• Journal of Surface Science and Engineering
• /
• v.26 no.5
• /
• pp.263-270
• /
• 1993

The effects of surfactants on electorless copper plating bath for PCB was studied. Basic bath composition was cuplic sulfate 10g/l, EDTA.2Na 40 g/l, formalin$ 3m\ell$/l and sodium hydroxide solution for pH adjust. After addition of accelerators, stabilizers and surfactants, the polarization curves in plating bath were carried out for presumption of the plating rate. From the plating rate in bath with the various concentration of additives, the optimum condition for manufacturing the electroless copper plating bath was confirmed. It was found that the addition of $\alpha$.$\alpha$'-dipyridyl, pyridine and polyxyethylene octylphenylether was good as stabilizer, accelerator and surfactants, respectively. With this additives, the maximum plating rate of $12\mu\textrm{m}$/h at $65^{\circ}C$ and $2\mu\textrm{m}$/h at $25^{\circ}C$ was obtained.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.3
• /
• pp.210-215
• /
• 2016

The transient characteristics of the Mg/Air fuel cell were ascribed to the load current, electrolyte concentrations, air electrode area and electrode distance. It was found that transient phenomena occurred in the load current, which is due to activate of the oxidation and reduction reaction process. The transient time increase with the load current increase. The transient characteristics were investigated with regard to internal resistance. The maximum power output analysis was employed in order to explain the delayed action under various experimental conditions. The internal resistances had a significant effect on the transient characteristics. The transient curves thus obtained were in almost agreement with internal resistance characteristics.

• Proceedings of the KIEE Conference
• /
• 2004.11b
• /
• pp.158-161
• /
• 2004

This paper presents practical applications of reactive power and voltage planning to obtain voltage stability and operational voltage level for 2005 year summer peak Korea power system. It also describes the new electric facilities, operation criteria, voltage levels, MVAr flows, reactive power reserves in each control area. And reactive compensation devices are installed to maintain established voltage levels and stability margins. This simulation results show the improvement of voltage levels and the increase of reactive margins & interface flow margins. Finally, the paper reports the necessity of dynamic reactive reserves. It can be applied to analysis reactive compensation requirements and P-V & V-Q curves by PSS/E & VSAT.

• Nuclear Engineering and Technology
• /
• v.30 no.6
• /
• pp.555-567
• /
• 1998

Alloy 600 and 690 steam generator tubes fabricated in Korea were evaluated by flare tests according to ASTM standards. The stress acting in the tube elements during the tests was predicted. All the tubes, including alleys 600 and 690, satisfied the requirement of a 30% or 35% O.D expansion. Flow curves obtained from the flare test were found to be higher in alloy 690 tubes than in alloy 600 ones. The difference between alloy 600 and 690 tubes increased gradually with flaring percentage (F.P,%). An effective stress corresponding to mean yield stress was introduced and calculated. It showed that the prediction values were in good agreement with the measured ones for all the 690 and 600 alloy tubes. It became possible to predict the amount of acting stresses within tubes during expansion process.

• Journal of Korean Society of Transportation
• /
• v.19 no.6
• /
• pp.119-129
• /
• 2001

본 연구는 국내의 화물차(이하 트럭) 특성, 도로 조건과 주행 저항이 고려된 트럭 성능 곡선 산출식의 매개변수를 추정하기 위하여 수행되었다. 이를 위해 국내 대표트럭을 선정하고 경사지 진입속도를 산출하였다. 국내 대표트럭의 선정은 자동차 등록현황 자료를 토대로 하여 트럭 중량/마력비에 대한 누적 분포를 작성하고 이 중에서 주요 차종(적재 중량 11톤 이상)의 총중량은 과적 검문소 자료로 보정하여 이루어졌다. 경사지 진입속도는 도별 평지부 직선 구간을 한 곳씩 선정하여 4차로도로와 2차로도로에서 수집되는 자료를 분석하여 산출하였다. 트럭 성능 곡선 산출식을 정립하기 위해 오르막 한계속도$(V_x)$ 산출식을 정리한 뒤 총중량(W), 엔진성능(P), 경사도(G)는 독려 변수로 k, $f_{rc}$, $f_{rv}$, $\Phi$는 매개변수로 설정하였다. 현장조사를 통해서 오르막 한계속도에 도달한 트럭의 총중량과 엔진성능, 속도, 경사도 등의 자료를 수집하여 매개변수 산출에 이용하였다. 마지막으로 추정된 매개변수를 이용하여 트럭 성능 곡선을 도출하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.295-298
• /
• 2005

A minimum commitment method (MCM) was applied to predict the creep rupture life of type 316LN SS. For this purpose, a number of the creep rupture data for the type 316LN SS were collected through literature survey and experimental data of KAERl, Using the short-term creep rupture data under 2000 hr, the long-term creep rupture life above $10^5$ hour was predicted by means of the MCM. An optimum value of A, P and G function, used in the MCM equation, was determined respectively, and the creep rupture life with the A values in different temperatures was compared with the experimental data and the predicted curves.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1179-1185
• /
• 2011

Cold and hot-rolled carbon steel sheets are commonly used in railroad cars or commercial vehicles such as the automobile. The sheets used in these applications are mainly fabricated by spot welding, which is a type of electric resistance welding. However, the fatigue strength of a spot-welded joint is lower than that of the base metal because of high stress concentration at the nugget edge of the spot-welded part. In particular, the fatigue strength of the joint is influenced by not only geometrical and mechanical factors but also the welding conditions for the spot-welded joint. Therefore, there is a need for establishing a reasonable criterion for a long-life design for spot-welded structures. In this thesis, ${\Delta}P-N_f$ relation curves have been used to determine a long-life fatigue-design criterion for thin-sheet structures. However, as these curves vary under the influence of welding conditions, mechanical conditions, geometrical factors, etc. It is very difficult to systematically determine a fatigue-design criterion on the basis of these curves. Therefore, in order to eliminate such problems, the welding residual stresses generated during welding and the stress distributions around the weld generated by external forces were numerically and experimentally analyzed on the basis of the results, reassessed fatigue strength of gas welded joints.

• The Journal of Korean Society for Radiation Therapy
• /
• v.12 no.1
• /
• pp.91-104
• /
• 2000

Recently linear accelerator in radiation therapy in asymmetric field has been easily used since the improvement and capability of asymmetrical field adjustment attached to the machine. It has been thought there have been some significant errors in dose calculation when asymmetrical radiation fields have been utilized in practice of radiation treatments if the fundamental data for dose calculation have been measured in symmetrical standard fields. This study investigated how much the measured data of dose distributions and their isodose curves are different between in asymmetrical and symmetrical standard fields, and how much there difference affect the error in dose calculation in conventional method measured in symmetrical standard field. The distributions of radiation dose were measured by photon diode detector in the water phantom (RFA-300P, Scanditronix, Sweden) as tissue equivalent material on utilization of 6 MV linear accelerator with source surface distance (SSD) 1000 mm. The photon diode detector has the velocity of 1 mm per second from water surface to 250 mm depth in the field size of $40mm{\times}40mm\;to\;250mm{\times}250mm\;symmetric\;field\;and\;40mm{\times}20mm\;to\;250mm{\times}125mm$ asymmetrical fields. The measurements of percent depth dose (PDD) and subsequent plotting of their isodose curves were performed from water surface to 250mm dmm from Y-center axis in $100mm{\times}50mm$ field in order to absence the variability of depth dose according to increasing field sizes and their affects to plotted isodose curves. The difference of PDD between symmetric and asymmetric field was maximum $4.1\%\;decrease\;in\;40mm{\times}20mm\;field,\;maximum\;6.6\%\;decrease\;in\;100mm{\times}50mm\;and\;maximum\;10.2\%\;decrease\;200mm{\times}100mm$, the larger decrease difference of PDD as the greater field size and as greater the depth, The difference of PDD between asymmetrical field and equivalent square field showed maximum $2.4\%\;decrease\;in\;60mm{\times}30mm\;field,\;maximum\;4.8\%\;decrease\;in\;150mm{\times}75mm\;and\;maximum\;6.1\%\;decrease\;in\;250mm{\times}125mm$, and the larger decreased differenced PDD as the greater field size and as greater the depth, these differences of PDD were out of $5\%$ of dose calculation as defined by international Commission on radiation unit and Measurements(ICRU). In the dose distribution of asymmetrical field (half beam) the plotted isodose curves were observed to have deviations by decreased PDD as greater as the blocking of the beam moved closer to the central axis, and as the asymmetrical field increased by moving the block 10 mm keeping away from the central axis, the PDD increased and plotted isodose curves were gradually more flattened, due to reduced amount of the primary beam and the fraction of low energy soft radiations by passing thougepth in asymmetrical field by moving independent jaw each 10 h beam flattening filter. As asymmetrical radiation field as half beam radiation technique is used, the radiation dosimetry calculated in utilizing the fundamental data which measured in standard symmetrical field should be converted on bases of nearly measured data in asymmetrical field, measured beam data flies of various asymmetrical field in various energy and be necessary in each institution.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.5
• /
• pp.559-565
• /
• 2003

An analytical method the determination of benzo(a)pyrene (BaP) and its hydroxylated metabolites, 1-hydroxybenzo(a)pyrene (1-OHBaP), 3-hydroxybenzo(a)pyrene (3-OHBaP), benzo(a)pyrene-4,5-dihydrodiol (4,5-diolBaP) and benzo(a)pyrene-7,8-dihydrodiol (7,8-diolBaP), in rat urine and plasma has been developed by HPLC/FLD and GC/MS. The derivatization with alkyl iodide was employed to improve the resolution and the detection of two mono hydroxylated metabolites, 1-OHBaP and 3-OHBaP, in LC and GC. BaP and its four metabolites in spiked urine were successfully separated by gradient elution on reverse phase ODS $C_{18}$ column (4.6 mm I.D., 100 mm length, particle size 5 ㎛) using a binary mixture of MeOH/H₂O (85/15, v/v) as mobile phase after ethylation at 90 ℃ for 10 min. The extraction recoveries of BaP and its metabolites in spiked samples with liquid-liquid extraction, which was better than solid phase extraction, were in the range of 90.3- 101.6% in n-hexane for urine and 95.7-106.3% in acetone for plasma, respectively. The calibration curves has shown good linearity with the correlation coefficients (R²) varying from 0.992 to 1.000 for urine and from 0.996 to 1.000 for plasma, respectively. The detection limits of all analytes were obtained in the range of 0.01-0.1 ng/mL for urine and 0.1-0.4 ng/mL for plasma, respectively. The metabolites of BaP were excreted as mono hydroxy and dihydrodiol forms after intraperitoneal injection of 20 mg/kg of BaP to rats. The total amounts of BaP and four metabolites excreted in dosed rat urine were 3.79 ng over the 0-96 hr period from adminstration and the excretional recovery was less than 0.065% of the injection amounts of BaP. The proposed method was successfully applied to the determination of BaP and its hydroxylated metabolites in rat urine and plasma for the pharmacokinetic studies.

• Nutrition Research and Practice
• /
• v.14 no.6
• /
• pp.679-690
• /
• 2020

BACKGROUND/OBJECTIVES: Concerns about regional disparities in heathy eating and nutritional status among South Korean adults are increasing. This study aims to identify the magnitude of regional disparities in diet and nutritional status among Korean adults who completed the 2017 Korea National Health and Nutrition Examination Survey (KNHANES). SUBJECTS/METHODS: The participants were a nationally representative sample of Korean adults aged 19 years and older from the 2017 KNHANES (n = 6,126). We employed the svy commands in STATA to accommodate the complex survey design. The relative concentration index (RCI), absolute concentration index (ACI) and index of disparity were used to measure regional nutritional inequalities. RESULTS: Overweight and obese adults were more prevalent among the poor than among the rich in urban areas (RCI = -0.041; P < 0.05), while overweight and obese adults were more prevalent among the rich than among the poor in rural areas of South Korea (RCI = 0.084; P < 0.05). Economic inequality in fruit and vegetable intake ≥ 500 g per day was greater in rural areas than in urban areas in both relative size (RCI = 0.228 vs. 0.091, difference in equality = 0.137; P < 0.05) and absolute size (ACI = 0.055 vs. 0.023, difference in equality = 0.032; P < 0.05). CONCLUSIONS: This study provides useful information identifying opposite directions in the relative concentration curves between urban and rural areas. Adult overweight/obesity was more prevalent among the poor in urban areas, while adult overweight/obesity was more prevalent among the rich in rural areas. Public health nutrition systems should be implemented to identify nutritional inequalities that should be targeted across regions in South Korea.