• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.428-429
• /
• 2006

In this thesis, verifies electrical-optical characteristics of phosphorescent materials. basic structure of fabricating devices is glass/ITO/$\alpha$-NPD($300{\AA}$)/CBP:Guest($300{\AA}$)/BCP($80{\AA}$)/$Alq_3(100{\AA})$/Al($1000{\AA}$). In efficiency, fabrication of organic light emitting diodes using $Ir(btp)_2acac$ phosphorescent material is external quantum efficiency 0.268% as doping concentration 3%. At CIE coordinates, phosphorescent material $Ir(btp)_2acac$ following materials moves high purity red color(x=0.6686, y=0.3243). The brightness shows $285cd/cm^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.436-437
• /
• 2006

In this work, impedance Spectroscopic analysis was applied to study the effect of plasma treatment on the surface of indum-tin oxide (ITO) anodes using $O_2$ gas and to model the equivalent circuit for organic light emitting diodes (OLEDs) with the $O_2$ plasma treatment of ITO surface at the anodes. This device with ITO/TPD/Alq3/LiF/Al structure can be modeled as a simple combination of a resistor and a capacitor. The $O_2$ plasma treatment on the surface of ITO shifts the vacuum level of the ITO as a result of which the barrier height for hole injection at the ITO/organic interface is reduced. The impedance spectroscopy measurement of the devices with the $O_2$ plasma treatment on the surface of ITO anodes shows change of values in parallel resistance ($R_p$) and parallel capacitance ($C_p$).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.32-36
• /
• 2022

AGZO thin films were deposited on glass substrates using RF magnetron sputtering system under Ar flow rates, and their structural, electrical, and optical properties were analyzed systematically. As a result of the XRD pattern, the peak of the (002) (2θ≈33.7˚) orientation was observed, and it was found to have a hexagonal wurtzite structure. The sheet resistance of Ar 5 sccm was 3.073×10² Ω/sq and showed the best electrical properties because of the improvement of mobility due to the increase of the grain size and the variation of RMS roughness. In addition, the average transmittance was more than 90% for all samples, which demonstrated good optical properties. It is expected that the TCO characteristics can be improved by controlling Ar flow rates, and this will increase the efficiency of photoelectronic devices such as OLED and solar cells.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1029-1036
• /
• 2022

The traditional outdoor advertising market has been stagnant recently, but the digital advertising market has been steadily increasing, and the digital signage market has been expanding despite the recent corona pandemic. However, in terms of hardware, new displays are required due to excessive power consumption, lack of visibility in sunlight, and continuous operating expenses. Since the e-paper display does not require a light emitting device therein, it is advantageous to solve above problems. In addition, it has the advantage of consuming power only when converting an image due to bistability, so it is suitable as hardware that implements images rather than moving pictures. Currently, one of the most successful examples of commercializing e-paper displays is ESL devices. According to a recent market study, the market for large-sized panels larger than 10 inches has grown at an annual rate of 21.6%, and the market is expected to exceed 30% by 2026. It is judged that it will be relatively easy to apply the roll-to-roll technology, which is currently developing the technology applied to OLED, to the e-paper display. Therefore, mass production technology and market expansion for ESL panel enlargement are expected, and a new market is also expected to be formed at the same time. New markets will be traffic signs, public displays, billboards, façades, kiosks, digital signage, and so on.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.33-35
• /
• 2008

We have fabricated and evaluated new high efficiency green light emitting phosphorescent devices with an emission layer of $[TCTA_{1/3}TAZ_{2/3}/TAZ]:Ir(ppy)_3$. The whole experimental devices have the basic structure of $2-TNATA(500 {\AA})/NPB(300{\AA})/EML(300{\AA})/BCP(50{\AA})/SFC137(500{\AA})$ between anode and cathode. We have also fabricated conventional phosphorescent devices with emission layers of $(TCTA_{1/3}TAZ_{2/3}):Ir(ppy)_3$ and $(TCTA/TAZ):Ir(ppy)_3$ and compared their electroluminescence characteristics with those of the device with an emission layer of $(TCTA/TCTA_{1/3}TAZ_{2/3}/TAZ):Ir(ppy)_3$. The current density(J), luminance(L), and current efficiency($\eta$) of the device with an emission layer of $(80{\AA}-TCTA/90{\AA}-TCTA_{1/3}TAZ_{2/3}/130{\AA}-TAZ):10%-Ir(ppy)_3$ were 95 $mA/cm^2$, 25000 $cd/m^2$, and 27 cd/A at an applied voltage of 10V, respectively. The maximum current efficiency was 52 cd/A under the luminance of 400 $cd/m^2$. The peak wavelength and FWHM(full width at half maximum) in the electroluminescence spectral were 513nm and 65nm, respectively. The color coordinate was (0.30, 0.62) on the CIE (Commission Internationale de l'Eclairage) chart. Under the luminance of 15000 $cd/m^2$, the current efficiency of the device with an emission layer of $(80{\AA}-TCTA/90{\AA}-TCTA_{1/3}TAZ_{2/3}/130{\AA}-TAZ):10%-Ir(ppy)_3$ was 34 cd/A, which has been improved 1.7 times and 1.4 limes compared to those of the devices with emission layers of $(300{\AA}-TCTA_{1/3}TAZ_{2/3}): 10%-Ir(ppy)_3$ and $(100{\AA}-TCTA/200{\AA}-TAZ):10%-Ir(ppy)_3$, respectively.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.407-412
• /
• 2009

Vacuum deposited N,N-di-1-naphthyl-N,N-diphenyl-1,1'-biphenyl-4,4'-diamine (NPD) as a hole transporting (HTL) materials in OLEDs was placed on PEDOT-PSS, a hole injection layer (HIL). PEDOT-PSS was spin-coated on to the ITO glass. $C_{60}$-doped NPD-$C_{60}$(10 wt%) film was formed via co-evaporation process and the morphology of NPD-$C_{60}$ films was investigated using XRD and AFM. The J - V, L - V and current efficiency of multi -layered devices were characterized. According to XRD results, the deposited $C_{60}$ thin film was partially crystalline, but NPD-$C_{60}$ film was observed not to be crystalline, which indicates that $C_{60}$ molecules are uniformly dispersed in the NPD film. By using $C_{60}$-doped NPD-$C_{60}$ film as a HTL, the current density and luminance of multi-layered ITO/PEDOT-PSS/NPD-$C_{60}/Alq_3$/LiF/Al device were significantly increased by about 80% and its efficiency was improved by about 25% in this study.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.3
• /
• pp.77-81
• /
• 2020

Commercialization of flexible OLED displays, such as rollable and foldable displays, has attracted tremendous interest in next-generation display markets. However, during bending deformation, cracking and delamination of thin films in the flexible display panels are the critical bottleneck for the commercialization. Therefore, measuring mechanical properties of the fragile thin films in the flexible display panels is essential to prevent mechanical failures of the devices. In this study, tensile properties of the metal and ceramic nano-thin films were quantitatively measured by using a direct tensile testing method on the water surface. Elastic modulus, tensile strength, and elongation of the sputtered Mo, MoTi thin films, and PECVD deposited SiN_x thin films were successfully measured. As a result, the tensile properties were varied depending on the deposition conditions and the film thickness. The measured tensile property values can be applied to stress analysis modeling for mechanically robust flexible displays.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.251-252
• /
• 2012

Recently, the growing interest in organic microelectronic devices including OLEDs has led to an increasing amount of research into their many potential applications in the area of flexible electronic devices based on plastic substrates. However, these organic devices require a gas barrier coating to prevent the permeation of water and oxygen because organic materials are highly susceptible to water and oxygen. In particular, high efficiency OLEDs require an extremely low Water Vapor Transition Rate (WVTR) of $1{\times}10^{-6}g/m^2$/day. The Key factor in high quality inorganic gas barrier formation for achieving the very low WVTR required ($1{\times}10^{-6}g/m^2$/day) is the suppression of defect sites and gas diffusion pathways between grain boundaries. In this study, we developed an $Al_2O_3$ nano-crystal structure single gas barrier layer using a Neutral Beam Assisted Sputtering (NBAS) process. The NBAS system is based on the conventional RF magnetron sputtering and neutral beam source. The neutral beam source consists of an electron cyclotron Resonance (ECR) plasma source and metal reflector. The Ar+ ions in the ECR plasma are accelerated in the plasma sheath between the plasma and reflector, which are then neutralized by Auger neutralization. The neutral beam energies were possible to estimate indirectly through previous experiments and binary collision model. The accelerating potential is the sum of the plasma potential and reflector bias. In previous experiments, while adjusting the reflector bias, changes in the plasma density and the plasma potential were not observed. The neutral beam energy is controlled by the metal reflector bias. The NBAS process can continuously change crystalline structures from an amorphous phase to nano-crystal phase of various grain sizes within a single inorganic thin film. These NBAS process effects can lead to the formation of a nano-crystal structure barrier layer which effectively limits gas diffusion through the pathways between grain boundaries. Our results verify the nano-crystal structure of the NBAS processed $Al_2O_3$ single gas barrier layer through dielectric constant measurement, break down field measurement, and TEM analysis. Finally, the WVTR of $Al_2O_3$ nano-crystal structure single gas barrier layer was measured to be under $5{\times}10^{-6}g/m^2$/day therefore we can confirm that NBAS processed $Al_2O_3$ nano-crystal structure single gas barrier layer is suitable for OLED application.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.115-116
• /
• 2012

The demand for flexible electronic systems such as wearable computers, E-paper, and flexible displays has increased due to their advantages of excellent portability, conformal contact with curved surfaces, light weight, and human friendly interfaces over present rigid electronic systems. This seminar introduces three recent progresses that can extend the application of high performance flexible inorganic electronics. The first part of this seminar will introduce a RRAM with a one transistor-one memristor (1T-1M) arrays on flexible substrates. Flexible memory is an essential part of electronics for data processing, storage, and radio frequency (RF) communication and thus a key element to realize such flexible electronic systems. Although several emerging memory technologies, including resistive switching memory, have been proposed, the cell-to-cell interference issue has to be overcome for flexible and high performance nonvolatile memory applications. The cell-to-cell interference between neighbouring memory cells occurs due to leakage current paths through adjacent low resistance state cells and induces not only unnecessary power consumption but also a misreading problem, a fatal obstacle in memory operation. To fabricate a fully functional flexible memory and prevent these unwanted effects, we integrated high performance flexible single crystal silicon transistors with an amorphous titanium oxide (a-TiO2) based memristor to control the logic state of memory. The $8{\times}8$ NOR type 1T-1M RRAM demonstrated the first random access memory operation on flexible substrates by controlling each memory unit cell independently. The second part of the seminar will discuss the flexible GaN LED on LCP substrates for implantable biosensor. Inorganic III-V light emitting diodes (LEDs) have superior characteristics, such as long-term stability, high efficiency, and strong brightness compared to conventional incandescent lamps and OLED. However, due to the brittle property of bulk inorganic semiconductor materials, III-V LED limits its applications in the field of high performance flexible electronics. This seminar introduces the first flexible and implantable GaN LED on plastic substrates that is transferred from bulk GaN on Si substrates. The superb properties of the flexible GaN thin film in terms of its wide band gap and high efficiency enable the dramatic extension of not only consumer electronic applications but also the biosensing scale. The flexible white LEDs are demonstrated for the feasibility of using a white light source for future flexible BLU devices. Finally a water-resist and a biocompatible PTFE-coated flexible LED biosensor can detect PSA at a detection limit of 1 ng/mL. These results show that the nitride-based flexible LED can be used as the future flexible display technology and a type of implantable LED biosensor for a therapy tool. The final part of this seminar will introduce a highly efficient and printable BaTiO3 thin film nanogenerator on plastic substrates. Energy harvesting technologies converting external biomechanical energy sources (such as heart beat, blood flow, muscle stretching and animal movements) into electrical energy is recently a highly demanding issue in the materials science community. Herein, we describe procedure suitable for generating and printing a lead-free microstructured BaTiO3 thin film nanogenerator on plastic substrates to overcome limitations appeared in conventional flexible ferroelectric devices. Flexible BaTiO3 thin film nanogenerator was fabricated and the piezoelectric properties and mechanically stability of ferroelectric devices were characterized. From the results, we demonstrate the highly efficient and stable performance of BaTiO3 thin film nanogenerator.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.157-157
• /
• 2015

Recently, the growing interest in organic microelectronic devices including OLEDs has led to an increasing amount of research into their many potential applications in the area of flexible electronic devices based on plastic substrates. However, these organic devices require a gas barrier coating to prevent the permeation of water and oxygen because organic materials are highly susceptible to water and oxygen. In particular, high efficiency OLEDs require an extremely low water vapor transition rate (WVTR) of $1{\times}10^{-6}g/m^2day$. The Key factor in high quality inorganic gas barrier formation for achieving the very low WVTR required ($1{\times}10^{-6}g/m^2day$) is the suppression of defect sites and gas diffusion pathways between grain boundaries. In this study NBAS process was introduced to deposit enhanced film density single gas barrier layer with a low WVTR. Fig. 1. shows a schematic illustration of the NBAS apparatus. The NBAS process was used for the $Al_2O_3$ nano-crystal structure films deposition, as shown in Fig. 1. The NBAS system is based on the conventional RF magnetron sputtering and it has the electron cyclotron resonance (ECR) plasma source and metal reflector. $Ar^+$ ion in the ECR plasma can be accelerated into the plasma sheath between the plasma and metal reflector, which are then neutralized mainly by Auger neutralization. The neutral beam energy is controlled by the metal reflector bias. The controllable neutral beam energy can continuously change crystalline structures from an amorphous phase to nanocrystal phase of various grain sizes. The $Al_2O_3$ films can be high film density by controllable Auger neutral beam energy. we developed $Al_2O_3$ high dense barrier layer using NBAS process. We can verified that NBAS process effect can lead to formation of high density nano-crystal structure barrier layer. As a result, Fig. 2. shows that the NBAS processed $Al_2O_3$ high dense barrier layer shows excellent WVTR property as a under $2{\times}10^{-5}g/m^2day$ in the single barrier layer of 100nm thickness. Therefore, the NBAS processed $Al_2O_3$ high dense barrier layer is very suitable in the high efficiency OLED application.