• Korean Journal of Optics and Photonics
• /
• v.13 no.4
• /
• pp.295-300
• /
• 2002

We developed an optical transmitter and receiver for an electrical time division multiplexed (ETDM) 20 Gb/s optical transmission system, and experimentally investigated their characteristics. Especially, the clock extraction circuit, which is a key component in realizing broadband optical transmission receivers, was realized by using an NRZ-to-PRZ converter implemented with a half-period delay line and an EX-OR, a high-Q bandpass filter using a cylindrical dielectric resonator, and a microstrip coupled-line bandpass filter. Finally, the bit-error-rate of demultiplexed 10 Gb/s electrical signal after back to-back transmission was measured, and a high receiver sensitivity [-26.2 dBm for NRZ ($2^{7}-1$) pseudorandom binary sequence (PRBS)] was obtained

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1206-1210
• /
• 2005

This paper presents performance improvement in optical CDMA system under the presence of beat noise using a cancellation technique. Optical fibers and atmospheric optical communications have been proposed the connection between base stations and central station. The optical signal beat noise is due to interference between lightwave, many optical waves are simultaneously incident on each receiver photodiode. Since the photodiode acts as a square-law detector, beat noise can occur in the receiver. While A two-stage cancellation technique is analyzed and verified via simulation employed here because of its system simplicity. By using the random ingredients of all user signals are estimated, the beat noise is rebuilt and removed from the intended signal. In addition to cancellation technique cancel the inherent multiuser interference (MUI) in CDMA system and nonlinear distortion (NLD) in optical system. It is performed at the receiver of the central station where the random ingredients of all user signals are estimated and the MUI and the NLD are rebuilt and removed from the received signal. The validity of the cancellation technique is theoretically analyzed and shown by numerical results. The increasing of capacity in two stage cancellation are obtained.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.176-179
• /
• 1989

The optimization of the monolithic pin-FET receiver is discussed, with emphasis on the sensitivity and bandwidth. The amplifier circuit, bias resistance, total input capacitance, and transconductance of FET for the 2 Gbps transmission are calculated.

• Journal of the Optical Society of Korea
• /
• v.19 no.4
• /
• pp.334-339
• /
• 2015

Terabit-per-second (Tb/s) transmission capacity for the next generation of long-haul communication networks can be achieved using multicarrier optical super-channel technology. In an elastic orthogonal frequency division multiplexing (OFDM) super-channel transmission system, demultiplexing a portion of an entire spectrum in the form of a subband with minimum power is critically required. A major obstacle to achieving this goal is the analog-to-digital converter (ADC), which is power-hungry and extremely expensive. Without a proper ADC that can work with low power, it is unrealistic to design a 100G coherent receiver suitable for a commercially deployable optical network. Discrete Fourier transform (DFT) is often seen as a primary technique for understanding partial demultiplexing, which can be attained either optically or electronically. If fairly comparable performance can be achieved with an all-optical DFT circuit, then a solution independent of data rate and modulation format can be obtained. In this paper, we investigate two distinct OFDM super-channel receiver models, based on electronic and all-optical DFT-technologies, for partial carrier demultiplexing in a multi-Tb/s transmission system. The performance comparison of the receivers is discussed in terms of bit-error-rate (BER) performance.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.2
• /
• pp.26-38
• /
• 1994

We demonstrate a repeatless transmission of 2.5 Gbps digital signal over 98 km opticla filbers using optical transmitter and optcial receiver which are designed and implemented using commercially available devices. The optical transmitter is realized by using a distributed feedback(DFB) laser. Temperature of the laser is thermoelectrically stabilized and the output optical power is also stabilized by using negative feedback. The output power of the transmitter is 0 dBm. The optical receiver consists of an InGaAs avalanche photodiode, a preamplifier. an automatic gain control amplifier, and a clock/data regenerator. We find an optimum decision threshold that gives the best receiver sensitivity form the measured V curve. The best sensitivity is -35.5dBm( BER-1*10S010T, PRBS=2S023T -1 ) and the overload power is -9 dBm. Finally, we achieve error free optical transmission with 98 km optical fibers. The exinction ration penalty of 2 dB. the chromatic dispersion penalty of 1 dB, and the total power penalty of 3.0 dB are measured. These results satisfy CCITT recommendation.

• ETRI Journal
• /
• v.28 no.1
• /
• pp.9-16
• /
• 2006

In this paper, we analyzed and measured the electrical crosstalk characteristics of a 1.25 Gbps triplexer module for Ethernet passive optical networks to realize fiber-tothe-home services. Electrical crosstalk characteristic of the 1.25 Gbps optical triplexer module on a resistive silicon substrate should be more serious than on a dielectric substrate. Consequently, using the finite element method, we analyze the electrical crosstalk phenomena and propose a silicon substrate structure with a dummy ground line that is the simplest low-crosstalk layout configuration in the 1.25 Gbps optical triplexer module. The triplexer module consists of a laser diode as a transmitter, a digital photodetector as a digital data receiver, and an analog photodetector as a cable television signal receiver. According to IEEE 802.3ah and ITU-T G.983.3, the digital receiver and analog receiver sensitivities have to meet -24 dBm at $BER=10^{-12}$ and -7.7 dBm at 44 dB SNR. The electrical crosstalk levels have to maintain less than -86 dB from DC to 3 GHz. From analysis and measurement results, the proposed silicon substrate structure that contains the dummy line with $100\;{\mu}m$ space from the signal lines and 4 mm separations among the devices satisfies the electrical crosstalk level compared to a simple structure. This proposed structure can be easily implemented with design convenience and greatly reduce the silicon substrate size by about 50 %.

• Journal of Korea Society of Industrial Information Systems
• /
• v.11 no.3
• /
• pp.82-89
• /
• 2006

Optical transmission system related to network infra of ubiquitous is a essential bridge technique between metro network and access point. So, it is need to develop this technique. In this paper, we develop 1Gbps SNMP optical transmitter/receiver system based on 1 core ring-type WDM PON. The developed system can reduce number of optic fiber and doesn't need extra transmitter/receiver. Also, this system can extend nodes owing to many node per wavelength, acts rapidly against security cutting, and acts independent of protocols.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.13-16
• /
• 2004

The reliability of 1.550m-wavelength InGaAs mesa waveguide photodiodes(WGPDs), which developed for 40-Gbps optical receiver applications, fabricated by metal organic chemical vapor deposition is investigated. Reliability is examined by both high-temperature storage tests and the accelerated life tests by monitoring dark current and breakdown voltage. The median device lifetime and the activation energy of the degradation mechanism are computed for WGPD test structures. From the accelerated life test results, the activation energy of the degradation mechanism and median lifetime of these devices in room temperature are extracted from the log-normal failure model by using average lifetime and the standard deviation of that lifetime in each test temperature. It is found that the WGPD structure yields devices with the median lifetime of much longer than $10^6$ h at practical use conditions. Consequently, this WGPD structure has sufficient characteristics for practical 40-Gbps optical receiver modules.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.6
• /
• pp.119-124
• /
• 2008

Transimpedance amplifier(TIA) is the most significant element to determine the performance of the optical receiver, and thus the TIA must satisfy tile design requirements of high gain and wide bandwidth. In f)is paper, we propose a novel single chip optical receiver that exploits an analog adaptive equalizer and a limiting amplifier to enhance the gain and bandwidth performance, respectively. The proposed optical receiver is designed by using a $0.13{\mu}m$ CMOS process and its post-layout simulations show $120dB{\Omgea}$ transimpedance gain and 5.88GHz bandwidth. The chip core occupies the area of $0.088mm^2$, due to utilizing the negative impedance converter circuit rather than using on-chip passive inductors.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.1112-1115
• /
• 1990

Described is a new control signal transmission system which utilizes an optical fiber to transmit 2-bit control signals from the transmitter to receiver. In the transmitter the DC series control voltages are converted into the multiple frequency signals by voltage controlled oscillator (VCO). The multiple frequency signals can easily be transmitted by optical fiber. In the receiver the multiple frequency signals can be detected by analog or digital circuits and then be converted into 2-state control signals which can be used for a variety of applications.