis, Yb-Lu-Y, La-Ce-Hf-Th-U-Zr, $TiO_2-V-Al_2O_3$, Sm-Eu, $CaO-Na_2O-MnO$, Cu-Zn-Ag, $K_2O-Rb$ are closely correlated. In the discriminant analysis of multi-element data, $P_2O_5$, As, Cr and $Fe_2O_3$, Sr are helpful to identify the ores from the unaltered-and altered wall-rocks. In the factor analysis, the factors of alteration of andesitic rocks and ore mineralization were extracted. In the change of ions per unit volume, $SiO_2$, $Al^{3+}$ and LOI are enriched and $Na^+$, $K^+$, $Ca^{2+}$, $Mg^{2+}$, $Mn^{2+}$ and $Fe^{3+}$ are depleted during the alteration processes. The Milyang and the Sungjin pyrophyllite deposits could be mineralized by hydrothermal alteration in a geochemical condition of low activity ratio of alkaline ions to hydrogen ion with reference to spatially related granitic rocks.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.177-180
• /
• 2002

Thickness dependence of crystallographic orientation of diol based sol-gel derived PZT(52/48) films on dielectric and piezoelectric properties was investigated The thickness of each layer by one time spinning was about 0.2 $\mu\textrm{m}$, and crack-free films was successfully deposited on 4 inches Pt/Ti/SiO$_2$/Si substrates by 0.5 mol solutions in the range from 0.2 $\mu\textrm{m}$ to 3.8 $\mu\textrm{m}$. Excellent P-E hysteresis curves were achieved without pores or any defects between interlayers. As the thickness increased , the (111) preferred orientation disappeared from 1$\mu\textrm{m}$ to 3 $\mu\textrm{m}$ region, and the orientation of films became random above 3 $\mu\textrm{m}$. Dielectric constants and longitudinal piezoelectric coefficient d$\_$33/, measured by pneumatic method were saturated around the value of about 1400 and 300 pC/N respectively above the thickness of 0.8 7m. A micromachined piezoelectric cantilever have been fabricated using 0.8 $\mu\textrm{m}$ thickness PZT (52/48) films. PZT films were prepared on Si/SiN$\_$x/SiO$_2$/Ta/Pt substrate and fabricated unimorph cantilever consist of a 0.8 fm thick PZT layer on a SiNx elastic supporting layer, which becomes vibration when ac voltage is applied to the piezoelectric layer. The dielectric constant (at 100 kHz) and remanent polarization of PZT films were 1050 and 25 ${\mu}$C/$\textrm{cm}^2$, respectively. Electromechanical characteristics of the micromachined PZT cantilever in air with 200-600 $\mu\textrm{m}$ lengths are discussed in this presentation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.139-139
• /
• 2010

금속 실리사이드 나노입자는 열적 및 화학적 안정성이 뛰어나고, 절연막내에 일함수 차이에 따라 깊은 양자 우물구조가 형성되어 비휘발성 메모리 소자를 제작할 수 있다. 그러나 단일 $SiO_2$ 절연막을 사용하였을 경우 저장된 전하의 정보 저장능력 및 쓰기/지우기 시간을 향상시키는 데 물리적 두께에 따른 제한이 따른다. 본 연구에서는 터널장벽 엔지니어링을 통하여 물리적인 두께는 단일 $SiO_2$ 보다는 두꺼우나 쓰기/지우기 동작을 위하여 인가되는 전기장에 의하여 상대적으로 전자가 느끼는 상대적인 터널 절연막 두께를 감소시키는 방법으로 동작속도를 향상 시킨 $SiO_2/Si_3N_4/SiO_2$ 및 $Si_3N_4/SiO_2/Si_3N_4$ 터널 절연막을 사용한 금속 실리사이드 나노입자 비휘발성 메모리를 제조하였다. 제조방법은 우선 p-type 실리콘 웨이퍼 위에 100 nm 두께로 증착된 Poly-Si 층을 형성 한 이후 소스와 드레인 영역을 리소그래피 방법으로 형성시켜 트랜지스터의 채널을 형성한 이후 그 상부에 $SiO_2/Si_3N_4/SiO_2$ (2 nm/ 2 nm/ 3 nm) 및 $Si_3N_4/SiO_2/Si_3N_4$ (2 nm/ 3 nm/ 3 nm)를 화학적 증기 증착(chemical vapor deposition)방법으로 형성 시킨 이후, direct current magnetron sputtering 방법을 이용하여 2~5 nm 두께의 $WSi_2$ 및 $TiSi_2$ 박막을 증착하였으며, 나노입자 형성을 위하여 rapid thermal annealing(RTA) system을 이용하여 $800{\sim}1000^{\circ}C$에서 질소($N_2$) 분위기로 1~5분 동안 열처리를 하였다. 이후 radio frequency magnetron sputtering을 이용하여 $SiO_2$ control oxide layer를 30 nm로 증착한 후, RTA system을 이용하여 $900^{\circ}C$에서 30초 동안 $N_2$ 분위기에서 후 열처리를 하였다. 마지막으로 thermal evaporator system을 이용하여 Al 전극을 200 nm 증착한 이후 리소그래피와 식각 공정을 통하여 채널 폭/길이 $2{\sim}5{\mu}m$인 비휘발성 메모리 소자를 제작하였다. 제작된 비휘발성 메모리 소자는 HP 4156A semiconductor parameter analyzer와 Agilent 81101A pulse generator를 이용하여 전기적 특성을 확인 하였으며, 측정 온도를 $25^{\circ}C$, $85^{\circ}C$, $125^{\circ}C$로 변화시켜가며 제작된 비휘발성 메모리 소자의 열적 안정성에 관하여 연구하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.325-325
• /
• 2008

스크린 프린팅에 의한 압전 후막은 MEMS 공정을 이용하여 마이크로 펌프, 마이크로 벨브, 마이크로 센서, 마이크로 로봇 등 여러 초소형 기계부품에 응용되고 있으며, Sol-Gel, PLD를 이용해 증착된 막 등에 비해 수십${\mu}m$의 비교적 두꺼운 막을 형성시킬 수 있는 장점을 가지고 있다. 그러나 실리콘 기판을 사용하여 스크린 프린팅으로 형성된 압전 후막의 경우, 공정상 바인더를 연소시키는 과정을 거치게 되므로, 밀집된(Dense) 구조를 가지는 막을 만들기가 어렵다. 이로 인해 스크린 프린팅에 의한 후막은 전기적 특성 및 기계적 특성이 떨어지는 경향이 있다. 본 연구에서는 스크린 프린팅에 의한 압전 후막의 밀집된 구조 및 특성을 향상시키기 위해 0.01Pb$(Mg_{1/2}W_{1/2})$O3-0.41Pb$(Ni_{1/3}Nb_{2/3})O_3-0.35PbTiO_3-0.23PbZrO_3$의 powder와 Attrition 밀링 처리된 powder를 비율별로 혼합하여 입자의 크기를 변화시켜 막의 충진 밀도를 향상시켰으며, 열처리 효과를 극대화시키기 위해 RTA(Rapidly Thermal Annealing)를 통해 열처리 하였다. Attrition 밀링에 의한 파우더를 각각 비율별로 100%, 50%, 25%로 혼합하여 만든 압전 세라믹 페이스트는 P-type(100)Si Wafer sample 위에 $1{\mu}m$의 하부전극용($1100^{\circ}C$) Ag 전극을 screen print하여 소결했다. 그리고 다시 전극이 형성된 Si wafer 위에 스크린 프린팅하고, 건조 한 후 RTA로 300초 동안 열처리 한 결과 밀집된 구조를 가지는 압전 후막을 제작 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.255-255
• /
• 2016

Resistive random access memory (ReRAM)는 낮은 동작 전압, 빠른 동작 속도, 고집적화 등의 장점으로 인해 차세대 비휘발성 메모리 소자로써 많은 관심을 받고 있다. 최근에 ReRAM 절연막으로 NiOx, TiOx, AlOx TaOx, HfOx와 같은 binary metal oxide 물질들을 적용하는 연구가 활발히 진행되고 있다. 특히, HfOx는 안정적인 동작 특성을 나타낸다는 점에서 ReRAM 절연막 물질로 적합하다고 보고되고 있다. ReRAM 절연막을 형성할 때, 물리 기상 증착 방법 (PVD)이나 화학 기상 증착법 (CVD)과 같은 방법이 많이 이용된다. 이러한 증착 방법들은 고품질의 박막을 형성시킬 수 있는 장점이 있다. 하지만, 높은 온도에서의 공정과 고가의 진공 장비가 이용되기 때문에 경제적인 문제가 있으며, 기판 또는 금속에 플라즈마 손상으로 인한 문제가 발생할 수 있다. 따라서 이러한 문제점들을 개선하기 위해 용액 공정이 많은 관심을 받고 있다. 용액 공정은 공정과정이 간단할 뿐만 아니라 소자의 대면적화가 가능하고 공정온도가 낮으며 고가의 진공장비가 필요하지 않은 장점을 가진다. 따라서 본 연구에서는, 용액공정을 이용하여 HfOx 기반의 ReRAM 제작하였고 $25^{\circ}C$와 $85^{\circ}C$에서 ReRAM의 동작특성에 미치는 compliance current의 영향을 평가하였다. 실험 방법으로는, hafnium chloride (0.1 M)를 2-methoxyethanol에 충분히 용해시켜서 precursor를 제작하였다. 이후, p-type Si 기판 위에 습식산화를 통하여 300 nm 두께의 SiO2 절연층을 성장시킨 후, 하부전극을 형성하기 위해 electron beam evaporation을 이용하여 10/100 nm 두께의 Ti/Pt 전극을 증착하였다. 순차적으로, 제작된 산화물 precursor를 이용하여 Pt 위에 spin coating 방법으로 1000 rpm 10 초, 6000 rpm 30초의 조건으로 두께 35 nm의 HfOx 막을 증착하였다. 최종적으로, solvent 및 불순물을 제거하기 위해 $180^{\circ}C$의 온도에서 10 분 동안 열처리를 진행하였으며, 상부 전극을 형성하기 위해 electron beam evaporation을 이용하여 Ti와 Al을 각각 50 nm, 100 nm의 두께로 증착하였다. ReRAM 동작에서 compliance current가 미치는 영향을 평가하기 위하여 compliance current를 10mA에서 1mA까지 변화시키면서 측정한 결과, $25^{\circ}C$에서는 compliance current의 크기와 상관없이 일정한 메모리 윈도우와 우수한 endurance 특성을 얻는 것을 확인하였다. 한편, $85^{\circ}C$의 고온에서 측정한 경우에는 1mA의 compliance current를 적용하였을 때, $25^{\circ}C$에서 측정된 메모리 윈도우 크기를 비슷하게 유지하면서 더 우수한 endurance 특성을 얻는 것을 확인하였다. 결과적으로, 용액공정 방법으로 제작된 ReRAM을 측정하는데 있어서 compliance current를 줄이면 보다 우수한 endurance 특성을 얻을 수 있으며, ReRAM 소자의 전력소비감소에 효과적이라고 기대된다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.5
• /
• pp.22-31
• /
• 1997

We have measured the optical properties, thickness, and energy band gap of the P $b_{1-x}$/100/L $a_{x}$100/ $Ti_{1-}$0.25x/100/ $O_{3}$ (PLT(x)) thin film prepared by the sol-gel method with varying the La concentration, x, fyom 15 nto 33 mol%. We have obtained the values from the tranmission spectrum and employed the envelope method in anayzing the spectrum. We have also performed the simulation of the transmission spectrum on the PC (personal computer) to verify the accuracy of the values 15 to 33mol%, the refractive index (at .lambda.=632.8nm) increases from 2.39 to 2.44. The extinction coefficient does not depend on the la concentration but mainly on te wavelength, and has the values between 0.2 and 0.5 at the wavelength shorter than 330nm and between 0.001 and 0.008 at the wavelength longer than 700nm. The energy band gap of the PLT (x) thin film has been obtained on the assumption of the direct band-to-band transition. It decreases from 3.28 to 3.17eV as the La concentration increases from 15 to 33 mol%. The thickness of the PLT(x) thin film has been also obtained in high accuracy by the envelope method..

• Corrosion Science and Technology
• /
• v.22 no.5
• /
• pp.359-367
• /
• 2023

The localized corrosion resistance of the Ni-based Inconel 718 alloy after solution heat treatment was evaluated using electrochemical techniques in a solution of 25 wt% NaCl and 0.5 wt% acetic acid. Solution heat treatment at 1050 ℃ for 2.5 hours resulted in an increased average grain diameter. Both Ti carbides (10 ㎛ diameter) and Nb-Mo carbides (1 - 9 ㎛ diameter) were distributed throughout the material. Despite heat treatment, the shape and composition of these carbides remained consistent. An increase in solution temperature led to a decrease in pitting potential value. However, the pitting potential value of solution heat-treated Inconel 718 was consistently higher than that of as-received Inconel 718 at all tested temperatures. Localized corrosion initiation occurred at 0.4 V_SSE in a temperature environment of 80 ℃ for both as-received and solution heat-treated Inconel 718 alloys. X-ray photoelectron spectroscopic analysis indicated that the composition of the passive film formed on specimen surfaces remained largely unchanged after solution heat treatment, with O1s, Cr2p_3/2, Fe2p_3/2, and Ni2p_3/2 present. The difference in localized corrosion resistance between as-received and solution heat-treated Inconel 718 alloys was attributable to microstructural changes induced by the heat treatment process.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.10
• /
• pp.3730-3734
• /
• 2011

The degree of self-assembly and the size variation of nanotubular structures in anodic titanium oxide prepared by the anodization of titanium in ethylene glycol containing 0.25 wt % $NH_4F$ at 40 V were investigated as a function of anodization time. We found that the degree of self-assembly and the size of the nanotubes were strongly dependent on thickness deviation and thus indirectly on anodization time, as the thickness deviation was caused by the dissolution of the topmost tubular structures at local areas during long anodization. A large deviation in thickness led to a large deviation in the size and number of nanotubes per unit area. The dissolution primarily occurred at the bottoms of the nanotubes ($D_{bottom}$) in the initial stage of anodization (up to 6 h), which led to the growth of nanotubes. Dissolution at the tops ($D_{top}$) was accompanied by $D_{bottom}$ after the formed structures contacted the electrolyte after 12 h, generating the thickness deviation. After extremely long anodization (here, 70 h), $D_{top}$ was the dominant mode due to increase in pH, meaning that there was insufficient driving force to overcome the size distribution of nanotubes at the bottom. Thus, the nanotube array became disorder in this regime.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.4
• /
• pp.410-415
• /
• 1997

To investigate the flowering and pod setting characteristics of peanut, Dae-kwangtangkong and Shinnamkwangtangkong were planted on April 20 and May 10 in 1994 at National Honam Agricultural Experiment Station. Number of days from planting to the maximum flowering in Daekwangtangkong were shorter than those of Shinnamkwangtangkong by 6 days in April 20 planting and by 13 days in May 10 planting. Flowering durations of Daekwangtangkong and Shinnamkwangtangkong in April 10 planting were 73 and 71 days, respectively, while those of both varieties were 64 days in May 10 planting. The rates of matured pods on cotyledonary, primary or secondary, and third branches were 58∼78, 6∼15 and 0∼2％, respectively. The rates of effective flowers in Daekwantangkong and Shinnamkwangtangkong were 10％ and 8％, respectively, in April 20 planting. The rates of matured pods were 100％ in Daekwangtangkong and 97％ in Shinnamkwangtangkong when pods were set within 15 days after the initial flowering, while the rate was decreased markedly when pods were set later than 35 days after the initial flowering.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.2
• /
• pp.260-267
• /
• 1995

In temperate zone planting rice at different date subjects the Crop to different climatic condition. The present study aimed at comparison of the change in source-sink relationship of the Japonica(J) and that of IndicaxJaponica(I$\times$J) type rice cultivars caused by shift of heading date. Two J- and two I$\times$J-type cultivars were made to head on August 16, August 26, and September 5. Sink capacity was changed by shift of heading date in different mode between the types of cultivars. In both types major determinant of sink capacity was number of effective tillers, and the number of spikelets per panicle was the minor. In J-type earlier planting/heading was beneficial to increased panicle numbers and this was due mainly to a larger diurnal difference in temperature. I$\times$J-type cultivars favored a higher daily mean temperature to increase the sink capacity. The ability of source at heading, in terms of leaf area per panicle, chlorophyll content per spiklet, photosynthetic ability of leaves per unit area at 25$\^{\circ}C$, carbohydrate and N contents of leaves, was not so different among different heading dates in both types. However, the source activity was governed principally by temperature during grain filling. The J-type cultivars headed on Sept. 5 and I$\times$J-type cultivars headed later than August 16 could not have had sufficient source activity in grain filling due to lower temperature.