• Transactions of Materials Processing
• /
• v.14 no.3 s.75
• /
• pp.277-281
• /
• 2005

LTCC(Low temperature co-fired ceramic) is being recognized as a significant packaging material of electrical devices for the advantages such as relatively low temperature being needed for process, low conductor resistance and high printing resolution. In the process of LTCC electrical devices, the punched via-hole quality is one of the most important factors on the performance of the device. However, its mechanism is very complicated and optimization of the process seems difficult. In this paper, to clarify the process, via-hole punching experiments were carried out and the punched holes were examined in terms of their burr formation. The effects of thickness of PET sheet, ceramic sheet and punch-to- die clearance on via-hole quality were also discussed. Optimum process conditions are proposed and a factor $\kappa$ is introduced to express effect of the process variables.

• Transactions of Materials Processing
• /
• v.10 no.2
• /
• pp.123-129
• /
• 2001

This study is to investigate the effects of cold forming method with steel sheet of SCP3C to improve continuous productivity. Experiments were carried out in various working conditions, such as the number of stamping and the punch temperature. The effects of the punch temperature and the number of stamping on drawability of steel sheet of SCP3C as well as clearance and draw-in in the number of stamping were examined and discussed. More improvement of continuous productivity in case of cold stamping rather than by conventional stamping at room temperature is obtained. The optimum forming condition for drawing trunk floor panel of SCP3C is shown as the punch is cooled by coolant of $-5^{\circ}C$ and at the same time both the die and the blankholder are heated by stamping and frictional heat.

• Transactions of Materials Processing
• /
• v.23 no.4
• /
• pp.244-249
• /
• 2014

The thixoforming process has been applied to forming of a joint node for the aluminum frame of a low speed electric vehicle. A joint node should connect three aluminum extruded chassis showing different profiles. The MHS(magnetohydrodynamic stirring) A357 billet was selected because homogeneous globular grains are necessary as the billet materials for thixoforming. A careful design of joint node has been performed by the considerations of structural demands and the simulation results for the thixoforming process using the MAGMAsoft. Optimum heating temperature for the A357 billet was between 580 and $585^{\circ}C$ corresponding to the semi-solid temperatures showing 20-30% of liquid fraction. An injection speed of around 100mm/s and preheating of die at temperatures of $200^{\circ}C$ were also necessary conditions to obtain reasonable thixoformed parts.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.10a
• /
• pp.105-112
• /
• 1996

Aluminium alloy have been used extensively as forging materials for aircraft components due to their high specific strength and corrosion resistance. A large portions of these materials are used as airframe components consisted of various combination of such Rib-Web structure. But the problem of high forging pressure and defect which were caused by narrow Rib thickness prevented from the favorable developments and laboratory scaled trials. In this study, optimization of forging variables such as corner radius and temperature in Rib-Wed structure were established. The 2 mm of corner radius minimized the forging pressure to get the fixed Rib height, which well coincided with theoretical result according to Upper-Bound analysis. And optimum workpiece temperature was below 450$^{\circ}C$ in consideration of grain growth and forging defects by local melting.

• Transactions of Materials Processing
• /
• v.6 no.6
• /
• pp.517-526
• /
• 1997

The purpose of this study is to investigate changes in the wall thickness of tube sinking and working forces by the upper bound method and ABAQUS code. The independent variables are ; workpiece material, original wall thickness of tube, die angle, friction, and reduction of diameter. The results indicate that these five variables are factors of the increase in wall-thickness and working forces. Three variables, a inner tube wall angle and two angles of the velocity discontinuous surfaces, are optimized in this proposed velocity field by the upper bound method. In this method, we can estimate the working forces and final tube thicknesses similar to actual forming process. Optimum process variables which are obtained by upper bound method are used in ABAQUS pre-model.

• Transactions of Materials Processing
• /
• v.18 no.3
• /
• pp.251-255
• /
• 2009

Since fastener bolt for airplane require high specific strength and corrosion resistance, Ti-6Al-4V alloy is widely used. However, the Ti-6Al-4V bolt is generally manufactured by cutting and rolling because of their poor workability. The aim of present work is to develop hot forming technology for high strength Ti-6Al-4V. Various heat-treatments were applied to specimen in order to increase hot-workability and prevent galling with die. Multiple forging were simulated with FE code to determine optimum process parameters including specimen temperature, strain rate, local strain, and thermal shrinkage. Forged samples were heat-treated again to increase their mechanical properties.

• Transactions of Materials Processing
• /
• v.22 no.7
• /
• pp.389-393
• /
• 2013

One of the most efficient designs for manufacturing LNG tank is the Moss spherical type because it has been validated through precise analyses with respect to reliability and construction safety by stress analysis. The Moss spherical tank is assembled with hundreds of Al thick plate patches that are deformed to curved shape at elevated temperature and welded together. It is essential to evaluate the amount of deflection in the Al5083 thick plate when the patch is transferred from the heating chamber to the forming die since the patch has a length of 12,000 mm and a thickness of 60 mm. Based on FE analysis results, a design procedure for minimizing deflection in Al5083 thick plate during transfer using a moving carrier is demonstrated in this paper.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.641-645
• /
• 2002

In case of aluminum-cased battery, The ratio of height and base of square is generally above the ten times, square-shaped and problem of non-axis symmetry. It is typical model to set up the analysis method of finite element. The reliable analysis of finite element method is suggested, which is used to investigate the possibility that multi-stage deep drawing and ironing used currently is replaced by backward impact extrusion favorable in the respect of cost production and productivity. The influence of parameter was analyzed and compared, which was considered to analyze the process of large deformation plasticity such as extrusion. Die and billet was made as the same shape of finite element model. The results of experiment show good forming without the rupture and wrinkles with the optimum velocity 100mm/sec obtained by analysis.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.53-56
• /
• 2007

Magnesium sheet used in electrical device due to mobility and EMF shielding characteristics. Magnesium case by press forming was advantageous compare with conventional die casting process, because of its thin gauge of wall and surface quality. But it need to makes the boss to fix inner part or assemble the case. CD stud welding was effective way for joining the boss to the thin gauge case of the electrical devices. In this study, we investigated the performances of the magnesium boss welder To measure the process parameters such as the force and the weld current, we design the monitoring system for CD stud welding. We test the characteristics of CD stud welding for AZ31 sheets at some variables. Finally we select the optimum welding range of magnesium sheets in CD stud welding process.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.175-181
• /
• 2008

The technologies of mold design, manufacturing, injection molding process and computer aided engineering(CAE) are developed rapidly with the growth of plastic product market. Injection molding process optimum design can not be easily determined. This study was determined factors and levels which carried out to analyze an influence of narrow pitch BGA socket warpage and performed investigating the main effect and interaction effect between factors using design of experiment. The result of this paper is injection time and packing pressure are affect on narrow pitch BGA socket warpage at injection molding.