• Journal of Astronomy and Space Sciences
• /
• v.10 no.2
• /
• pp.189-196
• /
• 1993

Satellite laser ranging observation of LAGEOS II has been performed using the SLR System at Sheshan Laser Ranging Station, Shanghai Observatory. And we obtained 1,838 observational points. The observed range data is corrected by means of system delay correction using ground target observation, atmospheric refraction delay correction, offset correction, general relativistic correction and tide correction including solid tide, polar tide and ocean tide. As a result, the determined range delay mean value is 19.12m and the mean internal accuracy by means of polynomial fitting and least square method is $\pm$7cm. Corrected observational points are 1,340 and noise ratio to total observational points is 27.1%.

• Korean Journal of Materials Research
• /
• v.29 no.12
• /
• pp.764-773
• /
• 2019

The gas response characteristic toward C₂H₅OH has been demonstrated in terms of copper-vacancy concentration, hole density, and microstructural factors for undoped/Li(I)-doped CuO thin films prepared by sol-gel method. For the films, both concentrations of intrinsic copper vacancies and electronic holes decrease with increasing calcination temperature from 400 to 500 to 600 ℃. Li(I) doping into CuO leads to the reduction of copper-vacancy concentration and the enhancement of hole density. The increase of calcination temperature or Li(I) doping concentration in the film increases both optical band gap energy and Cu2p binding energy, which are characterized by UV-vis-NIR and X-ray photoelectron spectroscopy, respectively. The overall hole density of the film is determined by the offset effect of intrinsic and extrinsic hole densities, which depend on the calcination temperature and the Li(I) doping amount, respectively. The apparent resistance of the film is determined by the concentration of the structural defects such as copper vacancies, Li(I) dopants, and grain boundaries, as well as by the hole density. As a result, it is found that the gas response value of the film sensor is directly proportional to the apparent sensor resistance.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.816-825
• /
• 2002

During the manufacture of a ship, longitudinal deformation is produced by fillet welding on the BuiltUp beam used to improve the longitudinal strength of a ship. This deformation needs a correcting process separate from a manufacture process and decreases productivity and quality. This deformation is caused by welding moment, which is the value multiplied the shrinking force due to welding by the distance from the neutral axis on a cross section of Built-Up beam. This deformation can be offset by generating a moment which is the same magnitude with and is located in an opposite direction to the welding moment on web plate by induction heating. Accordingly, this study clarifies the creation mechanism of the longitudinal deformation on Built-Up beam with FEM analysis and presents the preventative method of this deformation by induction heating basing the mechanism and verifies its validity through analysis and experiments. The induction heating used here is performed by deciding its location and quantity with experiments and simple equations and by applying them to areal structure.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.4
• /
• pp.13-18
• /
• 2012

By the need for high-speed data transmission in PCB, the studies on the optical PCB has been conducted with optical interconnection and its packaging technology. Particularly, the polymer-based optical interconnection has been extensively studied with the advantages such as cost-effective and ease of process. For high-efficiency and passive alignment, the studies were performed using the 45 degree mirrors, MT connector, and etc. In this work, integrated PLC device and fiber alignment array block was fabricated by using imprint technology to solve the alignment and array problem of optical device and the optical fiber. The fabricated integrated block for optical interconnection of PLC device has achieved higher precision of decreasing the dimensional error of the patterns by optimization of process and its insertion loss has an average value of 4.03dB, lower than criteria specified by international standard. In addition, a optical waveguide with built-in lens has been proposed for high-efficiency and passive alignment. By simulation, it was confirmed that the proposed structure has higher coupling efficiency than conventional no-lens structure and has the broad tolerance for the spatial offset of optical waveguide.

• Journal of information and communication convergence engineering
• /
• v.16 no.1
• /
• pp.12-16
• /
• 2018

In this work, a voltage controlled oscillator (VCO) monolithic microwave integrated circuit (MMIC) was demonstrated for 10-GHz band motion detecting sensors. The VCO MMIC was fabricated using a $2-{\mu}m$ InGap/GaAs HBT process, and the tuning of the oscillation frequency is achieved by changing the internal capacitance in the HBT, instead of using extra varactor diodes. The implemented VCO MMIC has a micro size of $500{\mu}m{\times}500{\mu}m$, and demonstrates the value of inserting the VCO into a single chip transceiver. The experimental results showed that the frequency tuning characteristic was above 30 MHz, with the excellent output flatness characteristic of ${\pm}0.2dBm$ over the tuning bandwidth. And, the VCO MMIC exhibited a phase noise characteristic of -92.64 dBc/Hz and -118.28 dBc/Hz at the 100 kHz and 1 MHz offset frequencies from the carrier, respectively. The measured values were consistent with the design values, and exhibited good performance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.2
• /
• pp.207-217
• /
• 1993

In this paper, knowing a priori probability of phase offset between transmitted codes and reference codes in the receiver, we construct the state diagram of acquisition process of the direct sequence spread-spectrum communication system using the expanding window search. The scannings are performed from the cell with higher probability code epoch synchronization to that with lower one. We expand window size from initial value by r times of its previous size in each search, construct the corresponding the state diagrams, and derive average synchronization time using the Markov process and Mason's gain formula. Average synchronization times versus number of search n and detection probability $P_d$ are calculated.

• Journal of Environmental Impact Assessment
• /
• v.19 no.6
• /
• pp.625-631
• /
• 2010

The objective of this work was to investigate how carbon sink and sequestration of vegetation and soil in the development project area can impact the land use plan, in addition to carbon emission capacity of the development project when we conduct environmental impact assessment. Especially, we did this work for a development project of solar power plant which would be constructed in forest area. Through this work, we found that 1) the amount of carbon sink and sequestration largely decreased due to reduction of the green area, 2) in terms of carbon sink and sequestration, conservation of natural green area is better than construction of newly vegetated area, 3) biochar application into soil can become an alternative for increase of carbon sink, and 4) even though a solar power production does hugely reduce carbon emissions and offset the carbon sink and sequestration capacity from the forest, it is necessary to consider the public value of the forest(reduction of heat island, habitat etc.) in siting for development area.

• Phonetics and Speech Sciences
• /
• v.1 no.3
• /
• pp.65-72
• /
• 2009

Formant values are the most important acoustic correlates of English vowels. Classical studies on English vowels reported the first three formant values measured at a single timepoint on a sustained vowel segment. However, many recent studies revealed that partial onset or offset segments with information of dynamic spectral changes may contribute to the exact identification of English vowels with an accuracy almost comparable to that by the whole vowel segment or word. The purpose of this study was to examine formant trajectories of nine English vowels collected by Hillenbrand et al.(1995). Acoustic analysis was systematically made by a Praat script at six equidistant timepoints over the vowel segment. Results showed that the first formant trajectories played an important role in distinguishing each vowel within the front- or back-vowel groups. The second formant trajectories of the back vowels varied more drastically than those of the front vowels. The third formant value was similar except the high vowel /i/. From the vowel space on F1 by F2 axes, the formant trajectories of each vowel clearly showed a transition toward the locus of the following consonant /d/. Other acoustic data revealed that there were some vowel inherent duration or pitch values. From this study we can conclude that the dynamic spectral changes are very important in specifying acoustic characteristics of the English vowels. Further studies on vowels and diphthongs in different contexts are desirable.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.468-474
• /
• 2012

A low phase-noise microwave oscillator is presented by a substrate integrated waveguide(SIW) loading a complementary split ring resonator(CSRR) in this paper. The unloaded $Q$-factor of the SIW cavity is increased by loading a complementary split ring resonator(CSRR) and its value exhibits 1960. It is theoretically and experimentally demonstrated that the proposed circuit generates 11.3 dBm of output power at 9.3 GHz and a phase-noise of -127.9 dBc/Hz at 1-MHz offset.

• Composites Research
• /
• v.17 no.2
• /
• pp.28-33
• /
• 2004

Failure detection in a cross-ply laminated composite beam under tensile loading were performed using a fiber Bragg grating (FBG) sensor. A Passive Mach-Zehnder interferometric demodulator was proposed to enhance sensitivity and bandwidth. The proposed FBG sensor system without active device such as a phase modulator is very simple in configuration, easy to implement and enables the measurement of high-frequency vibration with low strain amplitude such as impact or failure signal. Failure signals detected by a FBG sensor had offset value corresponding to the strain shift with vibration at a maximum frequency of several hundreds of kilohertz. at the instant of transverse crack propagation in the 90 degree layer of composite beam.