• Korean Journal of Materials Research
• /
• v.5 no.1
• /
• pp.96-103
• /
• 1995

This art~cle reports on the formation of T - Gate with O.1$\mu$m foot and 0.4$\mu$m head width at PMMA/P( MMA/MAA) resist structure using a 30KV electron beam lithography system. From the result of Monte Carlo simulation on PMMA/P( MMA/MAA)/GaAs, we obtain the dissipation energy ratio of forwardscattered electron and backscattered electron within 0.1$\mu$m scattering radius is 19.5 : 1 0.1$\mu$m T - gate has been formed with 30KV gaussian electron beam at a 440$\mu C/\textrm{cm}^2$ dosage. The gamma value of PMMA and P(MMA/MAA) at MIBK : IPA=l : 1 developer was 2.3. The overlay accuracy(3$\sigma$) from mix-andmatch of optical stepper and Ekeam lithography system for fabricating HEMT device is accomplished below 0.1$\mu$m.

• Journal of Biosystems Engineering
• /
• v.41 no.4
• /
• pp.408-417
• /
• 2016

Purpose: Yield monitoring systems are an essential component of precision agriculture. They indicate the spatial variability of crop yield in fields, and have become an important factor in modern harvesters. The objective of this paper was to review research trends related to yield monitoring sensors for grain crops. Methods: The literature was reviewed for research on the major sensing components of grain yield monitoring systems. These major components included grain flow sensors, moisture content sensors, and cutting width sensors. Sensors were classified by sensing principle and type, and their performance was also reviewed. Results: The main targeted harvesting grain crops were rice, wheat, corn, barley, and grain sorghum. Grain flow sensors were classified into mass flow and volume flow methods. Mass flow sensors were mounted primarily at the clean grain elevator head or under the grain tank, and volume flow sensors were mounted at the head or in the middle of the elevator. Mass flow methods used weighing, force impact, and radiometric approaches, some of which resulted in measurement error levels lower than 5% ($R^2=0.99$). Volume flow methods included paddle wheel type and optical type, and in the best cases produced error levels lower than 3%. Grain moisture content sensing was in many cases achieved using capacitive modules. In some cases, errors were lower than 1%. Cutting width was measured by ultrasonic distance sensors mounted at both sides of the header dividers, and the errors were in some cases lower than 5%. Conclusions: The design and fabrication of an integrated yield monitoring system for a target crop would be affected by the selection of a sensing approach, as well as the layout and mounting of the sensors. For accurate estimation of yield, signal processing and correction measures should be also implemented.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.6 no.4
• /
• pp.31-40
• /
• 2016

Recently, technology of Virtual Reality(VR) based on HMD among various kinds of VR implemented products has received widespread attention. Major IT-related companies around the world participated in VR HMD research and development. Therefore, the possibility of the spread of VR HMD has been highly praised. Demands of VR HMD products using Smart Phone has been especially increased so that it is required to create a high quality of VR contents. The purpose of study in this paper is to apply the depth value of stereoscopic to VR HMD. To implement it, we analyzed VR HMD optical system and converted an experimental image to virtual depth caused by binocular disparity based on the result of calculating NPP(Native Pixel Parallax). We produced the image of stereoscopic applied with the value converted and applied to VR HMD. This study is expected to be utilized as a VR content creation field of quantitative data.

• Korean Journal of Optics and Photonics
• /
• v.8 no.4
• /
• pp.333-339
• /
• 1997

We fabricated a sensor head which consists of spliced different-diameter fiber gratings for discrimination between strain and temperature. Because the fibers were drawn from the same preform, their temperature characteristics were the same but not for strain sensitivities which are inversely proportional to fibers cross-sectional areas. In measurement range of 0-1500$\mu$strain and 20-10$0^{\circ}C$, we could obtain, by using the matrix calculation, the unknown physical quantities within 10% of calculation error compared with the micrometer and thermocouple values. To improve the strain measurement accuracy, we suggest a new, novel method which deploys an unbalanced fiber Mach-Zehnder interferometer. This new signal processing technique converts the strain information to interference signal amplitude variation, temperature-independently. we obtained measurement accuracy nearly 80 times better than that obtainable with the conventional optical spectrum analyzer usage.

• Fire Science and Engineering
• /
• v.30 no.1
• /
• pp.37-42
• /
• 2016

The dimensionless extinction constants of smoke particles produced from burning of soy methyl ester (B100) biodiesel and ultra low sulfur diesel (ULSD) fuels were measured. To this end, optical measurements of smoke volume fraction with the aid of a He-Ne laser at 633 nm were compared to the simultaneous gravimetric measurements. The average value of measured dimensionless extinction constants at 633 nm was 11.8 for biodiesel smoke particles and 11.1 for diesel smoke particles, respectively whose values are very comparable withing the range of measurement uncertainty (${\pm}10.1%$). The analysis of Raman spectroscopy revealed that overall characteristics of light extinction between particles produced from each fuel may differ from each other.

• Journal of Sensor Science and Technology
• /
• v.23 no.2
• /
• pp.110-113
• /
• 2014

In this paper, we propose and demonstrate a Fabry-Perot interferometer (FPI) optical fiber tip sensor fabricated by a blade-sawing technique using a fiber optic patch cord for high-resolution temperature measurement. The sensor head consists of a short air FP cavity near the tip of a single-mode fiber patch cord tip. The temperature which we can measure is determined through a phase variation of the interference fringes in the reflective spectrum of the sensor. The fiber optic FPI sensor in this work can monitor the environmental temperature very accurately from 40 to $120^{\circ}C$. As a result, the temperature sensitivity is obtained as $38.2pm/^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.11
• /
• pp.3307-3311
• /
• 2013

A new fiber optical sensor was developed for the determination of 2,4-dichlorophenol (DCP). The sensor was based on DCP oxidation by oxygen with the catalysis of iron(III) tetrasulfophthalocyanine (Fe(III)PcTs). The optical oxygen sensing film with $Ru(bpy)_3Cl_2$ as the fluorescence indicator was used to determine the consumption of oxygen in solution. A lock-in amplifier was used for detecting the lifetime of the oxygen sensing film by measuring the phase delay change of the sensor head. The different variables affecting the sensor performance were evaluated and optimized. Under the optimal conditions (i.e. pH 6.0, $25^{\circ}C$, Fe(III)PcTs concentration of 0.62 mg/mL), the linear detection range and response time of the sensor are $1.0{\times}10^{-6}-9.0{\times}10^{-6}$ mol/L and 250 s, respectively. The sensor displays high selectivity, good repeatability and stability, and can be used as an effective tool in analyzing DCP concentration in practical samples.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.4
• /
• pp.321-327
• /
• 2015

In this paper, we propose an algorithm for achieving robust Visual Voice Activity Detection (VVAD) for enhanced speech recognition. In conventional VVAD algorithms, the motion of lip region is found by applying an optical flow or Chaos inspired measures for detecting visual speech frames. The optical flow-based VVAD is difficult to be adopted to driving scenarios due to its computational complexity. While invariant to illumination changes, Chaos theory based VVAD method is sensitive to motion translations caused by driver's head movements. The proposed Local Variance Histogram (LVH) is robust to the pixel intensity changes from both illumination change and translation change. Hence, for improved performance in environmental changes, we adopt the novel threshold estimation using total variance change. In the experimental results, the proposed VVAD algorithm achieves robustness in various driving situations.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.44 no.4
• /
• pp.128-135
• /
• 2021

WDM(Wavelength Division Multiplexing) is called a wavelength division multiplexing optical transmission method and is a next-generation optical transmission technology. Case company F has recently developed and sold PLC(Planar Lightwave Circuit), a key element necessary for WDM system production. Although Chinese processing companies are being used as a global outsourcing strategy to increase price competitiveness by lowering manufacturing unit prices, the average defect rate of products manufactured by Chinese processing companies is more than 50%, causing many problems. However, Chinese processing companies are trying to avoid responsibility, saying that the cause of the defect is the defective PLC Wafer provided by Company F. Therefore, in this study, the responsibility of the PLC defect is clearly identified through estimating the defect rate of PLC using the sampling inspection method, and the improvement plan for each cause of the PLC defect for PLC yeild improvement is proposed. The result of this research will greatly contribute to eliminating the controversy over providing the cause of defects between global outsourcing companies and the head office. In addition, it is expected to form a partnership with Company F and a Chinese processing company, which will serve as a cornerstone for successful global outsourcing. In the future, it is necessary to increase the reliability of the PLC yield calculation by extracting more precisely the number of defects.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.12
• /
• pp.161-168
• /
• 2016

Thanks to mass production and provision of smartphones and the HMD (head mounted display), VR (virtual reality) is now being applied to various areas. The VR HMD is the interface equipment which allows users to have realistic experiences through human sensory organs such as vision and auditory sense. Since the majority of VR equipment is operated by the display for both eyes, 360-degree video content and the depth information, the VR mechanism is closely related to human senses, especially vision. Previous studies have focused on how to minimize negative impact such as motion sickness or visual fatigue. Little attention has been paid on research about the visual treatment. Therefore, the focus of this study is to develop technical elements for utilization of vision therapy with the VR HMD and explore possible areas to apply it. To this end, we analyzed the past case studies and technical elements to identify 16 areas for vision therapy. We also developed the optical parameters for utilization of the VR HMD visual targets. The result of this study is expected to be utilized for development of visual targets for vision therapy based on the VR HMD.