• Journal of Power Electronics
• /
• v.10 no.1
• /
• pp.21-26
• /
• 2010

The most important feature of the one-cycle control method is its excellent ability in line disturbance rejection. However, when it is used as a controller in dc-dc converters, it has an undesirable transient response. The voltage overshoot at the transient time, which usually exists in one-cycle controlled converters, is unwanted in many applications and it is sometimes hazardous. In this paper, it is shown that the combination of a one-cycle controller with a current mode controller, can improve the transient response and consequently the overshoot can be controlled. Therefore, the combined controller has the excellent line disturbance rejection of a one-cycle controller and the output current limiting capability of current mode controllers. Because in this scheme a one-cycle controller is the master controller, the problem of instability of current mode control, will not happen. By simulation and a practical prototype, the capability of the method is shown.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.443-454
• /
• 2015

This study proposes a novel one-cycle control scheme with a plug-in repetitive controller for load compensator. The novelty of this scheme lies in the combination of high dynamics and the simplicity of a one-cycle controller and good steady-state harmonic suppression ability of the repetitive controller. In addition, the proposed scheme can reduce the effect of the harmonics in phase voltage for the existence of the repetitive controller. Finally, experimental results on a three-phase, four-wire, three-level load compensator are reported to validate the effectiveness of the proposed control scheme.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1592-1598
• /
• 2008

Fixed cycle traffic signal controller is pattern type controller. This method is that one concluding traffic proposal affect fixed cycle controller to deciding cycle time during 24 hours. Traffic intersection jam is caused traffic controller supervisor input wrong traffic proposal. The available to traffic controller is traffic proposal is not selected by an outward look but propriety traffic proposal is compared with each other. This paper presents that property traffic proposal adopted to fixed cycle controller by fuzzy analytic hierachy process and new proposal adopted fixed cycle controller is compared with others.

• Journal of Power Electronics
• /
• v.12 no.3
• /
• pp.410-417
• /
• 2012

In this paper, a direct current control method based on a one-cycle controller (DCOCC) for double frequency buck converters (DF buck) is proposed. This control method can make the average current through the high frequency and low frequency inductors of a DF buck converter equal. This is similar to the average current control method. However, the design of the loop compensator is much easier when compared with the average current control. Since the average current though the high frequency and low frequency inductors is equivalent, the current stress of the high frequency switches and the switch losses are minimized. Therefore, the efficiency of the DF buck converter is improved. Firstly, the operation principle of DCOCC is described, then the small signal models of a one cycle controller and a DF buck converter are presented based on the state space average method. Eventually, a system block diagram of the DCOCC controlled DF buck is established and the compensator is designed. Finally, simulation and experiment results are given to verify the correction of the theory analysis.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.311-314
• /
• 1999

This paper presents the design method of a repetitive controller to educe the harmonics in the output voltage waveform of the AC power supply systems. Output voltage error under the nonlinear load like a rectifier is cyclic with the same period to fundamental wave, therefore one can design the repetitive controller calculating cycle by cycle. The controller is verified mathematically and by simulations.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.89-95
• /
• 2000

The engine idle speed mode becomes worse as one drives a vehicle for several years. This is due to ageing of engine and power-train parts. In this case, unstable idle conditions such as engine stall and droop are frequently experienced when the engine gets heavy torque loads due to power steering pump and air conditioning compressor. The objective of this paper is to study on the idle speed control using PID controller under load disturbances. The input of the PID controller is an error of rpm. The output of the PID controller is an ISCV duty cycle. The dSPACE Controller Boards are used to interface with engine. The on-vehicle test is realized using by SIMULINK and BLOCKSETS tools. The real time interface control panel supplied by Control Desk S/W is designed to have good results in engine idle speed control.

• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.778-787
• /
• 2014

This study presents an input filter resonance mitigation method for an AC-DC matrix converter. This method combines the advantages of the one-cycle control strategy and the active damping technique. Unnecessary sensors are removed, and system cost is reduced by employing the grid-side input currents as feedback to damp out LC resonance. A model that includes the proposed method and the input filter is established with consideration of the delay caused by the actual controller. A zero-pole map is employed to analyze model stability and to investigate virtual resistor parameter design principles. Based on a double closed-loop control scheme, the one-cycle control strategy does not require any complex modulation index control. Thus, this strategy can be more easily implemented than traditional space vector-based methods. Experimental results demonstrate the veracity of theoretical analysis and the feasibility of the proposed approach.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.95-99
• /
• 2000

New locking algorithm of DLL is proposed to improve the locking speed and low power dissipation in this paper, In spite of using the architecture of delay controller, low power consumption is acquired by operating only one controller at once and fast locking speed is accomplished by initial setting from the coarse controller. The proposed DLL circuit is operated from 50MHz to 200MHz and locked within 6 cycle at all of operating frequency.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.1060-1066
• /
• 1992

One of the undesirable nonlinear phenomenon called 'wind up' occours when the integrator in the controller and the saturated actuator interact. Large overshoot, slow response, instability, limit cycle and jump resonance are the characteristics of wind up phenomenon. Several 'anti-windup' compensators have been developed to prevent some of the aforementioned nonlinear characteristics such as instabilituy and limit cycle, but none has studied the effect of antiwindup compensator on the jump resonance. In this paper, we developed an analyitcal method to design the compensator to prevent not only limit cycle but also jump resonance. An illustrative example is included to show the compensator eliminates jump resonance of effectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.5
• /
• pp.1117-1125
• /
• 2000

A current mode PWM method applied one cycle response to averaging circuit model Buck converters is presented. The controller nonlinear PWM implement is based on the error between the switched variable and the response reference to zero each cycle. As the result, the system transfer function is derived as a function of the desired close loop poles, simplifying the design procedure and bringing forward all the important characteristics of the close loop system. The proposed controller has significant advantages over conventional current mode control methods in noise susceptibility, dynamic response and without inductor current sensing, Finally, the simulation and experiment results confirm the proposed PWM control techniques.