• 한국유체기계학회 논문집
• /
• 제14권5호
• /
• pp.48-54
• /
• 2011

Structural modifications of a ship may cause a fatal accident such as sinking and wrecking of ship. Especially, barge ship can be easily reconstructed to load more bulk cargo. In this study, for a real accident case, change of mooring force due to structural modification was analyzed to evaluate accident risk. A two dimensional dynamic model for the barge ship was constructed to compute mooring forces with related to floating motion. The equation of motion was established in Matlab code and buoyancy was calculated by using direct integration of submerged volume. The results showed that wind force, current force, and mooring force after rebuilding was approximately 4.3 kN, 14 kN, 1,561 kN respectively. The maximum force of mooring force according to the length of mooring cable were 1,614 kN at 30 m of mooring cable. Thus, an arbitrary modification of ship lead instability and unreliable result so that illegal rebuilding of ship should be avoided.

• 한국공간구조학회논문집
• /
• 제14권3호
• /
• pp.47-56
• /
• 2014

This paper investigates the characteristics of unstable behaviour and critical buckling load by joint rigidity of framed large spatial structures which are sensitive to initial conditions. To distinguish the stable from the unstable, a singular point on equilibrium path and a critical buckling level are computed by the eigenvalues and determinants of the tangential stiffness matrix. For the case study, a two-free node example and a folded plate typed long span example with 325 nodes are adopted, and these adopted examples' nonlinear analysis and unstable characteristics are analyzed. The numerical results in the case of the two-free node example indicate that as the influence of snap-through is bigger; that of bifurcation buckling is lower than that of the joint rigidity as the influence of snap-through is lower. Besides, when the rigidity decreases, the critical buckling load ratio increases. These results are similar to those of the folded-typed long span example. When the buckling load ratio is 0.6 or less, the rigidity greatly increases.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.83-86
• /
• 2002

Numerical simulations are conducted for laminar flow past a sphere rotating In the transverse direction, in order to investigate the effect of the rotation on the characteristics of flow over a sphere. The Reynolds numbers considered are Re=100, 250 and 300 based on the free-stream velocity and the sphere diameter, and the rotational speeds are in the range of $0{\leq}{\omega}{\leq}1$, where ${\omega}^{\ast}$ is the maximum velocity on the sphere surface normalized by the free-stream velocity. At ${\omega}^{\ast}=0$ (without rotation), the flow past the sphere experiences steady axisymmeoy, steady planar-symmetry and unsteady planar-symmetry, respectively, at Re=100, 250 and 300. However, with rotation, the flow becomes planar-symmetric for all the cases investigated and the symmetry plane is orthogonal to the axis of the rotation. The flow is also steady or unsteady depending on both the Reynolds number and the rotational speed, and the vortical structures behind the sphere are significantly modified by the rotation. For example, at Re=300, hairpin vortices completely disappear in the wake at ${\omega}^{\ast}=0.4\;and\;0.6$, and at ${\omega}^{\ast}=1$ vortical structures of a high frequency are newly generated due to the shear layer instability. It is also shown that with increasing rotational speed, the time-averaged drag and lift coefficients increase monotonically.

• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.2010-2018
• /
• 2003

Although continuous casting process has highly developed, there still remain many problems to be considered. Specifically, two vortex flows resulting from impingement against narrow walls make a flow field unstable in a mold, and it is directly related to internal and external defects of steel products. To cope with this instability, EMBR (Electromagnetic Brake Ruler) technique has been lately studied for the stability of molten steel flow, and it is revealed that molten steel flow in a mold can be controlled with applied magnetic field. However, it is still difficult to clarify flow pattern in an EMBR caster due to complex correlations among variables such as geometric factors, casting conditions, and the place and the intensity of charged magnetic field. In the present study, flow field in a mold is focused with different conditions of electromagnetic effect. To accurately analyze the case, three dimensional low Reynolds turbulent model and appropriate boundary conditions are chosen. To evaluate the electromagnetic effect in molten steel flow, dimensionless numbers are employed. The results show that the location and the intensity of the applied magnetic field significantly influence the flow pattern. Both impingement and internal flow pattern are changed remarkably with the change of the location of applied magnetic field. It turns out that an insufficient magnetic force yields adverse effect like channeling, and rather lowers the quality of steel product.

• 한국추진공학회지
• /
• 제7권4호
• /
• pp.63-72
• /
• 2003

배플이 장착된 KSR-III 엔진의 연소장 및 성능을 예측하기 위하여 수치해석을 수행하였다. 수치해석의 검증을 위해 3차원 계산을 수행하여 연소시험과 비교하였으며, 정성적으로 잘 일치하는 것을 볼 수 있었다. 배플이 장착됨에 따라 연소실 전압이 감소하여 특성속도가 감소하는 것을 볼 수 있었고, 이것은 엔진의 성능 감소로 이어지는 것을 알 수 있었다. 또한 분사기 면과 연소실 벽면 및 배플 벽면에 국부적인 고온 영역이 발생하는 것을 볼 수 있었으며, 이것은 분사기 면에 막냉각을 설계하여 장착할 수 있는 기본 자료로 활용되었고 실제 엔진에 적용되었다.

• Structural Engineering and Mechanics
• /
• 제31권1호
• /
• pp.39-56
• /
• 2009

Vibration is an undesirable phenomenon in a dynamic system like lightly damped aerospace structures and active vibration control has gradually been employed to suppress vibration. The objective of the current investigation is to introduce an active torsional magneto-rheological (MR) fluid based damper for vibration control of a typical nose landing gear. They offer the adaptability of active control devices without requiring the associated large power sources. A torsional damper is designed and developed based on Bingham plastic shear flow model. The numerical analysis is carried out to estimate the damping coefficient and damping force. The designed damper is fabricated and an experimental setup is also established to characterize the damper and these results are compared with the analytical results. A typical FE model of Nose landing gear is developed to study the effectiveness of the damper. Open loop response analysis has been carried out and response levels are monitored at the piston tip of a nose landing gear for various loading conditions without damper and with MR-damper as semi-active device. The closed-loop full state feedback control scheme by the pole-placement technique is also applied to control the landing gear instability of an aircraft.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 봄 학술발표회 논문집
• /
• pp.193-200
• /
• 2003

This paper presents a hybrid (i.e., integrated passive-active) system for seismic response control of a cable-stayed bridge. Because multiple control devices are operating, a hybrid control system could alleviate some of the restrictions and limitations that exist when each system is acting alone. Lead rubber bearings are used as passive control devices to reduce the earthquake-induced forces in the bridge and hydraulic actuators are used as active control devices to further reduce the bridge responses, especially deck displacements. In the proposed hybrid control system, a linear quadratic Gaussian control algorithm is adopted as a primary controller. In addition, a secondary bang-bang type (i.e., on-off type) controller according to the responses of lead rubber bearings is considered to increase the controller robustness. Numerical simulation results show that control performances of the hybrid control system are superior to those of the passive control system and slightly better than those of the fully active control system. Furthermore, it is verified that the hybrid control system with a bang-bang type controller is more robust for stiffness perturbation than the active controller with μ-synthesis method and there are no signs of instability in the overall system whereas the active control system with linear quadratic Gaussian algorithm shows instabilities in the perturbed system. Therefore, the proposed hybrid protective system could effectively be used to seismically excited cable-stayed bridges.

• 한국전산구조공학회논문집
• /
• 제17권3호
• /
• pp.225-239
• /
• 2004

이 논문에서는 철근콘크리트 골조 구조물의 시공 시 작용하는 사하중, 활하중, 시공하중 등의 하중에 대한 지지 및 안전한 시공을 위해 설치되는 지지시스템에 대하여 보다 체계적인 분석이 이루어졌다. 지지시스템의 종류, 비계의 강성과 간격 등의 변화에 따른 구조물의 거동특성을 비교, 분석하였고, 기존의 설계규준 및 해석방법과의 비교를 위해 크리프 등의 시간의존적 거동을 고려한 경우와 괴려하지 않은 경우에 대하여 해석이 수행되었으며, 나무 비계를 사용한 경우와 강재 비계를 사용한 경우에 대한 비교 검토가 이루어졌다. 또한, 대표적인 3-경간 구조물에 대한 해석을 수행하여 내측 기둥과 외측 기둥의 부등축소에 따른 영향을 반영한 검토가 이루어졌다. 나아가 다양한 설계인자의 변화에 따른 거동분석을 통해 2SlR 지지시스템이 가장 효율적임을 제시하였다.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제10권1호
• /
• pp.50-63
• /
• 2002

The Karman boundary-layer has been numerically investigated for the disturbance wave number, wave velocity, azimuth angle and radius (Reynolds number, Re). The disturbed flow over rotating disk can lead to transition at a much lower Re than that of the well-known Type I instability. This early transition is due to the excitation of the Type II. Presented are the neutral stability results concerning these instabilities by solving newly formulated stability equations with consideration of whole convective terms. When the present numerical results are compared with the previously known results, the value of critical Re corresponding to Type I is moved from ${Re}_{c.1}$=285.3 to 270.2 and the value corresponding to Type II from ${Re}_{c.2}$=69.4 to 36.9, respectively. Also, the corresponding wave number is moved fro)m $k_1$=0.378 to 0.386 for Type I; from $k_2$=0.279 to 0.385 for Type II. For Type II, the upped limit of wave number and azimuth angle is $k_u$=0.5872, $\varepsilon_u$=$-17.5^{\circ}$, while its lower limit is near $k_u$=0, $\varepsilon_u$=$-28.4^{\circ}$. This implies that the disturbances will be relatively fast amplified at small Re and within narrow bands of wave number compared with the previous results.

• 한국해양공학회지
• /
• 제18권5호
• /
• pp.15-21
• /
• 2004

An edge tone is the discrete tone or narrow-band sound produced by an oscillating free shear layer, impinging on a rigid surface. In this paper, we present a 2-D edge tone to predict the frequency characteristics of the discrete oscillations of a jet-edge feedback cycle, using the finite difference lattice Boltzmann method (FDLBM). We use a modified version of the lattice BGK compressible fluid model, adding an additional term and allowing for longer time increments, compared to a conventional FDLBM, and also use a boundary fitted coordinates system. The jet is chosen long enough in order to guarantee the parabolic velocity profile of the jet at the outlet, and the edge consists of a wedge with an angle of ${\alpha}$ = 23. At a stand-off distance, the edge is inserted along the centerline of the jet, and a sinuous instability wave, with real frequency, is assumed to be created in the vicinity of the nozzle and propagates towards the downstream. We have succeeded in capturing very small pressure fluctuations, resulting from periodical oscillations of a jet around the edge. The pressure fluctuations propagate with the speed of sound. Its interaction with the wedge produces an non-rotational feedback field, which, near the nozzle exit, is a periodic transverse flow, producing the singularities at the nozzle lips.