• Journal of the Korean Wood Science and Technology
• /
• 제40권5호
• /
• pp.343-351
• /
• 2012

A large diameter roundwood is an important element of Korean traditional buildings, Hanok, and is hard to be dried without surface cracks. Four different pretreatments, such as pre-cracking, oil heating, kerfing-oil heating and PEG impregnation, were investigated for reducing the surface cracks of large-diameter roundwood specimens during heat treatment. The roundwood specimens of pre-cracking, oil heating and kerfing-oil heating showed surface cracks during pretreatment, but that of PEG impregnation did not. It was confirmed that kerfing reduced the total crack width. Among the four pretreatments and control only the PEG impregnation roundwood specimen had no crack on both outer and inner surfaces after heat treatment. The PEG impregnation specimen shrank only 1.6% in the tangential direction while the pre-cracking did 8.0%.

• 한국표면공학회지
• /
• 제53권6호
• /
• pp.300-305
• /
• 2020

Corrosion of reinforcement steel rebar is a serious problem in a wide range of concrete application for buildings and infrastructures. Hydrophobizing surface treatments, such as self-assembled monolayer coating, edible oil-impregnation and silicone oil-impregnation were applied to solidified concrete. The hydrophobizing of concrete significantly reduces an absorption and transportation of water toward a steel rebar in concrete, so that the corrosion resistance of the steel rebar. In particular, the silicone oil-impregnation not only forms the hydrophobic monolayer on the concrete but also fills the inter-connected pores of concrete, thus the corrosion of steel rebar is significantly inhibited compared to the self-assembled monolayer coating and edible oil-impregnation. Therefore, the silicone oil-impregnation can be a promising candidate for preventing corrosion of steel rebar in concrete for durable performance and safety.

• 한국정밀공학회지
• /
• 제19권3호
• /
• pp.114-122
• /
• 2002

Electric conductivities, mechanical properties and friction properties were investigated far graphite-nylon composites impregnated with oil. Specific resistivity of composites containing oil from 2% to 6% were in the range of $10^7 ~10^6 \ohm$ cm, which were applicable for anti-static purpose of composites improved by the impregnation of graphite with 2%. Improvement in the impact strength and friction properties of graphite/nylon composites was achieved by the impregnation of oil. The coefficient of friction of the composites containing graphite from 2% to 4% and oil with 2 - 4% showed much loller than that of virgin nylon. Also the abrasive wear of the oil impregnated graphite composites were decreased about 1/3 - 1/10.

• Journal of the Korean Wood Science and Technology
• /
• 제49권6호
• /
• pp.602-615
• /
• 2021

Red jabon wood is a potential fast-growing species for veneer, furniture, and many other wood products, but its durability is very low. The purpose of this study was to investigate the effects of castor bean oil and heating on boron leaching, dimensional stability, and resistance to decay fungi in treated jabon wood. Red jabon wood was preserved with boron solutions containing 5% boron (boric acid, borax, or borax-boric acid). Following that, castor bean oil impregnation and heating were used as posttreatments. Furthermore, all the wood samples were tested in terms of leaching, dimensional stability, and resistance against Schizophyllum commune and Fomitopsis palustris fungi. This study discovered that boron compounds, castor bean oil, and heating treatments influenced the leaching, dimensional stability, and resistance of red jabon wood to decay fungi. The double impregnation of boric acid or borax and castor bean oil, followed by heating at 160℃, significantly reduced water absorption and leaching while increasing the dimensional stability and resistance of red jabon wood against the two tested decay fungi.

• Advances in nano research
• /
• 제12권6호
• /
• pp.629-638
• /
• 2022

This work shows the impregnation of scents using a graphene sponge (GS). This was functionalized by the modified Hummers method, pursuing to add different functional groups. It is proposed to achieve the release and seek to control it through electrical potential applied to the graphene sponge with essential oils. The graphene sponge was functionalized and steeped with two kinds of oil. The electrochemical study demonstrates the variation in the electrochemical behaviour of the functionalized graphene sponge without and impregnated with oil. The release of the oil and its aromatic scents was carried out by applying an electrical potential of 30 V, with a release rate of 1.86 mg/min. The heating of the sample that causes the release of oil, associated with the electrical resistance of the system, reaches temperatures of about 150℃. The essential oils, graphene sponge, surfactant, graphene sponge with essential oils, graphene sponge recuperated after applying electric potential, graphene sponge recovered by temperature and dipropylene glycol (DPG) were characterized using Fourier transformed infrared spectroscopy (FTIR), digital microscopy, and x-ray photoelectron spectroscopy (XPS).

• Journal of the Korean Wood Science and Technology
• /
• 제44권6호
• /
• pp.842-851
• /
• 2016

The objective of this study was to improve physical and mechanical properties of soft-inner part of oil palm trunk (S-OPT) after impregnation with phenol formaldehyde (PF) resin and densification by close system compression (CSC) method. Effect of different methods of PF resin impregnation (i.e., no vacuum-pressure, vacuum, and vacuum-pressure) was evaluated. The results showed that PF resin impregnation and CSC significantly improved the physical and mechanical properties of S-OPT up to: (1) 176% in density; (2) 309% in modulus of rupture (MOR); (3) 287% modulus of elasticity (MOE); and (4) 191% in the compressive strength. Physical and mechanical properties of S-OPT showed their best performances when PF resin impregnated with vacuum-pressure method as shown by higher weight gain, density, MOR, MOE, compressive strength, and lower recovery of set due to better penetration of PF resin into S-OPT. Combining PF resin impregnation and densification by CSC method could be a good method to improve physical and mechanical properties of S-OPT.

• 한국표면공학회지
• /
• 제54권2호
• /
• pp.90-95
• /
• 2021

Surface modification technique enabling the control of condensation provides various benefit in various engineering systems, such as heat transfer, desalination, power plants, and so on. In this study, lubricant oil-impregnation into Teflon-coated nanoporous anodic oxide layer of aluminum to enhance a de-wetting and mobility of water droplet on surface. Due to the surface treatment improving water-repellency, the condensation mode is changed to dropwise, thus the frequency of sliding condensed water droplet on surface is increased. For these reasons, the surface of oil-impregnated Teflon-coated nanoporous anodic aluminum oxide shows significantly enhanced condensation heat transfer compared to bare aluminum surface. In addition, the porosity of anodic aluminum oxide affected the mobility of water droplet even with oil-impregnation and Teflon-coating, indicating that the optimization of porous structure of anodic oxide is required for maximizing the condensation heat transfer.

• 한국가구학회지
• /
• 제19권1호
• /
• pp.91-96
• /
• 2008

This paper investigates the penetration of essential oil into radial and longitudinal directions of Castanea crenata. Present study was performed to know the essential oil penetration depth in radial and longitudinal direction of Castanea crenata. Essential oil penetration depth was found higher in longitudinal direction than in radial direction and it was about 53 times high at 15.0 second of penetration. In early wood, fiber conducted oil more than that of large vessel. In heartwood, fiber had played an important role for the conduction of oil. But in sapwood, small vessel conducted oil deeper than wood fiber, which was also significantly different from large. On the other hand, large vessel in heartwood had statistically lower penetration depth than that of fiber and small vessel. At the beginning of penetration the speed was high and gradually decreased in course of time.

• 동력기계공학회지
• /
• 제14권4호
• /
• pp.50-55
• /
• 2010

In order to investigate tribological effects of nano copper particles impregnated(CuN) on surface polytetrafluoroethylene(PTFE) on sealing wear and an experimental study was carried out to determine the wear behavior of copper nano-particles impregnation two kind thickness in super critical $CO_2$ liquid. Experimental results showed that the friction coefficients of CuN PTFE at the low sliding speed(0.44m/s) and the oil temperature ($60^{\circ}C$) were higher than that of virgin PTFE. And a thin nano copper particles impreganated thickness was formed on the surface in the PTFE and the specimen with this treatment has much better friction properties than the original one. Fortunately, at the high load(80 N) and the oil temperature, the friction coefficient of CuN PTFE was lower than that of virgin PTFE. This evidenced the load carrying capacity of CuN PTFE was much better than that of virgin PTFE under the high load condition(80 N) specially. Therefore, it can be concluded that the friction coefficient variation of CuN PTFE is very small but its wear rate decreases greatly with increase in sliding speed.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.142-149
• /
• 2002

The frictional properties of nylon can be improved by the impregnation of lubricants like wax, oil or graphite. The inclusion of these lubricants, on the other hand, decreases the mechanical properties of nylon, such as tensile strength, hardness and impact strength. As an attempt to maximize frictional properties, while minimizing a decrease in the mechanical properties, various kinds of nylon containing 3 wt% wax and varying contents of oil or graphite were prepared. It was found that the synergy effects to improve both friction and anti-wear properties is evidenced by impregnating a combination of wax/oil or wax/graphite. The wear rate of a nylon containing 3 wt% of wax and 1.5 wt% of oil turned out to be 1/4 of that of nylon impregnated with 8 wt% wax or 8 wt% oil. The latter showed the lowest wear rate among the nylons prepared with a single lubricant. In addition, the friction coefficient of the developed nylon was found to be very similar to the nylon with 8 wt% wax only.