• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.757-760
• /
• 2009

최근 들어 WGS 반응은 Pt과 같은 귀금속 촉매를 다양한 담체에 담지하여 낮은 온도에서 높은 활성을 지닌 촉매를 제조하기 위한 연구가 활발히 진행되고 있다. WGS 반응에서 귀금속 촉매가 높은 활성을 가지기 위해서 높은 산소저장능력(Oxygen Storage Capacity)과 산화환원능력(Redox)을 지닌 담체 개발이 필요하다. Ce-$ZrO_2$ 담체는 구조적으로 안정하며 높은 산소저장능을 가지고 있는 것으로 알려져 있다. Ce-$ZrO_2$ 구조는 Ce/Zr 비에 따라 다양한 변화가 생긴다. Ce/Zr 비가 6/4, 8/2인 경우 입방구조(Cubic)를 가지며 2/8인 경우 정방입계(Tetragonal)구조를 가진다. 이것은 담체 특성의 변화를 의미한다. 따라서, WGS 반응용 최적 담체를 선정하기 위해 Ce/Zr 비를 제조변수로 하여 담체특성을 분석하였다. 제조된 모든 담체는 공침법(Co-precipitation)을 사용하여 제조하였으며 $500^{\circ}C$에서 6시간 소성하였다. 담체 특성분석은 BET, XRD를 이용하였다. 추가적으로 제조변수를 다양화하여 담체 제조를 마쳤으며 특성분석이 진행 중이다. 분석 결과 $Ce_{0.2}Zr_{0.8}O_2$ 담체가 가장 넓은 표면적을 가지고 있으며 Ce/Zr 비가 높아질수록 표면적이 감소하는 경향을 나타내었다. Ce-$ZrO_2$ 담체의 나노결정크기는 Ce/Zr 비가 작아질수록 결정크기가 감소하는 경향을 나타내었으며 $Ce_{0.2}Zr_{0.8}O_2$가 Ce-$ZrO_2$ 담체 중에서 가장 작은 결정크기를 나타내어 3nm 이하의 나노-담체가 제조되었음을 확인하였다.

• Journal of Surface Science and Engineering
• /
• v.46 no.4
• /
• pp.139-144
• /
• 2013

c-BN(cubic boron nitride) is known to have extremely high hardness next to diamond, as well as very high thermal and chemical stability. The c-BN in the form of film is useful for wear resistant coatings where the application of diamond film is restricted. However, there is less practical application because of difficult control of processing variables for synthesis of c-BN film as well as unclear mechanism on formation of c-BN. Therefore, in the present study, the structural characterization of c-BN thin film were investigated using $B_4C$ target in r.f. magnetron sputtering system as a function of processing variables. c-BN films were coated on Si(100) substrate using $B_4C$ (99.5% purity). The mixture of nitrogen and argon was used for carrier gas. The deposition processing conditions were changed with substrate bias voltage, substrate temperature and base pressure. Fourier transform infrared microscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) were used to analyze crystal structures and chemical binding energy of the films. In the case of the BN film deposited at room temperature, c-BN was formed in the substrate bias voltage range of -400 V~ -600 V. Less c-BN fraction was observed as deposition temperature increased and more c-BN fraction was observed as base pressure increased.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.75.1-75.1
• /
• 2011

Coal gasification is considered as one of the most prospective technologies in energy field since it can be utilized for various products such as electricity, SNG (Synthetic Natural Gas or Substitute Natural Gas) and other chemical products. Among those products from coal gasification, SNG is emerging as a very lucrative product due to the rising prices of oil and natural gas, especially in Asian countries. The process of SNG production is very similar to the conventional IGCC in that the overall process is highly dependent on the type of gasifier and coal rank. However, there are some differences between SNG production and IGCC, which is that SNG plant requires higher oxygen purity from oxygen plant and more complex gas cleanup processes including water-gas shift reaction and methanation. Water-gas shift reaction is one of the main process in SNG plant because it is a starting point for the latter gas cleanup processes. For the methanation process, syngas is required to have a composition of $H_2$/CO = 3. This study reviewed various considerations for water-gas shift process in a conceptual design on an early stage like a feasibility study for a real project. The factors that affect the design parameters of water-gas shift reaction include the coal properties, the type of gasifier, the overall thermal efficiency of the plant and so on. Water-gas shift reaction is a relatively proven technology compared to the other processes in SNG plant so that it can reduce technological variability when designing a SNG project.

• Clean Technology
• /
• v.29 no.4
• /
• pp.321-326
• /
• 2023

Recently, there has been a growing interest in clean hydrogen energy that does not emit carbon dioxide during combustion due to the increasing focus on carbon neutral. Research related to hydrogen production continues, and in this study, we applied waste-derived synthesis gas to the water-gas shift reaction to simultaneously treat waste and produce high-purity hydrogen. To enhance catalytic activity in the high-temperature water-gas shift (HT-WGS) reaction, magnesium was used as a support material alongside cerium. Cu-CeO₂-MgO catalysts were synthesized, with copper acting as the active component for the HT-WGS reaction. A study on the catalytic activity based on the preparation method was conducted, and the Cu-CeO₂-MgO catalyst prepared by impregnation method exhibited the highest activity in the HT-WGS reaction. The observed superior performance of the Cu-CeO₂-MgO catalyst prepared through the impregnation method can be attributed to its significantly higher oxygen storage capacity and amount of active Cu species.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.1-7
• /
• 2018

Tin dioxide, $SnO_2$, is applied as an anode material in Li-ion batteries and a gas sensing materials, which shows changes in resistance in the presence of gas molecules, such as $H_2$, NO, $NO_2$ etc. Considerable research has been done on the synthesis of $SnO_2$ nanostructures. Nanomaterials exhibit a high surface to volume ratio, which means it has an advantage in sensing gas molecules and improving the specific capacity of Li-ion batteries. In this study, $SnO_2$ nanostructures were grown on a Si substrate using a thermal CVD process with the vapor transport method. The carrier gas was mixed with high purity Ar gas and oxygen gas. The crystalline phase of the as-grown tin oxide nanostructures was affected by the oxygen gas flow rate. The crystallographic property of the as-grown tin oxide nanostructures were investigated by Raman spectroscopy and XRD. The morphology of the as-grown tin oxide nanostructures was confirmed by scanning electron microscopy. As a result, the $SnO_2$ nanostructures were grown directly on Si wafers with moderate thickness and a nanodot surface morphology for a carrier gas mixture ratio of Ar gas 1000 SCCM : $O_2$ gas 10 SCCM.

• Economic and Environmental Geology
• /
• v.50 no.4
• /
• pp.287-302
• /
• 2017

The carbonate rocks of the Daegi Formation are composed of the limestone at the upper and lower zones, and the dolomite at the middle zone, in which the upper zone has higher CaO content than others. The colors of carbonate rock in the Daegi Formation can be divided into five types; white, light brown, light gray, gray, and dark gray. The white to light gray colored rocks correspond to the high purity limestone with 53.15 ~ 55.64 wt. % CaO, and the light brown colored rocks contain 20.71 ~ 21.67 wt. % MgO. The bleaching of carbonate rocks are not related to CaO composition of the rocks, as light gray rocks tend to be higher in CaO content than those of the white rocks at the lower zone. The pelitic components are also occasionally increased in white limestone than light grey one. $Al_2O_3$ is one of the most difficult content to remove during hydrothermal processes, so the interpretation that the limestone is purified together with hydrothemral bleaching, has little merit. The wide range (over 16 ‰) of ${\delta}^{18}O_{SMOW}$, smaller variation (within 2 ‰) of ${\delta}^{13}C_{PDB}$ are apparent in both the upper and lower zones, which indicate the Daegi Formation had been affected overall by hydrothermal fluids. The K-Ar isotopic age of hydrothermal alteration in the GMI limestone mine is $85.1{\pm}1.7Ma$. Gradual change from grey through light grey to white limestone is accompaned by lower oxygen stable isotope values, which is major evidence that the hydrothermal effect is the main process of the bleaching. Although the Daegi Formation has suffered from hydrothermal activity and increase in whiteness, there is no clear evidence demonstrating the relationship between bleaching and high purity of limestone. The purification of limestone has nothing to do with the hydrothermal activity in this area. Instead, it should be considered that the change of sedimentary environment related to see-level fluctuation which can prevent deposition of pelitic components especially $Al_2O_3$ contrbuted to the formation of the high purity limestone in the upper zone of the Daegi Formation. Considering the evidences such as increase in CaO content of limestone by depth, gradual change from calcite to dolomite at the lower zones, and occurring the high purity limestone at the upper zone, the interpretation of sequence stratigraphic aspect to the formation of the high purity Daegi limestone appears to be more suitable than that of hydrothermal alteration origin.

• Journal of Life Science
• /
• v.15 no.5 s.72
• /
• pp.772-778
• /
• 2005

Chiral epoxides are important chiral synthons in organic synthesis for the production of chiral pharmaceuticals and functional food additives. Chiral epoxides can be synthesized by enantioselective introduction of oxygen to double bond of substrate by monooxygenase. Peroxidase also carry out asymmetric epoxidation of alkene in the presence of hydrogen peroxide. Kinetic resolution of racemic epoxides via enantioselective hydrolysis reaction by epoxide hydrolase (EH) is a very promising method since chiral epoxides with a high optical purity can be obtained from cheap and readily available racemic epoxides. In this review, various biocatalytic approaches for the production of chiral epoxides with several examples are presented and their commercial potential is discussed.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.239-239
• /
• 2003

As a result of the recent miniaturization and enhancement in the performance of thin film inductors and thin film transformers, there are increased demands for the thin films with a high magnetic permeability in the high frequency range, a high saturation magnetization, a high electrical resistivity, and a low coercive force. In order to improve high frequency properties, we will investigate anisotropy field by shape and size of pattern. The Fe-Al-O thin films of 16mm diameter and 1$\mu\textrm{m}$ thickness were deposited on Si wafer, using RE magnetron reactive sputtering technique with the mixture of argon and oxygen gases. The fabricating conditions are obtained in the working partial pressure of 2m Torr, O$_2$ partial Pressure of 5%, Input power of 400w, and Al pellets on an Fe disk with purity of 99.9%. For continuous thin film is the 4Ms of 19.4kG, H$\sub$c/ of 0.6Oe, H$\sub$k/ of 6.0Oe and effective permeability of 2500 up to 100MHz. In this work, we expect to enhanced effect of magnetic anisotropy on patterned of Fe-Al-O thin films.

• Journal of Powder Materials
• /
• v.21 no.1
• /
• pp.39-43
• /
• 2014

Bulk nanostructured copper was fabricated by a shock compaction method using the planar shock wave generated by a single gas gun system. Nano sized powders, average diameter of 100 nm, were compacted into the capsule and target die, which were designed to eliminate the effect of undesired shock wave, and then impacted with an aluminum alloy target at 400 m/s. Microstructure and mechanical properties of the shock compact specimen were analyzed using an optical microscope (OM), scanning electron microscope (SEM), and micro indentation. Hardness results showed low values (approximately 45~80 Hv) similar or slightly higher than those of conventional coarse grained commercial purity copper. This result indicates the poor quality of bonding between particles. Images from OM and SEM also confirmed that no strong bonding was achieved between them due to the insufficient energy and surface oxygen layer of the powders.

• Journal of Powder Materials
• /
• v.16 no.2
• /
• pp.98-103
• /
• 2009

The ultrafine titanium carbonitride particles ($TiC_{0.7}N_{0.3}$) below 100nm in mean size were successfully synthesized by Mg-thermal reduction process. The nanostructured sub-stoichiometric titanium carbide ($TiC_{0.7}$) particles were produced by the magnesium reduction at 1123K of gaseous $TiC_{l4}+xC_2Cl_4$ and the heat treatments in vacuum were performed for five hours to remove residual magnesium and magnesium chloride mixed with $TiC_{0.7}$. And final $TiC_{0.7}N_{0.3}$ phase was obtained by nitrification under normal $N_2$ gas at 1373K for 2 hrs. The purity of produced $TiC_{0.7}N_{0.3}$ particles was above 99.3% and the oxygen contents below 0.2 wt%. We investigated in particular the effects of the temperatures in vacuum treatment on the particle refinement of final product.