• Computers and Concrete
• /
• v.20 no.5
• /
• pp.545-553
• /
• 2017

A pounding tuned mass damper (PTMD) can be considered as a passive device, which combines the merits of a traditional tuned mass damper (TMD) and a collision damper. A recent analytical study by the authors demonstrated that the PTMD base on the energy dissipation during impact is able to achieve better control effectiveness over the traditional TMD. In this paper, a PTMD prototype is manufactured and applied for seismic response reduction to examine its efficacy. A series of shaking table tests is conducted in a three-story building frame model under single-dimensional and two-dimensional broadband earthquake excitations with different excitation intensities. The ability of the PTMD to reduce the structural responses is experimentally investigated. The results show that the traditional TMD is sensitive to input excitations, while the PTMD mostly has improved control performance over the TMD to remarkably reduce both the peak and root-mean-square (RMS) structural responses under single-dimensional earthquake excitation. Unlike the TMD, the PTMD is found to have the merit of maintaining a stable performance when subjected to different earthquake loadings. In addition, it is also indicated that the performance of the PTMD can be enhanced by adjusting the initial gap value, and the control effectiveness improves with the increasing excitation intensity. Under two-dimensional earthquake inputs, the PTMD controls remain outperform the TMD controls; however, the oscillation of the added mass is observed during the test, which may induce torsional vibration modes of the structure, and hence, result in poor control performance especially after a strong earthquake period.

• Journal of KIISE
• /
• v.42 no.8
• /
• pp.1039-1048
• /
• 2015

Recently, the web-based adaptive streaming service, DASH (Dynamic Adaptive Streaming over HTTP), is receiving more attention. However, existing network-based and buffer-based video quality control schemes in DASH environments make oscillation of segment throughput, causing degradation of the quality of experience (QoE) with frequent quality changes and playback interruptions because these schemes do not consider the content characteristics. In this paper, we propose a C-DASH (Content Characteristics based Dynamic Adaptive Streaming over HTTP) scheme in order to improve the QoE in DASH environments. The C-DASH scheme performs seamless and smooth quality control based on the segment throughput, buffer status, and segment size of the content. Based on simulation results, it is confirmed that the C-DASH scheme can improve the QoE, when compared with the existing quality control schemes.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.6
• /
• pp.23-36
• /
• 2005

PLLs have been widely used for many applications including communication systems. This paper presents a VCO with an improved negative skewed delay scheme and a PLL using this VCO. The proposed VCO and PLL are intended for replacing traditional LC oscillators and PLLs used in communication systems and other applications. The circuit designs of the VCO and PLL are based on 0.18um CMOS technology with 1.8V supply voltage. The proposed VCO employs subfeedback loops using pass-transistors and needs two opposite control voltages for the pass transistors. The subfeedback loops speed up oscillation depending on the control voltages and thus provide a high oscillation frequency. The two voltage controls have opposite frequency gain characteristics and result in low phase-noise. The 7-stage VCO in 0.18um CMOS technology operates from $3.2GHz\~6.3GHz$ with phase noise of about -128.8 dBc/Hz at 1MHz frequency onset. For 1.8V supply voltage, the current consumption is about 3.8mA. The proposed PLL has dual loop-filters for the proposed VCO. The PLL is operated at 5GHz with 1.8V supply voltage. These results indicate that the proposed VCO can be used for radio frequency operations replacing LC oscillators. The circuits have been designed and simulated using 0.18um TSMC library.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.28 no.1
• /
• pp.35-48
• /
• 1995

To develop the optimal design method for the longline type scallop culturing facilities in the open sea numerical calculations and hydraulic model experiments are carried out for the stability and function optimization. Using the results for the motion and tension of the facilities, stable design concepts and effects of motion control system by vertical anchor and resistance discs art discussed. The results of this study that can be applied to the design are as follows: 1) Total external forces by design wave $(H_{1/3}\;=\;6,7\;m,\;T_{1/3}\;=\;12sec)$ at the coastal waters of Jumunjin for unit facility (one main line) are estimated to 5-20 tons, and required anchor weights are 10-40 tons in the case of 2-point mooring system. Though the present facilities are stable to steady currents, but is unstable to the extreme wave condition of return period of 10 years. 2) The dimensions and depth of array systems must be designed considering the ecological environments as well as the physical characteristics including the mooring and holding forces that are proportional to the length and relative depth of main line to wave length, and the number of buoys and nets. 3) Oscillation of the facility is influenced by water particle motion and the weight of hanging net, and is excited at both edge, especially at the lee side. To reduce the motion of the nets, the vertical anchoring system and the resistence disc method are recommended by the experimental results, 4) The damage of rope near the anchor by abrasion should be prevented using the ring-type connection parts or anchor chains.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.42-47
• /
• 2002

Measuring magnetic fields with a SQUID sensor always requires preliminary adjustments such as optimum bas current determination and flux-locking point search. A conventional magnetoencephalography (MEG) system consists of several dozens of sensors and we should condition each sensor one by one for an experiment. This timeconsuming job is not only cumbersome but also impractical for the common use in hospital. We had developed a serial port communication protocol between SQUID sensor controllers and a personal computer in order to control the sensors. However, theserial-bus-based control is too slow for adjusting all the sensors with a sufficient accuracy in a reasonable time. In this work, we introduce programmatic control sequence that saves the number of the control pulse arrays. The sequence separates into two stages. The first stage is a function for searching flux-locking points of the sensors and the other stage is for determining the optimum bias current that operates a sensor in a minimum noise level Generally, the optimum bias current for a SQUID sensor depends on the manufactured structure, so that it will not easily change about. Therefore, we can reduce the time for the optimum bias current determination by using the saved values that have been measured once by the second stage sequence. Applying the first stage sequence to a practical use, it has taken about 2-3 minutes to perform the flux-locking for our 37-channel SQUID magnetometer system.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.4
• /
• pp.290-294
• /
• 2014

PID(Proportional, Integral, Derivative) controller is the most popular process controllers in nuclear power plants. The optimized parameter setting of the process controller contributes to the stable operation and the efficiency of the operating nuclear power plants. PID parameter setting is tuned when new process control systems are installed or current process control systems are changed. When the nuclear plant is shut down, a lot of PID tuning methods such as the Trial and Error method, Ultimate Oscillation method operation, Ziegler-Nichols method, frequency method are used to tune the PID values. But inadequate PID parameter setting can be the cause of the unstable process of the operating nuclear power plant. Therefore the results of PID parameter setting should be simulated, optimized and finally verified. This paper introduces the simulation method of PID tuning to optimize the PID parameter setting and confirms them of the actual PID controller in the operating nuclear power plants. The simulation method provides the accurate process modeling and optimized PID parameter setting of the multi-loop control process in particular.

• International Journal of Aeronautical and Space Sciences
• /
• v.13 no.1
• /
• pp.117-125
• /
• 2012

This paper presented the design of SRPS, ground function test, and the deployment test on a high speed taxi of KC-100 airplane. KAI has developed a spin recovery system in collaboration with Airborne Systems for KC-100 general aviation airplane. Spin mode analysis, rotary balance and forced oscillation tests were performed to obtain the rotational, dynamic derivatives in the preliminary design phase. Prior to the detailed design process of SRPS, approximations for initial estimation of design parameters- fineness ratio, parachute porosity, parachute canopy filling time, and deployment method- were considered. They were done based on the analytical disciplines such as aerodynamics, structures, and stability & control. SRPS consists of parachute, tractor rocket assembly for deployment, attach release mechanism (ARM) and cockpit control system. Before the installation of SRPS in KC-100 airplane, all the control functions of this system were demonstrated by using SBTB(System Breakout Test Box) in the laboratory. SBTB was used to confirm if it can detect faults, and simulate the firing of pyrotechnic devices that control the deployment and jettison of SRPS. Once confirmed normal operation of SRPS, deployment and jettison of parachute on the high speed taxiing were performed.

• Journal of KIISE:Information Networking
• /
• v.36 no.6
• /
• pp.492-504
• /
• 2009

The delivery of multimedia that efficiently adapts its bit-rate to changing network characteristics and conditions is one of the important challenging tasks in the design of today's real-time multimedia streaming systems such as IPTV, Mobile IPTV and so on. In these work, the primary focus is on network congestion, to improve network stability and inter-protocol fairness. However, these existing works have problems which do not support QoE (Quality of Experience), because they did not consider essential characteristics of contents playback such as the media continuity. In this paper, we propose a novel rate control scheme for improving the QoE of multimedia streaming service in the Internet congestion, called NCAR (Network and Client-Aware Rate control), which is based on network-aware congestion control and client-aware flow control scheme. Network-aware congestion control of the NCAR offers an improving reliability and fairness of multimedia streaming, and reduces the rate oscillation as well as keeping high link utilization. Client-aware flow control of NCAR offers a removing the media discontinuity and a suitable receiver buffer allocation, and provides a good combination of low playback delay. Simulation results demonstrate the effectiveness of our proposed schemes.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.3
• /
• pp.27-33
• /
• 2009

A computational study has been performed out to evaluate the effect of a vertical porous barrier on the pressure oscillations in a supersonic cavity. The porous barriers with different perforations were vertically installed into a rectangular cavity at Mach numbers 1.50, 1.83 and 2.50. TVD finite difference MUSCL scheme was employed to solve the two-dimensional, unsteady, compressible Navier-Stokes equations. The present vertical porous barrier considerably altered the characteristics of the time-dependent shear layers that occur at the upstream edge of cavity and remarkably reduced the pressure oscillations inside the supersonic cavity. The present results showed that the effectiveness of passive control using the present porous vertical barrier is dependent on Mach number and the perforation of the porous barrier.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.165-170
• /
• 1997

In this paper, we consider the aortic sinus baroreceptor, which is the most representative baroreceptors sensing the variance of pressure in the cardiovascular system(CVS), and propose heart activity control model to observe the effect of delay time in heart period and stroke volume under the regulation of baroreflex in arotic sinus. The proposed heart activity baroreflex regulation model contains CVS electric circuit sub-model, baroreflex regulation sub-model and time delay sub-model. In these models, applied electric circuit sub-model is researched by B.C.Choi and the baroreflex regulation sub-model transforms the input, the arotic pressure of CVS electric circuit sub-model, to outputs, heart period and stroke volume by mathematical nonlinear feedback. We constituted the time delay sub-model to observe sensitivity of heart activity baroreflex regulation model by using the variable value to represent the control signal transmission time from the output of baroreflex regulation model to efferent nerve through central nervous system. The simulation object of this model is to observe variability of the CVS by variable value in time delay sub-model. As simulation results, we observe three patterns of CVS variability by the time delay. First, if the time delay is over 2.5 sec, arotic pressure, stroke volume and heart rate is observed nonperiodically and irregularly. Second, if the time delay is from between 0.1 sec and 0.25 sec, the regular oscillation is observed. Finally, if time delay is under 0.1 sec, then heart rate and arotic pressure-heart rate trajectory is maintained in stable state.