• Korean Journal of Optics and Photonics
• /
• v.19 no.2
• /
• pp.127-131
• /
• 2008

A refractometric glucose biosensor incorporating a vertically coupled microring resonator in polymers was proposed and realized. The ring was covered with a target analyte of glucose solution with a certain concentration, so that its effective refractive index could be altered and, as a result, the resonance wavelength of the sensor was shifted. Therefore the concentration of the glucose solution can be estimated by observing the shift in the resonance wavelength. Two schemes were exploited for enhancing the sensitivity of the sensor. First, the effective refractive index of the polymeric waveguide used for the resonator sensor was adjusted to approach that of the target analyte as best as possible. Second, the ring waveguide, which serves as a crucial sensing part, was appropriately over-etched to enlarge its contact area with the analyte. The proposed resonator sensor was designed with the beam propagation method. The refractive indices of the core and cladding polymer involved were 1.430 and 1.375 respectively, leading to the waveguide's effective refractive index of ${\sim}1.390$, which is faiirly close to that of the glucose solution of ${\sim}1.333$. The prepared ring resonator with the $400-{\mu}m$ radius exhibited the free spectral range of 0.66 nm, the bandwidth of 0.15 nm, and the quality factor of 10,000. For the sensor operating at 1,550 nm wavelength, the achieved sensitivity was as great as 0.28 pm/(mg/dL), which is equivalent to 200 nm/RIU.

• Journal of the Korean Chemical Society
• /
• v.19 no.4
• /
• pp.269-279
• /
• 1975

Photosensitive properties of naphthoquinone-1,2-diazide-5-sulfonyl esters (PGND, BEND and PVAND) of polyglyceryl phthalate(PG), bisphenol A-epichlorohydrin condensate(BE) and polyvinyl alcohol(PVA) were investigated by the change of solubility before and after exposing to light. Various samples coated on glass or quartz plates were exposed to light under various conditions and steeped in aqueous alkali solution, and then the yield of residual film(W/W0) was determined. The yield of residual film, which was closely related to the sensitivity of the film, was affected by the degree of polymerization of the backbone resin, sensitizers and their concentration. In polymer homologs, the sensitivity was dependent on the degree of polymerization(the higher, the better). And also, it was most effective when 5 % of sensitizers to esters was used. The minimum exposed time was 0.6 min. for PGND-1, 1.0 min. for BEND-1, and 3.0 min. for PVAND-1. Most effective sensitizers for PGND, BEND and PVAND among those used here were benzanthrone, 5-nitroacenaphthene and picramide, respectively. The spectral sensitivities of PGND, BEND and PVAND were examined by comparing their spectrograms with UV-spectra in a solid state. Also, the sensitization and spectral sensitivity of the above polymers were studied. All the polymers containing the sensitizers showed optical sensitization. From the fact that in either case of sensitized or unsensitized sample, the ranges of absorption-maximum wave length were almost consistent with sensitivity maximum wave length, it was proved that the light absorbed by a sample served efficiently for photochemical reactions. Benzanthrone was found to be an excellent sensitizer for PGND.

• Applied Chemistry for Engineering
• /
• v.26 no.6
• /
• pp.698-705
• /
• 2015

Two series of symmetric dimesogenic compounds containing a butylene or 1-methylbutylene spacer as a flexible group were synthesized. The mesogenic groups of synthesized compounds consist of an azobenzene group with a terminal substituent. Chemical structures as well as, thermal, mesomorphic, and photochemical properties of the synthesized compounds were investigated using FT-IR, $^1H-NMR$, differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and UV-visible spectrometry. P-H, P-F, and $P-OC_6H_{13}$ showed monotropic liquid crystal phases, whereas the others showed enantiotropic liquid crystal phases. Compounds with butylene group as a flexible spacer exhibited wider mesophase temperature ranges and higher thermal transition temperatures than compounds containing a 1-methylbutylene group. Compounds with a high absolute value of the Hammett substituent constant exhibited high thermal transition temperatures and improved stability in the liquid crystal phase. Furthermore, in the absence or presence of UV light illumination, terminal substituents of the azomesogenic group were important factors in deciding the maximum absorbance wavelength (${\lambda}_{max}$) and the rate of photoisomerization (K).

• Applied Chemistry for Engineering
• /
• v.28 no.2
• /
• pp.237-244
• /
• 2017

Hyperbranched liquid crystalline polymers with azomesogenic and cholesteryl groups in their terminal positions were designed and synthesized by direct polycondensation reaction. The chemical structures and thermal and mesomorphic properties of the synthesized polymers were investigated by FT-IR, $^1H-NMR$, differential scanning calorimetry (DSC), thermogravimetry analysis (TGA), and polarizing optical microscopy (POM). The inherent viscosities (${\eta}_{inh}$) of the polymers were measured to be between 0.30 and 0.50 dL/g in phenol/p-chlorophenol/1,1,2,2-tetrachloroethane (25/40/35 = w/w/w). The degree of branching (DB) in these polymers ranged from 0.37 to 0.75; they, as amorphous polymer, showed glass transition temperatures ranging from 80 to $120^{\circ}C$; the polymers readily dissolved in most of the organic solvents used in the experiments. Only hyperbranched polymers with a cholesteryl group as their mesogenic group showed liquid crystalline phases.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.454-454
• /
• 2014

Silicon microwire array is one of the promising platforms as a means for developing highly efficient solar cells thanks to the enhanced light trapping efficiency. Among the various fabrication methods of microstructures, deep reactive ion etching (DRIE) process has been extensively used in fabrication of high aspect ratio microwire arrays. In this presentation, we show precisely controlled Si microwire arrays by tuning the DRIE process conditions. A periodic microdisk arrays were patterned on 4-inch Si wafer (p-type, $1{\sim}10{\Omega}cm$) using photolithography. After developing the pattern, 150-nm-thick Al was deposited and lifted-off to leave Al microdisk arrays on the starting Si wafer. Periodic Al microdisk arrays (diameter of $2{\mu}m$ and periodic distance of $2{\mu}m$) were used as an etch mask. A DRIE process (Tegal 200) is used for anisotropic deep silicon etching at room temperature. During the process, $SF_6$ and $C_4F_8$ gases were used for the etching and surface passivation, respectively. The length and shape of microwire arrays were controlled by etching time and $SF_6/C_4F_8$ ratio. By adjusting $SF_6/C_4F_8$ gas ratio, the shape of Si microwire can be controlled, resulting in the formation of tapered or vertical microwires. After DRIE process, the residual polymer and etching damage on the surface of the microwires were removed using piranha solution ($H_2SO_4:H_2O_2=4:1$) followed by thermal oxidation ($900^{\circ}C$, 40 min). The oxide layer formed through the thermal oxidation was etched by diluted hydrofluoric acid (1 wt% HF). The surface morphology of a Si microwire arrays was characterized by field-emission scanning electron microscopy (FE-SEM, Hitachi S-4800). Optical reflection measurements were performed over 300~1100 nm wavelengths using a UV-Vis/NIR spectrophotometer (Cary 5000, Agilent) in which a 60 mm integrating sphere (Labsphere) is equipped to account for total light (diffuse and specular) reflected from the samples. The total reflection by the microwire arrays sample was reduced from 20 % to 10 % of the incident light over the visible region when the length of the microwire was increased from $10{\mu}m$ to $30{\mu}m$.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.2
• /
• pp.137-143
• /
• 2010

Oxide semiconductors Thin-film transistors are an exemplified one owing to its excellent ambient stability and optical transparency. In particular zinc oxide (ZnO) has been reported because It has stability in air, a high electron mobility, transparency and low light sensitivity, compared to any other materials. For this reasons, ZnO TFTs have been studied actively. Furthermore, we expected that would be satisfy the demands of flexible display in new generation. In order to do that, ZnO TFTs must be fabricated that flexible substrate can sustain operating temperature. So, In this paper we have studied low-temperature process of zinc oxide(ZnO) thin-film transistors (TFTs) based on silicon nitride ($SiN_x$)/cross-linked poly-vinylphenol (C-PVP) as gate dielectric. TFTs based on oxide fabricated by Low-temperature process were similar to electrical characteristics in comparison to conventional TFTs. These results were in comparison to device with $SiN_x$/low-temperature C-PVP or $SiN_x$/conventional C-PVP. The ZnO TFTs fabricated by low-temperature process exhibited a field-effect mobility of $0.205\;cm^2/Vs$, a thresholdvoltage of 13.56 V and an on/off ratio of $5.73{\times}10^6$. As a result, We applied experimental for flexible PET substrate and showed that can be used to ZnO TFTs for flexible application.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.505-512
• /
• 2014

A new donor-accepter-donor-accepter-donor (D-A-D-A-D) type 2,1,3-benzothiadiazole-thiophene-based acceptor unit 2,5-di(4-(5-bromo-4-octylthiophen-2-yl)-2,1,3-benzothiadiazol-7-yl)thiophene ($DTBTTBr_2$) was synthesized. Copolymerized with fluorene and indeno[1,2-b]fluorene electron-rich moieties, two alternating narrow band gap (NBG) copolymers PF-DTBTT and PIF-DTBTT were prepared. And two copolymers exhibit broad and strong absorption in the range of 300-700 nm with optical band gap of about 1.75 eV. The highest occupied molecular orbital (HOMO) energy levels vary between -5.43 and -5.52 eV and the lowest unoccupied molecular orbital (LUMO) energy levels range from -3.64 to -3.77 eV. Potential applications of the copolymers as electron donor material and $PC_{71}BM$ ([6,6]-phenyl-$C_{71}$ butyric acid methyl ester) as electron acceptors were investigated for photovoltaic solar cells (PSCs). Photovoltaic performances based on the blend of PF-DTBTT/$PC_{71}BM$ (w:w; 1:2) and PIF-DTBTT/$PC_{71}BM$ (w:w; 1:2) with devices configuration as ITO/PEDOT: PSS/blend/Ca/Al, show an incident photon-to-current conversion efficiency (IPCE) of 2.34% and 2.56% with the open circuit voltage ($V_{oc}$) of 0.87 V and 0.90 V, short circuit current density ($J_{sc}$) of $6.02mA/cm^2$ and $6.12mA/cm^2$ under an AM1.5 simulator ($100mA/cm^2$). The photocurrent responses exhibit the onset wavelength extending up to 720 nm. These results indicate that the resulted narrow band gap copolymers are viable electron donor materials for polymer solar cells.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.1
• /
• pp.66-72
• /
• 2000

The behavior of nucleation and crystallization in the $Li_2O_3-SiO_2$ glass heat-treated at different condition under the conventional and microwave processing was studied by differential thermal analysis (DTA), X-ray diffractometry (XRD), optical microscopy (OM), and electrical conductivity measurement. Nucleation temperature and temperature of maximum nucleation rate in both conventionally and microwave heat-treated samples were 460~$500^{\circ}C$ and $580^{\circ}C$, respectively. It was expected that the probability for bulk crystallization increased in microwave heat-treated sample, compared to conventionally heat-treated one. Degree of crystallization increased with increasing crystallization temperature in both conventionally and microwave heat-treated samples. However, pattern of crystallization growth under microwave processing appeared to be quite different from that under the conventional one due to its internal or volumetric heating. Electrical conductivity of conventionally and microwave heat-treated samples were 1.337~2.299, 0.281~~$0.911{\times}10^{-7}\Omega {\textrm}{cm}^{-1}$, respectively.

• Journal of the Korean Chemical Society
• /
• v.61 no.6
• /
• pp.346-351
• /
• 2017

This study was planned considering the chain length, hydrophilicity, and hydrophobicity of the additives to be used in the polymerization, while various ophthalmic lenses that use various additives with similar water contents were manufactured before their optical and physical properties were compared and analyzed. With regard to the additives required for manufacturing high-, medium-, and low-water content lens groups, HEA (hydroxyethyl acrylate), PVP (polyvinylpyrrolidone), and NMV(N-methyl-N-vinylacetamide) were used as additives for preparing the high-water content lens group, HEMA(2-hydroxyethyl methacrylate), HPMA(hydroxypropyl methacrylate) and BD(1,4-butanediol) were used for the medium-water content lens group. For the low-water content lens group, BMA(buthyl methacrylate), BDDA(1,4-butanediol diacrylate), and Bis-GMA(bisphenol A glycerolate diacrylate) were used, respectively. The average water content of HEA was 40.14%; that of PVP, 39.63%; and that of NMV, 40.52%. The mean of water content was 35.92% for HEMA, 35.74% for BD, and 34.62% for HPMA. For the low-water content lens group, the mean of water content was 26.69% for BMA, 27.76% for BDDA, and 26.14% for Bis-GMA. With regard to the results of the water content measurement using a moisture analyzer, the average water content of the high-water content lens group was 41.34% for HEA, 42.62% for PVP, and 42.73% for NMV. Finally, for the low-water content lens group, the average water content was 28.62% for BMA, 28.82% for BDDA, and 28.32% for Bis-GMA. The measurements of the water contents of the lenses using the two methods showed that the water content and refractive index of the lenses were similar in all the lens groups. The measurements of the contact angles, however, showed a different wettability value for each lens with a similar water content. Also, the change tendency of the lens curvature according to the change of time showed that the change amount became larger and the recovery time became longer from the lens samples with a lower water content to those with a higher water content. Based on these results that will be helpful for the study of ophthalmic lenses.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.96-96
• /
• 2000

화학증착법으로 증착된 다이아몬드 박막은 우수한 전기적 특성과 뛰어난 화학적, 열적 안정성 때문에 전계방출소재로 많은 관심을 불러 일으키고 있다. 다이아몬드 박막의 전계방출은 저전계에서 일어나는 것으로 알려져 있으며, 저전계방출의 원인을 규명하려는 많은 연구가 진행되어 왔다. 한편, 다이아몬드 박막의 전계방출전류는 금속기판의 사용에 의한 기판/다이아몬드 접촉의 개선, 다이아몬드 박막내의 흑연성분의 조절에 의한 구조변화, 보론이나 인 (P), 질소의 도핑, 수소 플라즈마나 cesium 등의 금속을 이용한 표면처리 등의 여러 방법에 의하여 향상된다는 것이 입증되었다. 그 외에 메탄과 대기 분위기 처리, 암모니아 분위기에서의 레이저 조사도 전계방출특성을 향상시키는 것으로 보고되었다. 그러나, 다이아몬드 박막의 성장후 구조적 특성이 다른 박막의 후성장이나 열분해된 운자수소 처리가 다이아몬드 박막의 전계방출특성에 미치는 영향에 관한 연구는 지금까지 이루어지지 않았다. 본 연구에서는 수소처리와 후성장이 다이아몬드 박막의 전계방출특성에 미치는 영향을 고찰하고 이로부터 그 원인을 규명하고자 하였다. 다이아몬드 박막은 hot-filament 화학증착법을 이용하여 증착하였다. 후성장한 다잉아몬드 박막내의 흑연성분과 박막의 두께를 체계적으로 조절하여 후성장 박막의 구조적 특성과 그 두께의 영향을 확인할 수 있었다. 후성장층내의 흑연성분과 두께가 증가할수록 전계방출특성은 향상되다가 저하되었다. 한편, 다이아몬드 박막을 성장시킨 후 수소분위기 처리를 함에 따라 전계방출특성은 향상되었지만 수소처리시간이 5분 이상으로 증가함에 따라 그 특성은 저하되었다. 본 연구에서는 수소처리와 후성장시 나타나는 전계방출특성의 변화 원인을 규명하고자 한다.기판위에서 polymer-like Carbon 구조는 향상되는 경향을 보였다.0 mm인 백금 망을 마스크로 사용하여 실제 3차원 미세구조를 제작하여 보았다. 그림 1에서 제작된 구조물의 SEM 사진을 보여주었으며, 식각된 면의 조도가 매우 뛰어나며 모서리의 직각성도 우수함을 확인할 수 있다. 이와 같이 도출된 시험 조건을 기초로 하여 리소그래피 후에 전기 도금을 이용한 금속 몰드 제작 및 이온빔 리소그래피 장점을 최대한 살릴수 있는 미세구조 제작에 대한 연구를 계속 추진할 계획이다. 비정질 Si1-xCx 박막을 증착하여 특성을 분석한 결과 성장된 박막의 성장률은 Carbonfid의 증가에 따라 다른 성장특성을 보였고, Silcne(SiH4) 가스량의 감소와 함께 박막의 성장률이 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 줄어들어 성장률이 Silane가스량에 의해 지배됨을 볼 수 있다. UV-VIS spectrophotometer에 의한 비정질 SiC 박막의 투과도와 파장과의 관계에 있어 유리를 기판으로 사용했으므로 유리의투과도를 감안했으며, 유리에 대한 상대적인 비율 관계로 투과도를 나타냈었다. 또한 비저질 SiC 박막의 흡수계수는 Ellipsometry에 의해 측정된 Δ과 Ψ값을 이용하여 시뮬레이션한 결과로 비정질 SiC 박막의 두께를 이용하여 구하였다. 또한 Tauc Plot을 통해 박막의 optical band gap을 2.6~3.7eV로 조절할 수 있었다. 20$0^{\circ}C$이상으로 증가시켜도 광투과율은 큰 변화를 나타내지 않았다.부터