• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.885-890
• /
• 1998

The electro-optical properties of polymer dispersed liquid crystals (PDLCs) depend on dispersion structures and nematic alignment which can be controlled by taking proper liquid crystal/polymer mixtures and process conditions. To achieve excellent electro-optical properties such as low driving voltage, good contrast ratio and negligible hysteresis, we have developed optimization procedure. Under the optimized conditions, PDLC of low threshold voltage less than 3.1 V, high contrast ratio more than 150 and negligible hysteresis were obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.119-122
• /
• 2001

ZnO thin films on (001) sapphire substrates have been deposited by pulsed laser deposition(PLD) technique at the oxygen pressure of 350 mTorr. In order to investigate the effect of post-annealing treatment with oxygenn pressure of 350 mTorr on the optical property of ZnO thin films, films have been annealed at various substrate temperatures after deposition. After post-annealing treatment in the oxygen ambient, the optical properties of the ZnO thin films were characterized by PL(Photoluminescence) and structural properties of the ZnO were characterized by XRD, and have investigated structural property and optical property for application of light emission device.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.31 no.11
• /
• pp.141-145
• /
• 1982

Optical absorption properties of an orphous Se film due to interband electronic transitions are observed in the visible range by varying the folm thickness. Amorphous Se films were prepared by evaporation method. As the experimental results, it is found that optical energy gap is around 2.07(e V), and the optical constants depend on the film thickness, evaporation-deposition conditions, and incident photon energy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.101-104
• /
• 1992

In-doped CdS thin films have been deposited at 150$^{\circ}C$ by simultaneous thermal evaporation of CdS and In. Deposition rate and film thickness were 8A/sec and about 1um, respectively. Indium doping concentration of films varied as Indium source temperature from 500$^{\circ}C$ to 700˚. Properties of In-CdS films have been investigatied by measurements of electrical resistivity, Hall effect, X-ray diffraction and optical trasmission spectra. The conductivity of these films was always n-type. The resistivity, carrier concentration, mobility and optical band gap dependence on Indium source temperature are reported. Carrier concentration and mobility of In-CdS films increased with increasing Indium source temperature: then they decreased. The variation of the optical band gap of In-CdS thin films are related to carrier concentration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.209-209
• /
• 2009

Fabrication of p-type ZnO has already proven difficult and usually inconsistent despite numerous worldwide efforts. Many research groups studied electrical and optical properties P, Li, As, N single doped ZnO thin film. In P-doped ZnO thin film, the reproducibility of p-type conduction with $P_2O_5$ as a dopant source was shown to be relatively poor. In this study, we made P single doped and Li & P co-doped ZnO target. To investigate electrical and optical properties of P single doped and Li & P co-doped ZnO thin film using $P_2O_5$ and $Li_3PO_4$ dopant source respectively was deposited by PLD. The growth temperature was changed 500, $700^{\circ}C$ and various oxygen partial pressure and post-annealing conditions was changed temperature, different gas ambient($O_2,N_2$). We investigate that how to change electrical and optical properties as function of growth temperature, oxygen partial pressure and post-annealing(RTA).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.176-179
• /
• 2003

ITO films on PET substrate were prepared by DC magnetron sputtering method using powdery target with different deposition conditions. In addition, the electrical and optical properties were investigated. As the sputtering power and working pressure were higher, the resistvity of ITO films increased. The optical transmittance deteriorated with increasing sputtering power and thickness. As the working pressure increased, however, the optical transmittance improved at visible region of light. From these results, we could deposited ITO films with $8{\times}10^{-3}\;{\Omega}-cm$ of resistivity and 80% of transmittance at optimal conditions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.4
• /
• pp.280-286
• /
• 2010

We have investigated the influence of rapid thermal annealing (RTA) temperature on properties of Al-doped zinc oxide (AZO) thin films deposited on glass substrate by using radio-frequency magnetron sputtering. The RTA is performed in a nitrogen ambient in the temperature range from 300 to $600^{\circ}C$ for 1 minute in a rapid thermal annealer after growing the AZO thin films. The crystallographic structure and the surface morphology of AZO thin film are measured by using X-ray diffraction, and atomic force microscopy and scanning electron microscopy, respectively. The optical transmittance of the deposited thin films is examined in the wavelength range of 300-1100 nm, where the average transmittance is above the 90% in the visible and near-infrared regions. The optical bandgap is calculated from the Tauc's model, and it shows a significant dependence on the RTA temperature. As for the electrical properties of the thin films, the AZO thin film annealed at $400^{\circ}C$ shows the lowest electrical resistivity of $8.6{\times}10^{-3}{\Omega}cm$ and the Hall mobility of $11.3cm^2$/V-sec. These results suggest that the RTA temperature is an important parameter to influence on the structural, electrical, and optical properties of AZO thin films.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.163-167
• /
• 2013

Aluminum doped zinc oxide (AZO) thin films have been prepared on the glass substrates (Corning 1737) by sol-gel dip-coating method employing zinc acetate and aluminum chloride hexahydrate for the transparent conducting oxide (TCO) applications. 1 at% Al was doped to the ZnO thin films. The effects of post-heating temperature on the crystallization, optical and electrical properties of the AZO films have been investigated. Experimental results showed that post-heating temperature affected the microstructure, electrical resistance, and optical transmittance of the AZO films. From the X-ray diffraction analysis, all films have hexagonal wurtzite crystal structure. Optical transmittance spectra of the AZO films exhibited transmittance higher than about 80% within the visible wavelength region and the optical direct band gap ($E_g$) of these films was increased with increasing post-heating temperature. A minimum resistivity of $2.5{\times}10^{-3}{\Omega}cm$ was observed at $650^{\circ}C$.

• Electrical & Electronic Materials
• /
• v.9 no.1
• /
• pp.44-50
• /
• 1996

In this study, Selenium device was fabricated by vacuum evaporation method with the substrate temperature at room temperature and its electrical and optical properties were investigated to be used in optical device. The film properties largely depended on the transmittance and annealing time, and improved with aging owing to stress release. We found that the photocurrent of the films increase linearly with light illumination. As a result, Selenium device made by this method yielded a short circuit current density of 10.5mA/$\textrm{cm}^2$, an open circuit voltage of 39OmV.

• Journal of the Optical Society of Korea
• /
• v.18 no.1
• /
• pp.82-88
• /
• 2014

A binary-coupled dipole approximation (BCDA) is described for designing metal nanoparticles with nonperiodic structures in one, two, and three dimensions. This method can be used to simulate the variation of near- and far-field properties through the interactions of metal nanoparticles. An advantage of this method is in its combination with the binary particle swarm optimization (BPSO) algorithm to find the best array of nanoparticles from all possible arrays. The BPSO algorithm has been used to design an array of plasmonic nanospheres to achieve maximum absorption, scattering, and extinction coefficient spectra. In BPSO, a swarm consists of a matrix with binary entries controlling the presence ('1') or the absence ('0') of nanospheres in the array. This approach is useful in optical applications such as solar cells, biosensors, and plasmonic nanoantennae, and optical cloaking.