• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.3
• /
• pp.53-62
• /
• 1986

For the research on the fatigue fracture behavior in the welded joints of steel structures, base metal specimens and welded ones were selected, and the direct fatigue tests were carried out. Thereafter, fatigue-life (S-N) curves, plastic strain-number of cycles (${\varepsilon}_p$-N) curve, the extrapolated fatigue-life (${\varepsilon}_p$-$N_c$) curve, and da/dN-${\Delta}K$ curves were plotted. By these results the followings were obtained. It was shown that the ratio of fatigue strength at $2{\times}10^6$ cycles of the welded specimen to that of the base metal one was 0.6, and that 0.72 for the base metal and 0.65 for the welded one were the ratio of fatigue strength at $2{\times}10^6$ cycles to yielding stress. The S-N curve for the welded specimen was separated into two sections, the low gradient section and the steep section. As this result, it was shown that the more stress became to reduce, the more the reduction of fatigue strength became to be great. It was shown that fatigue strength at $2{\times}10^6$ cycles from this case was about 83 % of that from the S-N curve plotted with one section. It was thought that the reason was that weld flaw acted greatly on the fatigue strength within the low stress range. It was shown that at the instart of crack initiation plastic strain increased abrupt1y in the case of the welded specimen more than the case of the base metal specimen, and increased abruptly in the upper stress range in both cases. It was shown that the experimental constant ${\alpha}$, 0.42, in the base metal nearly accorded with Manson-Coffin's result, but this made a great difference with the case in the welded specimen. It was thought that it was due to the abrupt change of plastic strain and the influence of weld flaw.

• Transactions of Materials Processing
• /
• v.17 no.4
• /
• pp.249-256
• /
• 2008

Combined phase transformation and heat transfer was considered on the simulation of hot press forming process, using material properties modeler, $JMatPro^{(R)}$ and a finite element package, $DEFORM^{TM}$-HT. In order to obtain high temperature mechanical properties and flow curves for different phases, a material properties modeler, $JMatPro^{(R)}$ was used, avoiding expensive and extensive high temperature materials tests. The results successfully show that the strength of hot press forming parts may exhibit different strength in the same parts, depending on the contact of blank with tooling. It was also shown effectively that the strength of the parts can be controlled by designing appropriate cooling paths and coolants. This was shown in terms of different heat convection coefficient in the calculation. Overall, current combination of software was shown to be an effective tool for the tool and process design of hot forming process, although the material modeler needs to be additionally verified by an appropriate set of high temperature materials test.

• Proceedings of the SCSK Conference
• /
• 2003.09b
• /
• pp.527-527
• /
• 2003

A high-performance liquid chromatographic method for the simultaneous quantitative analysis of DMDM hydantoin, sorbic acid, phenoxy ethanol in cosmetics was studied by using a X-terra C$\sub$18/ column and 0.75mM KH$_2$PO$_4$ in 0.85% sulfuric acid and methanol mixture(7:3) at 214nm. Calibration curves were found to be linear in the 20-100 $\mu\textrm{g}$/mL range (DMDM hydantoin), 50-250 $\mu\textrm{g}$/mL range (sorbic acid) and 10-50 $\mu\textrm{g}$/mL range (phenoxy ethanol). The result of recovery test were 96.6% ∼ 104.2%. This HPLC method can be applied quality control of cosmetics.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1274-1276
• /
• 1993

The silicon-nitride films formed by laser CVD method are used for passivating GaAs surfaces. The electrical Properties of metal-insulator-GaAs structure are studied to determined the interfacial characteristics by C-V curves and deep level transient spectroscopy(DLTS). The SiN films are photolysisly deposited from $SiH_4\;and\;NH_3$ in the range of $100^{\circ}C-300^{\circ}C$ on P type, (100) GaAs. The hysteresis is reduced and interface trap density is lowered to $10^{12}-10^{13}$ at $100^{\circ}C-200^{\circ}C$. The surface leakage current is studied too. The passivated GaAs have a little leakage current compared to non passivated GaAs.

• Transactions of Materials Processing
• /
• v.24 no.4
• /
• pp.264-271
• /
• 2015

In the current study, a method was proposed to quantitatively predict the wear and fatigue life of a shearing die in order to determine an effective replacement period for the die. The shearing die model of a retainer manufacturing process was used for the proposed method of quantitative life prediction. The retainer is produced through shearing steps, such as piercing and notching. The shearing die of the retainer is carefully controlled because the dimensional accuracy of the retainer is critical. The fatigue life for the shearing die was predicted using ANSYS considering S-N curves of STD11 and Gerber’s equation. The wear life for the shearing die was predicted using DEFORM-3D considering the Archard’s wear model. Experimental shearing of the retainer was conducted to verify the effectiveness of the proposed method for predicting die life. The fatigue failure of the shearing die was macroscopically measured. The wear depth was measured using a 3D coordinate measuring machine. The results showed that the wear and fatigue life in the FE analysis agree well with the experimental results.

• Transactions of Materials Processing
• /
• v.23 no.6
• /
• pp.357-362
• /
• 2014

The purpose of the current study is to predict the hardness distribution in steel products after hot stamping using a quench factor analysis(QFA) coupled with FE-simulations. QFA is a method to predict properties such as hardness and tensile strength based on time-temperature-property(TTP) curves and can determine properties based on the temperature histories. The constants($K_1{\sim}K_5$) of QFA were determined using hardness data obtained after various cooling rates. In the current study, a rear side member was selected for evaluation and FE-simulations were performed to obtain the temperature histories during hot stamping. The predicted temperature data were imported into the QFA to calculate the hardness distribution of the hot stamped parts. A hot stamping experiment of the rear side member was conducted to verify the predicted hardness. The simulation results show good agreement with the experimental measurements.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.964-968
• /
• 2010

Ground anchor, commonly referred to as tiebacks or tie-down, is essentially steel elements secured in the ground by cement grout. They are used to provide either lateral or vertical support for various engineered structures, and are effective in all types of soil and rock. However, ground anchor can not be used in soft clay because anchor resistance would not be guaranteed. In this paper, conceptual introduction of the Smart Anchor is presented. The Smart Anchor is a kind of friction type anchor, the load is diffused and applied to the various parts of the distributed bond length, having less impact on the grout strength, and being able to secure necessary anchoring force in relatively soft grounds. This study shows a numerical study of predicting the load transfer of The Smart Anchor in soft clay. A beam-column analysis was performed by a elastic-plastic P-y curves in soft clay.

• Earthquakes and Structures
• /
• v.9 no.2
• /
• pp.415-430
• /
• 2015

Integral abutment bridges have many advantages over bridges with expansion joints in terms of economy and maintenance costs. However, in the design of abutments of integral bridges temperature loads play a crucial role. In addition, seismic loads are readily transferred to the substructure and affect the design of these components significantly. Currently, the European and American bridge design codes consider these two load cases separately in their recommended design load combinations. In this paper, the importance and necessity of combining the thermal and seismic loads is investigated for integral bridges. A 2D finite element combined pile-soil-structure interactive model is used in this evaluation. Nonlinear behavior is assumed for near field soil behind the abutments. The soil around the piles is modeled by nonlinear springs based on p-y curves. The uniform temperature changes occurring at the time of some significant earthquakes around the world are gathered and applied simultaneously with the corresponding earthquake time history ground motions. By comparing the results of these analyses to prescribed AASHTO LRFD load combinations it is observed that pile forces and abutment stresses are affected by this new load combination. This effect is more severe for contraction mode which is caused by negative uniform temperature changes.

• The Korean Journal of Nuclear Medicine
• /
• v.34 no.1
• /
• pp.74-81
• /
• 2000

Purpose: The purpose of this study was to develop in vivo dosimetries using both chromosomal aberrations and micronuclei in mice to assess biological effects of radiations. Materials and Methods: Five each mice were irradiated with 0, 1, 2, 3, 4, 5, 10 Gy of Cs-137 gamma-rays. We scored numbers of chromosomal aberrations in metaphase spreads and numbers of micronuclei in bone marrow smears under light microscope, and obtained the dose-response relationships. We also examined the relationship between the two dose-response curves. Results: The frequency of both chromosomal aberrations and micronuclei increased with dose, in a linear-quadratic manner The delta, beta, and alpha coefficients were 0.0176, 0.0324, and 0.0567 for metaphase analysis (r=1.0, p<0.001) and 0.0019, 0.0073, and 0.0506 for micronuclei assay (r=1.0, p<0.001). The frequency of chromosomal aberrations and micronuclei in different radiation doses was significantly correlated (r=0.99, p<0.01). Conclusion: In vivo dosimetry using either metaphase analysis or micronucleus assay was feasible in mice. These methods could be useful to evaluate biological effects of radiation.

• Biomolecules & Therapeutics
• /
• v.5 no.3
• /
• pp.284-291
• /
• 1997

The pharmacokinetics and tissue distribution of DWP20367 (1-cyclopropyl-6-fluoro-8-chloro-7-(2, 7-diazabicyclo[3,3,0]tract-4-ene-7-yl)-1,4-dihydro-4-oxoquinoline-3-carboxylic acid), a novel fluoroquinolone, were examined in rats and beagle dogs after a single intravenous and oral administration. Analysis of DWP20367 in plasma, tissue, and urine was determined by both HPLC and microbiological assay (bioassay). The plasma concentration-time curves of the drug in rats and beagle dogs were biexponentially declined. The terminal half-life (t$_{1}$2$\beta$/) of the drug in rats was about 60.1 $\pm$7.3 min (i.v.) and 61.3 $\pm$ 12.4 min (p.o.) in bioassay, and 86.3 $\pm$19.8 min (i.v.) and 50.9$\pm$ 14.9 min (p.o.) in HPLC. In beagle dogs, half-life of the drug determined by bioassay was about 121.8$\pm$6.2 min (i.v.) and 111.0$\pm$7.6 min (p.o.). The volume of distribution at steady-state (Vd$_{ss}$ ) was 243.8$\pm$74.1 ml/kg (bioassay) and 339.2$\pm$84.3 ml/kg (HPLC) in rats, and 1587.5 $\pm$536.9 ml/kg (bioassay) in beagle dogs. The total body clearance (Cl$_{t}$) of DWP20367 was 3.4 $\pm$ 0.4 ml/min/kg (bioassay) and 2.4$\pm$0.4 ml/min/kg (HPLC) in rats, and 12.3$\pm$ 1.0 ml/min/kg (bioassay) in beagle dogs, respectively. The extent of bioavailability after oral administration was 89.1%(bioassay) and 79.9% (HPLC) in rats, and 78.7% (bioassay) in beagle dogs. Urinary recovery (24-h) assayed by bioassay was 0.7% (p.o.) and 1.2% (i.v.) in rats, and 0.8% (p.o.) and 1.0% (i.v.) in beagle dogs. In rats, 24-h fecal recovery determined by bioassay was 11.2% (p.o.) and 0.1% (i.v.). Rat and human serum protein binding ratios at 2$\mu$g/ml were about 90~91%. This drug determined by bioassay was also distributed by the order of liver, kidney, lung, heart, spleen and muscle 30 min after oral administration.on.