• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.72-80
• /
• 2013

For the proper cooling of in-wheel motor, the cooling channel should have the characteristics which are low pressure drop and adequate cooling oil supply to motor part. In this study, the flow performance of cooling channel for in-wheel motor was evaluated and the shape of the channel was optimized. First, the pressure drop and flow distribution characteristics of the initial channel model were evaluated using numerical analysis. Also, by the result of analysis and design modification, 4 design parameters of the channel were selected. Second, using the Taguchi optimal method, the cooling channel was optimized. In the method, nine models with different levels of the design parameters were generated and the flow characteristics of each models was estimated. Base on the result, the main effect of the design parameters was founded and optimized model was obtained. For the optimized model, the pressure drop and oil flow rate were about 0.196 bar and 0.207 L/min, respectively. The pressure drop decreased by about 0.3 bar and the oil flow rate to the motor part increased by about 0.2 L/min compared to the initial model.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.2129-2134
• /
• 2004

The present study has been conducted to develop a heat pump system using river water of temperature energy which not only belongs to unutilized energy but is a kind of good heat source due to maintain its temperature in a certain degree regardless of seasonal variation. The system did not meet the proposed performance after setup. In this paper, the system performance affected by refrigerant Oil, by pressure drop, or by other factors has been discussed. The followings were obtained : (1) Refrigerant Oil mixture rate was 2.5 in weight percentage, (2) Pressure drop through evaporator was 29.1kPa($3.1^{\circ}C$ in saturated tempearture) (3) Pressure drop from the end of evaporator to compressor inlet was 39.8kPa($4.0^{\circ}C$ in saturated tempearture). (4) The system performance can to be improved by modifying a part of pipe line to compressor, and reducing pressure drop through heat exchangers.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.359-360
• /
• 2002

A methodology was developed for evaluation of oxidation stability of base stocks and engine oils. Analytical procedures for both classes of lubricants were based on the ASTM standards D 6186 and/or E 2009. The procedures were applied to a set of engine oils of the SAE 5W-30 specification, and to a set of several hydrocracked and solvent neutral base oils, both with and without addition of antioxidant. A potential of a pressure DSC for diagnostic purposed was also demonstrated by monitoring the engine oil ageing during its operation in heavy-duty engine.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.102-107
• /
• 2001

Recently, with the increasing of construction works, large construction equipment are used to reduce the term of work and labor cost in construction field. Therefore, construction equipment noise has caused much annoyance for a number of dweller in nearby construction field and it has become a very serious problem in our living environment. Neverthless, in our country, adequite guidelines for the construction equipment noise are very deficiency because of the lack of basic data and insufficient research works. From this point of view, this study attempts to survey the characteristics and prediction of piling noise in oil pressure method. On the basis of measurement value, we analysed about prediction possibility of piling noise in oil pressure method.

• 동력기계공학회지
• /
• 제6권2호
• /
• pp.82-87
• /
• 2002

For the dynamic behavior evaluation of a semi-active vibration control system, it is very important to use an accurate mathematical model for the hydraulic damper applied to the control system. In this study, a mathematical model for a symmetric type hydraulic damper was suggested. In this model, the effects of gas volume and oil temperature variation on the bulk modulus of oil were considered. The dynamic behavior of the damper was investigated by experiments and simulations. It was confirmed that the pressure variation, damping force, and mean pressure variation could be estimated with comparatively good precision by the suggested mathematical model. Moreover, it was shown that excessive pressure rise can be generated by the oil expansion due to the heat energy transformed from the exciting energy of the damper for a short period of the damper operation.

• 동력기계공학회지
• /
• 제2권1호
• /
• pp.45-51
• /
• 1998

An analyzing method for pressure fluctuations in oil hydraulic pipe network was developed in this study. The object pipe network has multi-branch configuration, and the pipelines of it are composed of metal tubes and flexible hoses. Transfer matrix method, in other words impedance method, was used for the analysis. Values of physical parameters describing the characteristics of flexible hose were measured by experiments and reflected to the analysing procedure. The reliability and usefulness of the analyzing method were confirmed by investigating computed results and experimental results got in this study.

• Membrane and Water Treatment
• /
• 제1권4호
• /
• pp.297-316
• /
• 2010

Membrane fouling is one of the major operational concerns of membrane processes which results in loss of productivity. This paper investigates the ultrafiltration (UF) results of synthetic oil-in-water (o/w) emulsion using flat sheets of polysulfone (PSf) membrane synthesized with four different compositions. The aim is to identify the mechanisms responsible for the observed permeate flux reduction with time for different PSf membranes. The experiments were carried out at four transmembrane pressures i.e., 68.9 kPa, 103.4 kPa, 137.9 kPa and 172.4 kPa. Three initial oil concentrations i.e., 75 $mgL^{-1}$, 100 $mgL^{-1}$ and 200 $mgL^{-1}$ were considered. The resistance-in-series (RIS) model was applied to interpret the data and on that basis, the individual resistances were evaluated. The significances of these resistances were studied in relation to parameters, namely, transmembrane pressure and initial oil concentration. The total resistance to permeate flow is found to increase with increase in both transmembrane pressure and initial oil concentration while for higher oil concentration, resistance due to concentration polarization is found to be the prevailing resistance. The applicability of the constant pressure filtration models to the experimental data was also tested to explain the blocking process. The study shows that intermediate pore blocking is the dominant mechanism at the initial period of UF while in the later period, the fouling process is found to approach cake filtration like mechanism. However, the duration of pore blocking mechanism is different for different membranes depending on their morphological and permeation properties.

• 한국산업융합학회 논문집
• /
• 제5권2호
• /
• pp.119-126
• /
• 2002

In this study, general engine oil and the Miracle top engine oil of Dongjin chemistry company were tested to find the effects to the SI engine performance. Roller dynamometer used to find maximum power, fuel consumption rate and the emission. Maximum power was measured higher when the Miracle top engine oil was used in the vehicle. By use of the Miracle top engine oil, fuel consumption rate and emission was measured lower and compression pressure was higher compared use of general engine oil. Also the Miracle top engine oil was found to decrease the engine noise at the low RPM. And after 1,500km drive at the same condition, the dust in the oil pan and oil filter was measured less when the Miracle top engine oil used compared than general engine oil used.

• 대한기계학회논문집B
• /
• 제24권7호
• /
• pp.938-944
• /
• 2000

Recently, micro fin tube is widely used to heat exchanger for high performance. And, as the alternative refrigerants for R-22, hydrocarbons such as R-290, R-600 and R-600a are very promising because of their low GWP and ODP. Thus, R-290 was used as working fluid in this study. Most design of heat exchanger had been based on heat transfer characteristics of pure refrigerant although refrigerant oil exists in the refrigeration cycles. So, the influence of oil on heat transfer characteristics have to be considered for investigating exact evaporation heat transfer characteristics. But, this is an unresolved problem of refrigeration heat transfer. Therefore the influence of the refrigeration oil to the evaporation heat transfer characteristics of R-290 were conducted in a horizontal micro tin tube. The mineral oil was used as refrigeration oil. The experimental apparatus consisted of a basic refrigeration cycle and a system for oil concentration measurement. Test conditions are as the follows; evaporation temperature $5^{\circ}C$, mass velocity 100 $kg/m^2s$, heat flux 10 $kW/m^2$, oil concentration 0, 1.3, 3.3, 5.7 wt.%, and quality $0.07{\sim}1.0$. When refrigeration oil was entered, oil foaming was observed at the low quality region. And, very small bubbles were observed as quality was increased. Pressure drop and heat transfer coefficient increased as the concentration of refrigeration oil increased to 5 wt.%.. The performance index of heat exchanger was the highest near 3.3 wt.%.

• 대한토목학회논문집
• /
• 제44권3호
• /
• pp.271-276
• /
• 2024

고갈되고 있는 자원인 전통 석유는 전세계 석유매장량의 3분의 1에 불과하여 비전통 오일을 자원으로 활용하고자 하는 연구와 사례가 지속적으로 증가하고 있다. 하지만 비전통 오일에는 모래와 같은 고체입자가 포함된 역청이 함유되어 있으며 고온 고압의 환경에 노출되기 때문에 송유관에 변형이 빈번히 발생할 수 있다. 따라서 송유관의 변형에 영향을 끼칠 수 있는 재료, 두께, 각도 등의 변수를 도출하여 송유관에 적용하고 Ansys 프로그램을 통해 유한요소해석을 진행하였다. 유한요소해석의 결과로 변형, 최대하중 용량을 도출하였다. 이후 변형 저항과 최대하중 용량이 가장 우수한 인자를 조합하여 최적화된 송유관을 모델링하여 동일한 해석을 진행하였다. 해석 결과 변형을 감소시키며 30 % 가량 최대하중 용량을 증진시키는 효과를 확인하였고 송유관 해석 시 변형억제를 위한 인자들을 도출하였다.