• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1460-1463
• /
• 2005

In this paper, analysis of magnetic marker for autonomous vehicle guidance system using 3-axis magnetic sensor propose. Position sensing is an important an estimation system of vehicle position and orientation on magnetic lane, which is a parameter of the steering controller for automated lane following is described. To verify that the magnetic dipole model could be applied to a magnetic unit paved in roadway, the analysis of the data 3-axis magnetic field measured experimentally.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.231-233
• /
• 2007

In this paper we present a new visual approach for the robust bin-picking in a two-step concept for a vision driven automatic handling robot. The technology described here is based on two types of sensors: 3D laser scanner and CCD video camera. The geometry and pose(position and orientation) information of bin contents was reconstructed from the camera and laser sensor. these information can be employed to guide the robotic arm. A new thinning algorithm and constrained hough transform method is also explained in this paper. Consequently, the developed bin-picking demonstrate the successful operation with 3D hole object.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.11a
• /
• pp.257-262
• /
• 2004

The purpose of data fusion is collecting maximized information from combining the data attained from more than two same or different kind sensor systems. Data fusion of same kind sensor systems like optical imagery has been on focus, but recently, LIDAR emerged as a new technology for capturing rapidally data on physical surfaces and the high accuray results derived from the LIDAR data. Considering the nature of aerial imagery and LIDAR data, it is clear that the two systems provide complementary information. Data fusion is consisted of two steps, alignment and matching. However, the complementary information can only be fully utilized after sucessful alignment of the aerial imagery and lidar data. In this research, deal with centroid of building extracted from lidar data as control information for estimating exterior orientation parameters of aerial imagery relative to the LIDAR reference frame.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.14 no.1
• /
• pp.41-48
• /
• 2014

This paper analyzes the Monte Carlo localization (MCL) method, which estimates the pose of an indoor mobile robot. A mobile robot must know where it is to navigate in an indoor environment. The MCL technique is one of the most influential and popular techniques for estimation of robot position and orientation using a particle filter. For the analysis, we perform experiments in an indoor environment with a differential drive robot and ultrasonic range sensor system. The analysis uses MATLAB for implementation of the MCL and investigates the effects of the control parameters on the MCL performance. The control parameters are the uncertainty of the motion model of the mobile robot and the noise level of the measurement model of the range sensor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.815-819
• /
• 1998

The silicon-nirtide membrane structure for IR sensor was fabricated through the etching and the direct bonding. The PRO($PbTiO_3$ ) layer for a IR detection was coated on the membrane and its characteristics were measured. The a attack of PTO layer during the etching of silicon wafer as well as the thermal isolation of the IR detection layer were eliminated through the method of bonding/etching of silicon wafer. The surface roughness of the membrane was measured by AFM, the micro voids and the non-contacted area were inspected by the PTO layer were measured, too.

• Advances in aircraft and spacecraft science
• /
• v.2 no.3
• /
• pp.263-273
• /
• 2015

Carbon nanotube strain sensors, or so called "fuzzy fiber" sensors have not yet been studied sufficiently. These sensors are composed of a bundle of fiberglass fibers coated with CNT through a thermal chemical vapor deposition process. The characteristics of these fuzzy fiber sensors differ from a conventional nanocomposite in that the CNTs are anchored to a substrate fiber and the CNTs have a preferential orientation due to this bonding to the substrate fiber. A numerical model was constructed to predict the strain response of a composite with embedded fuzzy fiber sensors in order to compare result with the experimental results obtained in an earlier study. A comparison of the numerical and experimental responses was conducted based on this work. The longitudinal sensor output from the model matches nearly perfectly with the experimental results. The transverse and off-axis tests follow the correct trends; however the magnitude of the output does not match well with the experimental data. An explanation of the disparity is proposed based on microstructural interactions between individual nanotubes within the sensor.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.1
• /
• pp.38-43
• /
• 2009

In this paper. a prototype of a mobile Sun tracking system is proposed. The proposed system uses 2-axis tilt sensor and 3-axis magnetic sensor to measure the orientation and the posture of the system according to the horizontal system of coordinates, which are used to compensate the slope effects. Then through astronomical calculation using the time and position information obtained by GPS sensor the azimuth and altitude of the Sun from that location is calculated. The position of the Sun is converted to that of the mobile Sun tracking system coordinates and used to control A-axis and C-axis of the system.

• Proceedings of the KOSOMBE Conference
• /
• v.1993 no.11
• /
• pp.44-47
• /
• 1993

In this paper, the wall follwing method of a motorized wheelchair is discussed. The wall fellowing problem is characterized by maintaining a constant distance to the wall, which should be possible using a distance measuring sensor only. Ultrasonic sensors are cheap are fairly simple to use in this case. The main problem is the calculation of the distance and orientation of the wheelchair with respect the wall from the sensor data. This is solved by the method that sensor data is obtained from 3 ultrasonic sensors arranged at a same perpendicular pivot. The results show that a new method is very effiecient for a motorized wheelchair.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.6A
• /
• pp.481-487
• /
• 2005

In order to increase the autonomous navigation capability of a mobile robot, it is very crucial to develop a method for recognizing a priori known environmental characteristics. This paper proposes an ultrasonic sensor based real-time method for recognizing a priori known indoor environmental characteristics like a wall and corner. The ultrasonic sensor consists of an ultrasonic transmitter and two ultrasonic receivers placed symmetrically about the transmitter. Unlike previous methods the information obtained from the sensor is processed in real-time by extended Kalman filter to be able to correct the position and orientation of robot with respect to known environmental characteristics.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.8
• /
• pp.579-584
• /
• 2016

When surgical instruments are tracked in an image-guided surgical navigation system, a stereo vision system with high accuracy is generally used, which is called optical tracker. However, this optical tracker has the disadvantage that a line-of-sight between the tracker and surgical instrument must be maintained. Therefore, to complement the disadvantage of optical tracking systems, an internal vision sensor is attached to a surgical instrument in this paper. Monitoring the target marker pattern attached on patient with this vision sensor, this surgical instrument is possible to be tracked even when the line-of-sight of the optical tracker is occluded. To verify the system's effectiveness, a series of basic experiments is carried out. Lastly, an integration experiment is conducted. The experimental results show that rotational error is bounded to max $1.32^{\circ}$ and mean $0.35^{\circ}$, and translation error is in max 1.72mm and mean 0.58mm. Finally, it is confirmed that the proposed tool tracking method using an internal vision sensor is useful and effective to overcome the occlusion problem of the optical tracker.