• Wind and Structures
• /
• 제19권4호
• /
• pp.389-404
• /
• 2014

The flow characteristics of a circular cylinder surrounded by an outer permeable cylinder were experimentally investigated using Particle Image Velocimetry Technique in deep water flow. In order to consider the effects of diameter and porosity of the outer cylinder on flow structures of the inner cylinder, five different outer cylinder diameters (D=37.5, 52.5, 60, 75 and 90 mm) and eight different porosities (${\beta}$=0.4, 0.5, 0.6, 0.65, 0.7, 0.75, 0.8 and 0.85) were selected. During the experiments, the diameter of inner cylinder was kept constant as d=30 mm. The depth-averaged free-stream velocity was adjusted as U=0.156 m/s, which corresponds to the Reynolds number of Re=5000 based on the inner cylinder diameter. It has been concluded that both the outer permeable cylinder diameter and the porosity have important influences on the attenuation of vortex shedding in the wake region. The presence of outer permeable cylinder decreases the magnitude of Reynolds shear stress and turbulent kinetic energy compared to the bare cylinder case. Moreover, the spectral analysis of vortex shedding frequency has revealed that the dominant frequency of vortex shedding downstream of the cylinder arrangement also reduces substantially due to the weakened Karman shear layer instability.

• Design & Manufacturing
• /
• 제18권2호
• /
• pp.1-8
• /
• 2024

Unlike the roll-to-roll process that uses a steel roll and a nip roll, a vacuum roll can hold and transfer a thin film using a single roll. To precisely manufacture a vacuum roll, a thin outer cylinder must be machined, which is assembled on the outside of the roll and contacts the film via vacuum pressure. In this study, the effects of jaw width and chucking force on the deformation of the outer cylinder during the turning process were investigated using analysis, and a precision machining and burr removal process was developed. The deformation of the outer cylinder decreased almost linearly with increasing jaw width and increased with higher chucking force and larger cylinder diameter. Additionally, the deflection due to the weight of the outer cylinder was approximately three times greater than that caused by film tension. For the machined outer cylinder, a burr removal experiment was conducted, and concentricity and cylindricity were measured. Using a device that removes burrs by rotating a wheel connected to the main shaft at high speed, it was found that burrs generated on the inner diameter could be removed very efficiently. On the vacuum side, the concentricity errors of the inner and outer diameters were 0.015 mm and 0.014 mm, respectively, and on the opposite side, they were 0.006 mm and 0.010 mm, respectively. Additionally, the measurement of Total Indicator Runout (TIR) according to the angle showed that the maximum cylindricity of the outer and inner diameters was 0.02 mm and 0.025 mm, respectively. Finally, through burr-height measurement at the hole boundary, it was found that the heights were within 0.05 mm.

• 한국응용과학기술학회지
• /
• 제32권4호
• /
• pp.616-622
• /
• 2015

IMO에서 규제중인 선박평형수의 처리기술은 현재 대부분 화학적 처리법 및 전기적인 처리방법을 주로 이용하고 있는데 이러한 방법들은 2차오염의 위험을 가지고 있으며 이를 방지하기 위하여 추가적인 장치가 필요하다. 본 연구에서는 전단력을 활용한 물리적인 방법을 이용하여 2차 오염 없이 선박평형수를 처리하는 방법을 연구하였다. 균일장치의 원리를 이용하여 전단응력으로 균을 파쇄시키는 원리인데, 내부 실린더와 외부 실린더의 표면이 매끄러운 경우에는 미끄럼 현상이 나타나 효율적인 살균효과를 얻기가 어려워서 전단응력의 크기를 변화시키는 다양한 요인 가운데 표면의 모양을 다르게 하여 두 가지 type의 장치에 대한 살균 성능을 비교하였다. 기본 장치는 cylinder type이나, 내부 실린더와 외부 실린더에 일정 간격과 깊이로 홈을 파낸 groove type과 멸균성능을 비교하였다. 그 결과 미끄럼을 방지한 groove type에서 cylinder type보다 우수한 결과를 나타내었다.

• 한국전산유체공학회지
• /
• 제6권3호
• /
• pp.1-9
• /
• 2001

Mixed convection in a horizontal annulus is considered, and the effect of a forced flow on the natural convective flow is investigated. The inner cylinder is hotter than the outer cylinder, and the outer cylinder is rotating with constant angular velocity with its axis at the center of the annulus. The unsteady streamfunction-vorticity equation is solved with a finite difference method. For the fluid with Pr=0.7, there appear flows with two eddies, one eddy, or no eddy according the Rayleigh and Reynolds numbers. The rotation of the outer cylinder reduces the heat transfer rate at the wall of the annulus. The oscillatory multicellular flow of a low Prandtl number fluid with Pr=0.01 can be effectively suppressed by the forced flow.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1999년도 학술발표대회 논문집 제18권 1호
• /
• pp.303-306
• /
• 1999

The paper describes a theoretical study on the speed of the torsional elastic waves propagating in a circular cylinder whose outer radius varies periodically as a harmonic function of the axial coordinate. The approximate solution for the phase speed has been obtained using the perturbation technique for sinusoidal modulation of small amplitude. It is shown that the wave speed in the cylinder with a corrugated outer surface is less than that in a smooth cylinder by the square of the amplitude of the surface perturbation. This theoretical prediction agrees reasonably with an experimental observation reported earlier. It is also shown that the wave speed reduction due to the surface corrugation becomes larger for a thinner cylinder and for a bigger density of corrugation.

• 대한기계학회논문집B
• /
• 제21권4호
• /
• pp.551-561
• /
• 1997

Mixed convection of air in a horizontal concentric cylindrical annulus is investigated numerically. Isothermal boundary conditions are prescribed at the inner and outer cylinders, with the inner cylinder being warmer. The forced flow is induced by the outer cylinder which is rotating slowly with constant angular velocity with its axis at the center of the annulus. The effect of the forced flow on the flow pattern and heat transfer of natural convection is investigated for the annulus of (inner-cylinder radius/gap width) = 1. There appear two eddies, one eddy or no eddy according to the Rayleigh and Reynolds numbers. Map of the three flow regimes is constructed on the Ra-Re plane. (author). 28 refs., 9 figs., 2 tabs.

• 한국가시화정보학회지
• /
• 제6권2호
• /
• pp.33-38
• /
• 2008

The effect of the radial temperature gradient and the presence of slits in the wall of outer of two cylinders involved in creating a Taylor-Couette flow was investigated by measuring the velocity field inside the gap. The slits were azimuthally located along the inner wall of the outer cylinder and the number of slits used in this study was 18. The radius ratio and aspect ratio of the models were 0.825 and 48, respectively. The heating film wrapped around the inner cylinder was used for generating the constant heat flux and we ensured the constant temperature condition at the outer space of the outer cylinder. The velocity fields were measured by using the PIV(particle image velocimetry) method. The refractive index matching method was applied to remove image distortion. The results were compared with plain wall configuration of Taylor-Couette flow. From the results, the presence of slits in the wall of outer cylinder and temperature gradient increased the flow instability.

• 대한기계학회논문집B
• /
• 제20권2호
• /
• pp.689-696
• /
• 1996

A comparison is made of the heat loss from a hollow cylinder, computed using an one-dimensional analytic method and a two-dimensional separation of variables scheme. For a two-dimensional analysis, the temperature of the inner surface as a boundary condition can be varied along the length of the cylinder by varing the temperature variation factor, b. Comparisons of the heat loss from the hollow cylinder using these two methods are given as a function of non-dimensional cylinder length, the ratio of the outer radius to the inner radius, temperature variation factor and Biot number. The result shows that the value of the heat loss from the hollow cylinder obtained using the one-dimensional analytic method becomes close to the value given by the two-dimensional separation of variables scheme as the value of Biot number and the non-dimensional hollow cylinder length increase and as the ratio of the outer radius to the inner radius decreases.

• Korean Chemical Engineering Research
• /
• 제54권5호
• /
• pp.630-635
• /
• 2016

선행연구에서는 2차오염이 없는 물리적 처리방법인 전단응력을 이용한 선박평형수 처리장치에 대하여 연구하였다. 정지상태의 외부 실린더와 회전하는 내부 실린더 사이에 발생하는 전단응력을 이용하여 다양한 미생물을 파쇄 처리하는 원리이며, 전단응력은 실린더 표면의 형태나 회전속도에 따라 크기가 달라진다. 전단응력의 크기와 전단응력을 받는 시간에 따라 멸균정도가 차이를 보이기 때문에, 다양한 조건에 따른 멸균효율을 밝히는 실험이 필요하며 이를 통해 상업용 장치의 제작을 위한 기초 자료를 마련하고자 하였다. 선행연구에서는 disk type과 cylinder type의 비교를 통하여 cylinder type이 우수함을 밝혔다. 본 연구에서는 선행연구를 통하여 얻은 결과를 바탕으로 cylinder type, groove type, knurling type의 표면 조건을 변화시켜 가장 우수한 조합을 밝혀냄과 동시에 실린더 사이의 간격에 따른 회전속도 및 유속 조건을 최적화 하고자하였다. 그 결과 groove type에서 250 mL/min의 유량조건에서는 8000 rpm 이상, 혹은 500 mL/min의 유량조건에서는 10000 rpm 이상에서 100% 살균 처리되는 결과를 얻었다.

• 대한설비공학회지:설비저널
• /
• 제17권4호
• /
• pp.328-335
• /
• 1988

Natural convection in annuli between the horizontal and vertical concentric cylinders for ratio of the inner to the outer radius, $R_1$=0.85, 0.35 has been studied by the numerical analysis. Governing equations are numerically sloved by means of Successive over-relaxation methods. It is found that maximum local Nusselt number, $Nu_{1.max}$ at the inner cylinder and $Nu_{2.max}$ at the outer cylinder for $R_2$=0.35 have maxima at ${\phi}=0^{\circ}$, ${\phi}=180^{\circ}$ ${\xi}=0.4$, 1.6 for horizontal cylinder and at bottom, top for vertical cylinder, respectively. In the present study, mean Nusselt numbers at the vertical cylinder increased more than that at the horizontal cylinder by about 64% for $R_1$=0.35.