• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.4
• /
• pp.636-644
• /
• 2009

This paper presents a compact, low insertion loss, sharp rejection and wide band microstrip band pass filter that is composed rectangular loop resonator and step-impedance-open-stub(SIOS) for wireless data communication. The SIOS can be reduce length about 30% more than general $0.25{\lambda}$ stub. And the stub can the advantage of tuning impedance magnitude. In order to demonstrate agrement of this paper prove, the optimized wide band pass filters are realized and experimented. A transmission line model used to calculate the frequency response of the new filters shows good agreement with measurements. The filter has 3dB fractional bandwith of 52.5%(3.267GHz), an insertion loss of better than 0.33dB from 4.587GHz to 7.854GHz, and two rejection of greater than 30dB within 221MHz$(4.366GHz{\sim}4.587GHz)$ at low frequency band, 181MHz$(7.854GHz{\sim}8.035GHz)$ at high frequency band. Maximum rejection characteristics of the filter are -54dB at low frequency and -60dB at high frequency.

• Journal of the Korean Data and Information Science Society
• /
• v.26 no.3
• /
• pp.639-652
• /
• 2015

In today's manufacturing environment, the process data can be easily measured and transferred to a computer for analysis in a real-time mode. As a result, it is possible to monitor several correlated quality variables simultaneously. Various multivariate statistical process control (MSPC) procedures have been presented to detect an out-of-control event. Although the classical MSPC procedures give the out-of-control signal, it is difficult to determine which variable has caused the signal. In order to solve this problem, data mining and machine learning techniques can be considered. In this paper, we applied the technique of decision tree learning to the MSPC, and we did simulation for MSPC procedures to monitor the bivariate normal process means. The results of simulation show that the overall performance of the MSPC procedure using decision tree learning technique is similar for several values of correlation coefficient, and the accurate classification rates for out-of-control are different depending on the values of correlation coefficient and the shift magnitude. The introduced procedure has the advantage that it provides the information about assignable causes, which can be required by practitioners.

• The Korean Journal of Food And Nutrition
• /
• v.10 no.3
• /
• pp.401-406
• /
• 1997

This study was carried out to compare the extractability and ATPase activity of actomyosin extracted shank, rib and loin muscle of beef meat stored at 8$^{\circ}C$. The extractability of actomyosin in shank, rib and loin muscle were 36.74, 72.55 and 56.77mg/g early in the storage, respectively. The extractability of the rib and loin muscle were similar, the shank muscle was processed differently with their. The Mg- and Ca-ATPase activity of the shank muscle rised to 3 days, but decreased the 6th day. And Mg- and Ca-ATPase activity of the rib muscle was similar during storage period, the loin muscle made a slow descent. The strength of Mg- and Ca-ATPase activity showed in the order shank, rib and loin muscle. The EDTA-ATPase activity of the shank and rib muscle was difference according to storage period and ionic strength, but the loin muscle was increase in succession with magnitude of ionic strength.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.193-203
• /
• 2004

Arching effects in backfill materials generate a nonlinear active earth pressure distribution on a rigid retaining wall with rough face, and arching effects on the shape of the nonlinear earth pressure distribution depends on the mode of wall movement. Therefore, the practical shape of failure surface and arching effect in the backfill changed with the mode of wall movement must be considered to calculate accurate magnitude and distribution of active earth pressure on the rigid wall. In this study, a new formulation for calculating the active earth pressure on a rough rigid retaining wall rotating about the base is proposed by considering the shape of nonlinear failure surface and arching effects in the backfill. In order to avoid mathematical complexities in the calculation of active earth pressure, the imaginary failure surface composed of four linear surfaces is used instead of the nonlinear failure surface as failure surface of backfills. The comparisons between predictions from the proposed equations and existing model test results show that the proposed equations produce satisfactory predictions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.893-898
• /
• 2017

A TDC(Time-to-Digital Converter) of counter-type is designed by $0.18{\mu}mCMOS$process and the supply voltage is 1.5 volts. The converted error of maximum $T_{CK}$ is occurred by the time difference between the start signal and the clock when the period of clock is $T_{CK}$ in the conventional TDC. And the converted error of -$T_{CK}$ is occurred by the time difference between the stop signal and the clock. However in order to compensate the disadvantage of the conventional TDC the clock is generated within the TDC circuit and the clock is synchronized with the start and stop signals. In the designed TDC circuit the conversion error is not occurred by the difference between the start signal and the click and the magnitude of conversion error is reduced (1/2)$T_{CK}$ by the time difference between the stop signal and the clock.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.1
• /
• pp.201-208
• /
• 1999

In recent years, strengthening by steel plate, carbon fiber sheets, and carbon fiber laminate is spotlighted in order to repair and rehabilitation of R/C structures. In this study, 3 methods of rehabilitation technique were analyzed from the test results. Test parameters were the width of cracks, the method of repair and rehabilitation, the magnitude of pre-load. Deflections, failure loads, strains of reinforcing bar, strains of carbon fiber sheet, carbon fiber laminate and steel plate were measured during the tests. The primary purpose of this research was to analyze the failure mode and structural behavior of strengthened RC beams with/without superimposed pre-load. Test results should that no significant difference was observed between with pre-loaded specimens and no-loaded specimens during rehabilitation.

• Explosives and Blasting
• /
• v.27 no.1
• /
• pp.7-20
• /
• 2009

In this study, 5 steps of different delay intervals are applied to a plasma rock-breaking machine that is driven by electric shocks in order to improve the workability of the traditional single-shot type plasma rock-breaking operation. The sequential steps use the electrolyte volume per delay of 1, 2, 3, 4, 5 kg and it has been analyzed to measure the delay time and level of the ground vibration and noise according to exploding. The delay time of the rock-breaking machine by an electric shock of 5 steps has used about 40~50ms at the electrolyte connected from 1 to 3 holes, about 70~80ms at the electrolyte connected from 4 to 5 holes. It is identified that the extents of the ground vibration is low to 1 over 3~6 compared with that of the emulsion explosives.

• The Korean Journal of Applied Statistics
• /
• v.20 no.1
• /
• pp.195-204
• /
• 2007

In order to represent multiple regression data, an alternative graphical method, called as SSR Plot, is proposed by using geometrical description methods. This plot uses the relation that the sum of sqaures for regression (SSR) of two explanatory variables is known as the sum of the SSR of one variable and the increase in the SSR due to the addition of other variable to the model that already contains a variable. This half circle shaped SSR plot contains vectors corresponding explanatory variables. We might conclude that some explanatory variables corresponding to vectors which locate near the horisontal axis do affect the response variable. Also, for the regression model with two explanatory variables, a magnitude of the angle between two vectors can be identified for suppression.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.1
• /
• pp.1-11
• /
• 2009

Although the exterior wood such as column may frequently contact with liquid water, little work has been found to measure liquid water absorption in wood. To investigate the moisture diffusivity of wood in the longitudinal direction including bound water and free water movement, liquid water absorption test was conducted at the room temperature. The order of magnitude for absorption coefficient and diffusivity was Japanese elm, horn beam, hemlock, spruce, radiata pine, and painted maple. The Boltzmann transformation method was used to determine the diffusivity from measured moisture content distributions in the absorption test. The shape of the curve representing the dependence of diffusivity with moisture content was similar in test samples. The diffusivity decreased with increasing moisture content until around the fiber saturation point and then increased at the nonhygroscopic region, which ranged from $10^{-10}$ to $10^{-7}m^2/s$.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.6
• /
• pp.350-360
• /
• 2016

In order to investigate characteristics of waves and currents varying in space in the Haeundae coast in winter, numerical simulations by using a 2-D spectral wave model(SWAN) and 2-DH hydrodynamic model(Delft3D) were carried out in this study. The results of numerical simulations were validated with the field data collected at several different locations in the study area in February, 2014. From the numerical simulations, it was found that waves and currents were significantly influenced in terms of direction and magnitude by bottom topography characterized by straggling rock crops covered with sea grasses. The coupling of SWAN and Delft3D models also revealed that alongshore currents directing from the east to the west were developed in the nearshore, due to the influence of larger waves with the main incident direction from the east.