• Wind and Structures
• /
• v.16 no.4
• /
• pp.373-391
• /
• 2013

This is the first of two companion papers that analyse ten years of on-site monitoring data for the Confederation Bridge to determine the validity of the original wind speeds and wind loads predicted in 1994 when the bridge was being designed. The check of the original design values is warranted because the design wind speed at the middle of Northumberland Strait was derived from data collected at shore-based weather stations, and the design wind loads were based on tests of section and full-aeroelastic models in the wind tunnel. This first paper uses wind, tilt, and acceleration monitoring data to determine the static and dynamic responses of the bridge, which are then used in the second paper to derive the static and dynamic wind loads. It is shown that the design ten-minute mean wind speed with a 100-year return period is 1.5% less than the 1994 design value, and that the bridge has been subjected to this design event once on November 7, 2001. The dynamic characteristics of the instrumented spans of the bridge including frequencies, mode shapes and damping are in good agreement with published values reported by others. The on-site monitoring data show bridge response to be that of turbulent buffeting which is consistent with the response predicted at the design stage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.4
• /
• pp.662-674
• /
• 1997

In order to post process the vector-quantized images employing the theory of projections onto convex sets or the constrained minimization technique, the the projector onto QCS(quantization constraint set) as well as the filter that smoothes the lock boundaries should be investigated theoretically. The basic idea behind the projection onto QCS is to prevent the processed data from diverging from the original quantization region in order to reduce the blurring artifacts caused by a filtering operation. However, since the Voronoi regions in order to reduce the blurring artifacts caused by a filtering operation. However, since the Voronoi regions in the vector quantization are arbitrarilly shaped unless the vector quantization has a structural code book, the implementation of the projection onto QCS is very complicate. This paper mathematically analyzes the projection onto QCS from the viewpoit of minimizing the mean square error. Through the analysis, it has been revealed that the projection onto a subset of the QCS yields lower distortion than the projection onto QCS does. Searching for an optimal constraint set is not easy and the operation of the projector is complicate, since the shape of optimal constraint set is dependent on the statistical characteristics between the filtered and original images. Therefore, we proposed a hyper-cube as a constraint set that enables a simple projection. It sill be also shown that a proper filtering technique followed by the projection onto the hyper-cube can reduce the quantization distortion by theory and experiment.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.64-71
• /
• 2001

In this paper the ball-on-disk type sliding tests with boundary lubricated steels were carried out to verify the relation between surface profiles and wear as well as scuffing. Three kinds of surface roughness and asperity radius were produced on AISI 1045 steels using the different processes of grinding and polishing. Frictional forces and time to scuffing were measured. Also, the shape and amount of wear particles were analyzed to compare with original profiles. From the tests, it was confirmed that the size of wear particles are very related to original surface profile. The time to failures and wear amounts were sensitive to the surface spacing. The large surface spacing shows much longer sliding life and smaller wear amount than the others. Time to scuffing was increased with increasing surface profile spacing. The size of wear particles was increased and the amount was decreased with increasing surface profile spacing. Wear volume and wear rate K were decreased with increasing surface profile spacing. And after sliding tests, surface cracks of inner parts of the wear track occurred scuffing were observed and compared the differences about each specimen having the different surface profile spacing.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.2
• /
• pp.120-135
• /
• 2021

Changdeokgung Rear Garden is an important place to show the essence of the garden culture of the Joseon Dynasty. In the garden landscape experience, the restoration of the road completes the system of connecting the main spaces. Therefore, the restoration of the road requires accurate understanding of its creation, extinction, and maintenance. The purpose of this study was to detail the changes in the path that occurred in the Changdeokgung Palace Rear Garden from the late Joseon Dynasty to the modern and contemporary period by analyzing literature and drawing materials. For a time-series analysis, "Donggwoldo" and "Donggwoldohyeong" produced in the Joseon Dynasty, along with "Changdeokgung Plan Drawing" produced in modern and contemporary times, and aerial photographs were used. Drawings and photographs of different coordinate systems were transformed into one coordinate system in the geographic information system ArcGIS to compare changes in the movements of different periods. The results of the study are as follows. First, a total of 37 sections have been used since Japanese colonial era, of which 13 have been maintained, 14 have disappeared, and 10 have been newly established. Among the extinction sections, the road north of Neungheojeong Pavilion is considered to be an urgent place to connect the space to the garden and restore it to enjoy the scenery. In the new section, it seems necessary to establish a new alternative road or shorten the section for the connecting section between Daebodan and Okryucheon. Second, it was revealed that the biggest and most frequent changes to the road system in the garden were Japanese colonial era and renovations in the 1970s. It is worth noting the changes in the road since the 1970s, rather than Japanese colonial era, where it was difficult to manage the gardens independently. The access road to Okryucheon remained in its original shape until the 1990s, but it was renovated to its current shape due to misperception of the original shape. A project is needed to find out the cause of the change in this period and restore the damaged original shape. The biggest achievement of this study is that it revealed the changes in the garden path of Changdeokgung Palace in modern and contemporary times. The biggest achievement of this study is that it revealed the changes in the road of Changdeokgung Palace Rear Gardens in modern and contemporary times. However, there is a limitation that it has not been able to clearly present the location and shape that should be restored because it has not found data on landscaping plans or maintenance. In order to restore the road using the data revealed in this study, it seems necessary to consider realistic problems such as current space utilization, viewing system, disaster prevention and maintenance.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.13 no.2
• /
• pp.103-119
• /
• 2011

This study set out to analyze the solid shapes of knit flared skirts, which are best represented in a 3-dimensional shape for all knit skirts, according to the seamed and seamless production method and to estimate the silhouettes of knit flared skirts based on the results. It also aimed to help with the introduction and spread of seamless weaving by revising and supplementing potential problems and provide findings that would be put to active use as basic data, thus contributing to the development of original knitwear and offering fundamental materials for the development of the knitting industry. A number of experimental knit flared skirts were made according to skirt angle ($90^{\circ}$ and $180^{\circ}$), gauge (7G, 12G, and 15G), and grain (bias, wale, and radial), including 12 kinds of seamed knit flared skirts and 6 kinds of seamless knit flared skirts. Using a three-dimensional shape measurement system, the investigator measured the cross-sectional shapes of their hemlines. The SPSS 12 Version program was used for statistical processing, and descriptive statistics such as mean and standard deviation were used to compare the seamed and seamless knit flared skirts in the measurements (measurement items) of their solid shapes according to the width, gauges, and grain directions. The central grain direction of seamless knit flared skirts was in a radial form and even hemlines, thus presenting a beautiful appearance and solid shape. The 3-dimensional shapes show that seamless knit flared skirts are superior to seamed ones. The research findings are expected to open a door for Korea's knitting industry to quickly respond to small quantity batch production and additional orders.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.4
• /
• pp.1738-1756
• /
• 2020

To improve the accuracy and realism of the virtual surgical simulation system, this paper proposes an optimized mass-spring model with shape restoration ability based on volume conservation to simulate soft tissue deformation. The proposed method constructs a soft tissue surface model that adopts a new flexion spring for resisting bending and incorporates it into the mass-spring model (MSM) to restore the original shape. Then, we employ the particle swarm optimization algorithm to achieve the optimal solution of the model parameters. Besides, the volume conservation constraint is applied to the position-based dynamics (PBD) approach to maintain the volume of the deformable object for constructing the soft tissue volumetric model base on tetrahedrons. Finally, we built a simulation system on the PHANTOM OMNI force tactile interaction device to realize the deformation simulation of the virtual liver. Experimental results show that the proposed model has a good shape restoration ability and incompressibility, which can enhance the deformation accuracy and interactive realism.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.4
• /
• pp.44-52
• /
• 2003

Shape memory alloys (SMA) are often used in smart structures as active components. Their ability to provide large recovery forces and displacements has been useful in many applications, including devices for artificial muscles, active structural acoustic control, and shape control. Based on the 3-dimensional SMA constitutive equation in this paper, the radial displacement control of externally pressurized circular and semicircular composite cylinders under external pressure with a thin SMA layer bonded on its inner surface or inserted between composite layers in investigated using 3-dimensional finite element analysis. Upon actuation through resistive heating, SMAs start to transform from martensitic into austenitic state, simultaneously recover the prestrain, and thus cause the composite cylinders to go back to their original shapes of the cylinder cross-sections.

• Restorative Dentistry and Endodontics
• /
• v.13 no.1
• /
• pp.161-171
• /
• 1988

The purpose of this study was to examine the morphological changes of different simulated canals according to the preparation procedures. With the use of clear casting resin, simulated straight and curved canals were created so that canal preparation procedures could be directly visualized and compared. Thirty clear polyester casting resin blocks which contained four simulated canals divided into three groups; Group A($0^{\circ}$), Group B($15^{\circ}$), and Group C($30^{\circ}$). In each block, 3 canals were prepared different preparation techniques, which were conventional method, step-back method, and giromatic filing. But, one canal was not prepared as a control group. The results were as follows: 1. There was no difference on canal shape among three canal preparation methods in straight canals (Group A). 2. When conventional method and Giromatic filing were used in curved canals (Group B, C), elbow, zip and hour-glass shape were formed in apical third. 3. When conventional method and Giromatic filing were used in curved canals (Group B, C), tear-drop appearance developed at the site of the canal exit in curved canals. 4. In curved canals (Group B, C), file tend to straighten within the canal. 5. There was no difference on canal shape according to curved angle in step-back method (p > 0.1). But there was significant difference on canal shape according to curved angle in conventional method and Giromatic filing (p < 0.001). 6. Step-back method was significantly more effective than conventional method and Giromatic preparation in morphologic aspects of apical third of original canals.

• Smart Structures and Systems
• /
• v.17 no.5
• /
• pp.819-835
• /
• 2016

In this paper, the activities carried out within the EU funded Clean Sky Joint Technology Initiative (JTI GRA) Project and aimed at developing a morphing flap, are illustrated. The reference device is a regional aircraft single slotted flap, enhanced with deforming capabilities to obtain improved hyper-lift performance. The design started with the identification of the internal architecture, intended to allow camber variations. A concentrated-hinge architecture was selected, for its ability to fit different curvatures and for the possibility of easily realizing an "armadillo-like" configuration, then avoiding the use of a complicate deformable skin. The flap layout is made of segmented ribs, elastically hinged each other and span-wise connected by conventional spars. Relative rotations of the rib elements are forced by SMA structural actuators, i.e., cooperating in the external loads absorption. Super-elastic SMA are used to make up recovery elastic elements, necessary to regain the original shape after activation. These further elements in turn contribute to the overall flap rigidity. After assessing the hinge number and the size of the SMA active and passive elements, the advanced design phase was dealt with. It was aimed at solving manufacturing issues and producing the executive drawings. The realized demonstrator was finally tested in lab conditions to prove its functionality in terms of whether target shape actuation or attained shape preservation under loads. On the basis of the numerical results and the experimental outcomes, precious hints were obtained for further developments of the concept.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.15 no.2
• /
• pp.77-89
• /
• 2013

This study investigated the formation of silhouette and hemline shape of knit flare skirts according to the properties of knit material through virtual clothing with a 3D virtual clothing system called i-Designer of Technoa, thus building a database of the property data of knit material to reduce the number of sample making steps repeated and implemented several times in the process of clothes making. The results would help to estimate a silhouette in advance, offer assistance to the development of original knit wear, and explore ways to provide basic data for the development of the knit industry of the nation. The investigator made 12 kinds of experimental clothes to the angles(width of skirt: $90^{\circ}$ and $180^{\circ}$), gauge(7G, 12G, and 15G), and grain directions(wale and bias direction) of experimental clothes for virtual clothing. The dynamic characteristics of knit skirt samples according to each gauge were measured with the KES-FB system. Draper shapes were analyzed with the sectional shape data of hemline based on i-Designer. As for the measurements of the sectional shape of hemline and the formation of silhouette, the number of nodes, the average height of node mountains and valleys, and the hemline width right and left and before and after increased at the angle of $180^{\circ}$ than $90^{\circ}$. As gauges multiplied, the number of nodes, and silhouette angle dropping. When considering grain directions, the number of nodes and silhouette index increased in the wale direction at the angle of $90^{\circ}$ with the number of nodes and silhouette angle increasing in the wale direction at the angle of $180^{\circ}$.