• Korean Journal of Optics and Photonics
• /
• v.21 no.1
• /
• pp.1-5
• /
• 2010

In this study, we propose a grating structure using guided-mode resonance (GMR) to increase the absorption efficiency of a silicon solar cell. The proposed solar cell design consists of a one-dimensional diffraction grating and a planar waveguide layer of poly-silicon deposited on a silver reflector. We investigate the influence of structure parameters such as grating period, waveguide thickness, grating width and grating depth. Optimal parameters are found using the particle swarm optimization (PSO) algorithm. In the optimized GMR-assisted solar cell, absorption efficiency up to 65.8% is achieved in the wavelength range of 300 nm~750 nm.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.2
• /
• pp.47-53
• /
• 2012

Recently, by the increasing of data transmission rates, PCB is required high-speed data transmission rates and thin packaging. So optical PCB which is the combination of electrical layer and optical layer can be one of the solution to overcome the limitations of conventional electrical PCB. The most important factor in the implementation of optical PCB is optical interconnection. So the research on high-efficiency and passive alignment has been active. In this paper, we suggest built-in lens pluggable waveguide and we simulate its coupling efficiency and structural stability. Optical simulation results show that the proposed structure has higher efficiency than no lens structure about 1.86 times in transmitter and about 1.42 times in receiver. In structure simulation, inner lens has no damage in desorption process. Therefore, we shown that the proposed structure has a high coupling efficiency and structural stability.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.303-306
• /
• 2005

In this paper, a CPW-fed monopole antenna using inverted L-type DGS structures is proposed and investigated experimentally. The proposed antenna is fabricated into FR4 substrate with dielectric constant($\varepsilon$r=4.5). Measured results show that the impedance bandwidth, determined from 10-dB return loss, for frequencies between 5.7250Hz-5.825CHz under the condition of VSWR$\leqq$2 is about 540MHg.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.4
• /
• pp.163-168
• /
• 2008

Photonic crystal structures have been received considerable attention due to their high optical sensitivity. One of the techniques to construct their structure is the dip-pen lithography (DPN) process, which requires a nano-scale resolution and high reliability. In this paper, we propose a two dimensional photonic crystal array to improve the sensitivity of optical biosensor and DPN process to realize it. As a result of DPN patterning test, we have observed that the diffusion coefficient of the mercaptohexadecanoic acid (MHA) molecule ink in octanol is much larger than that in acetonitrile. In addition, we have designed and fabricated optical waveguides based on the mach-zehnder interferometer (MZI) for application to biosensors. The waveguides were optimized at a wavelength of 1550 nm and fabricated according to the design rule of 0.45 delta%, which is the difference of refractive index between the core and clad. The MZI optical waveguides were measured of the optical characteristics for the application of biosensor.

• Korean Journal of Optics and Photonics
• /
• v.7 no.4
• /
• pp.375-385
• /
• 1996

Recently interest in the fabrication of LD operated by low current is gradually increasing as fabrication techniques of MQW-LD are progressed. In this viewpoint, theoretical estimation for decreasing the amount of threshold current will be helpful to design and make LD in case that active layer of conventional bulk type RWG-LD structure is replaced with MQW structure. Therefore, the optimum design condition of RWG MQW-LD was obtained from theoretical analysis in order to operate in the weakly index-guided LD and low threshold current. The lateral effective index step has been obtained in RWG MQW-LD structure. Waveguide mechanism including this index step has been investigated by solving the carrier diffusion equation and lateral wave equation. From these theoretical results, the optimum design condition of RWG MQW-LD have been suggested.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.6
• /
• pp.1369-1375
• /
• 2007

The recent, a large capacity of telecommunication networks is required in order to it is in proportion to capacity of information communication increase and to satisfy a demand because of the demand about Internet, a multimedia service of internet, Video of internet protocol(VoIP), Audio/Video streaming. As a result, DWDM(Dense Wavelength Division Multiplexing)technologies are emerging to be a prevailing the method of solving it without additional optical fiber network building and high-speed equipment. Therefore this thesis proposed the optical filter of fiber/multilayer slab coupled structure combining it to multilayer slab waveguide by polishing the cladding of one side of fiber to design the optical filter having these functions. When a separation distance of fiber and slab was $3{\mu}m$, The optical filter proposed as the simulation result was satisfied with a DWDM filter characteristic with FWHM of 0.1nm on TM mode and TE mode as 32nm polarization independence in a communication window of $1.3{\mu}m$ when center wavelength was each ${\lambda}_0=1.274755{\mu}m$ and ${\lambda}_0=1.30591{\mu}m$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.7
• /
• pp.1359-1366
• /
• 2007

The recent, a large capacity of communication is required in order to it is in proportion to capacity of information communication increase and to satisfy a demand because of the demand about Internet, a multimedia service of Video of internet protocol(VoIP), Audio/Video steaming. DWDM(Dense Wavelength Division Multiplexing) technique has been emerged as the method of solving it without additional optical fiber network building and hish-speed equipment. Therefore this thesis proposed the optical filter of fiber/multilayer slab coupled structure combining it to multilayer slab waveguide by polishing the cladding of one side of fiber to design the optical filter having these functions. The optical filter proposed as the simulation result satisfies DWDM filter characteristic; 1) when the separation distance between fiber and slab is $4.15{\mu}m$ at the communication window of $1.5{\mu}m$, the polarization independence is 65nm, 2) when the center wavelengths about TM mode and TE mode are each ${\lambda}_0=1.54946\;{\mu}m$ and ${\lambda}_0=1.6144\;{\mu}m$ and, FWHM(Full at Half Maximun) is 0.1nm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.12B
• /
• pp.2335-2341
• /
• 1999

The $2\times32$ coupler consists of Mach-Zehnder interferometer and Y branch coupler. For the designs of this coupler, three dimensional rectangular core waveguide decomposed to two-dimensional structure by the effective index method. To optimize the waveguide structure, the confinement factor was investigated with two-dimensional finite difference Beam Propagation Method. The $2\times32$ coupler fabricated by simulation with height between Mach-Zehnder arms, H=$43.6\mu\textrm{m}$(path difference $0.668\mu\textrm{m}$) was showed best characteristics. In the results of dry etching of core layer, the etching rate of core layer was above 2600${\AA}$/min, the etching ratio of SiO2 to Al mask was 30:1 and the uniformity of etching was $\pm$5%. The maximum insertion loss and the uniformity of $2\times32$ coupler were below 19.2dB, 2dB respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.9
• /
• pp.1782-1792
• /
• 1994

Ti : $LiNbO_3$ traveling-wave phase optical modulators at wavelength 1.3㎛ have been designed and fabricated, focusing on the optical waveguide and asymmetric coplanar electrode structure. To improve the phase-mismatch of traveling-wave ACPS electrode, the characteristic impedance, effective microwave index, and electrode loss have been presented as a function of geometric parameters including electrode and buffer layer thickness. Low-loss channel optical waveguides on $LiNbO_3$ were fabricated by the Ti diffusion method with $O_2$ water-vapor environment. $2.5{\mu}m$ thick electrode was successfully fabricated by double-spin image reversal process. Modulation bandwidth was limited by a resonance at 2.9 GHz and modulation bandwidth up to 2.5GHz was approxirnately measured.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.4
• /
• pp.19-22
• /
• 2017

In this study, wavelength-free $1{\times}N$ optical splitter using a tapered polymer waveguide was studied to realize the transmission network of high-speed information communication network. Based on the evaluation of mode converting characteristics of splitter having two tapered multi-mode interference structures, an optimized structure of the $1{\times}N$ splitter was proposed for wide-range of input wavelength. 2D-BPM analysis $1{\times}8$ model showed that insertion loss of the proposed splitter is less than 10 dB for wavelength of input source from 1260 nm to 1650 nm.